B41042

Aluminum electrolytic capacitors Alu-X product lines Single-ended capacitors Series/Type: Data Sheet Date: B41042 August 2008 © EPCOS AG 2008. Reproduction, publication and dissemination of this publication and the information contained therein without EPCOS’ prior express consent is prohibited. Long-life grade capacitors Applications Single-ended capacitors Low impedance – 105 °C Single-ended capacitors Low impedance – 105 °C B41042 B41042 ■ Professional switch mode power supplies Features ■ ■ ■ ■ RoHS-compatible High C/V value Low impedance at high frequencies Load life of 5000 h at 105 °C Construction ■ ■ ■ ■ ■ Radial leads Aluminum case, fully insulated Charge-discharge proof Minus pole marking on the insulating sleeve Case with safety vent from diameter 8 mm Delivery mode ■ ■ ■ ■ Bulk Taped, Ammo pack Cut Kinked Please read Cautions and warnings and Important notes at the end of this document. 2 08/08 Single-ended capacitors Low impedance – 105 °C Specifications and characteristics in brief Rated voltage VR Operating temp. range Rated capacitance CR (20 °C, 120 Hz) Capacitance tolerance Load life (105 °C, VR, IAC,R) 6.3 ... 80 V DC –55 °C … +105 °C 0.47 … 15000 µF ± 20% M B41042 2000 h for d = 5 ... 6.3 mm 3000 h for d = 8 mm 5000 h for d ≥ 10 mm CR VR I leak ≤ 0.03 µA ⋅ ⎛ ------- ⋅ ------ ⎞ or 4 µA ⎝ µF V ⎠ Requirements: ∆C/C ≤ ± 25% of initial value tan δ ≤ 2 times initial specified limit Ileak ≤ initial specified limit Leakage current Ileak (20 °C, after 1 minute) Dissipation factor (max.) For capacitance higher than 1000 µF add 0.02 for every increase of (20 °C, 120 Hz) 1000 µF. VR (V DC) tan δ Low temperature stability (impedance ratio) (120 Hz) Shelf life VR (V DC) Z ( – 55 °C ) -------------------------Z ( +20 °C ) 6.3 0.22 4 10 0.19 16 0.16 3 25 0.14 35 0.12 50 63 80 0.10 0.09 0.08 50 … 80 2 6.3 … 10 16 … 35 After storage for 1000 h at 105 °C, the capacitors shall meet the requirement of load life test after reforming process. After test: VR to be applied for 30 minutes, 24 to 48 hours before measurement. 50 Hz 120 Hz 500 Hz 1 kHz 10 kHz 100 kHz 0.40 0.60 0.80 0.55 0.70 0.80 0.90 +85 °C 1.68 0.65 0.80 0.85 0.95 0.80 0.90 0.98 0.98 0.90 0.95 1.00 1.00 1.00 1.00 1.00 1.00 Frequency multiplier for rated ripple current 0.47 … 27 µF 33 … 330 µF 1200 µF Temperature multiplier for rated ripple current +70 °C 1.96 390 … 1000 µF 0.65 +105 °C 1.00 Please read Cautions and warnings and Important notes at the end of this document. 3 08/08 Single-ended capacitors Low impedance – 105 °C Dimensional drawing B41042 d l + 15 min. 5 min. KAL1080-C-E Minus pole marking a Safety vent Safety vent for diameter ≥ 8 mm. Case dimensions d×l mm 5 8 10 10 10 × 11 × 11.5 × 12.5 × 16 × 20 6.3 × 11 dmax × Imax mm 5.5 × 12.5 6.8 × 12.5 8.5 × 13.0 11.0 × 14.0 11.0 × 17.5 11.0 × 21.5 13.5 × 22.0 13.5 × 27.0 13.5 × 33.5 13.5 × 37.5 13.5 × 42.0 17.0 × 27.0 17.0 × 33.5 17.0 × 37.5 17.0 × 42.0 19.0 × 37.5 19.0 × 42.0 a mm 2.0 ± 0.5 2.5 ± 0.5 3.5 ± 0.5 5.0 ± 0.5 5.0 ± 0.5 5.0 ± 0.5 5.0 ± 0.5 5.0 ± 0.5 5.0 ± 0.5 5.0 ± 0.5 5.0 ± 0.5 7.5 ± 0.5 7.5 ± 0.5 7.5 ± 0.5 7.5 ± 0.5 7.5 ± 0.5 7.5 ± 0.5 b mm 0.5 ± 0.1 0.5 ± 0.1 0.6 ± 0.1 0.6 ± 0.1 0.6 ± 0.1 0.6 ± 0.1 0.6 ± 0.1 0.6 ± 0.1 0.6 ± 0.1 0.6 ± 0.1 0.6 ± 0.1 0.8 ± 0.1 0.8 ± 0.1 0.8 ± 0.1 0.8 ± 0.1 0.8 ± 0.1 0.8 ± 0.1 12.5 × 20 12.5 × 25 12.5 × 31.5 12.5 × 35.5 12.5 × 40 16 16 16 16 18 18 × 25 × 31.5 × 35.5 × 40 × 35.5 × 40 Please read Cautions and warnings and Important notes at the end of this document. 4 øb 08/08 Single-ended capacitors Low impedance – 105 °C Overview of available types VR (V DC) CR (µF) 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 10000 12000 15000 5 5 × 11 × 11 5 5 × 11 × 11 5 5 × 11 × 11 5 5 6.3 10 16 B41042 25 Case dimensions d × l (mm) × 11 × 11 6.3 × 11 6.3 × 11 6.3 × 11 6.3 × 11 6.3 × 15 6.3 × 15 8 10 10 10 10 10 10 10 10 × 11.5 × 12.5 × 12.5 × 16 × 16 × 20 × 20 × 25 × 31.5 6.3 × 11 6.3 × 11 6.3 × 11 6.3 × 11 6.3 × 15 6.3 × 15 8 10 10 10 10 10 10 10 10 × 11.5 × 12.5 × 12.5 × 16 × 16 × 20 × 20 × 25 × 31.5 6.3 × 11 6.3 × 11 6.3 × 11 6.3 × 11 6.3 × 15 6.3 × 15 8 10 10 10 10 10 10 10 10 × 11.5 × 12.5 × 12.5 × 16 × 16 × 20 × 20 × 25 × 31.5 6.3 × 11 6.3 × 11 6.3 × 11 6.3 × 15 6.3 × 15 8 10 10 10 10 10 10 10 10 10 × 11.5 × 12.5 × 12.5 × 16 × 16 × 20 × 20 × 25 × 31.5 × 31.5 12.5 × 20 12.5 × 25 12.5 × 25 12.5 × 31.5 12.5 × 35.5 12.5 × 40 16 16 16 18 × 31.5 × 35.5 × 40 × 40 12.5 × 20 12.5 × 25 12.5 × 31.5 12.5 × 31.5 12.5 × 35.5 12.5 × 40 16 16 16 18 18 × 31.5 × 35.5 × 40 × 35.5 × 40 12.5 × 20 12.5 × 25 12.5 × 31.5 12.5 × 35.5 12.5 × 40 16 16 16 16 18 × 31.5 × 35.5 × 35.5 × 40 × 40 12.5 × 25 12.5 × 25 12.5 × 31.5 12.5 × 35.5 12.5 × 40 16 16 16 18 18 × 31.5 × 35.5 × 40 × 35.5 × 40 Please read Cautions and warnings and Important notes at the end of this document. 5 08/08 Single-ended capacitors Low impedance – 105 °C Overview of available types VR (V DC) CR (µF) 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 5 5 × 11 × 11 5 5 5 5 5 5 5 5 5 5 5 5 × 11 × 11 × 11 × 11 × 11 × 11 × 11 × 11 × 11 × 11 × 11 × 11 5 5 × 11 × 11 5 5 35 50 63 B41042 80 Case dimensions d × l (mm) × 11 × 11 6.3 × 11 6.3 × 11 6.3 × 11 6.3 × 11 6.3 × 15 6.3 × 15 8 10 10 10 10 10 10 10 10 × 11.5 × 12.5 × 12.5 × 16 × 20 × 20 × 25 × 31.5 × 31.5 6.3 × 11 6.3 × 11 6.3 × 11 6.3 × 11 6.3 × 15 6.3 × 15 8 10 10 10 10 10 10 10 × 11.5 × 12.5 × 12.5 × 16 × 20 × 20 × 25 × 31.5 6.3 × 11 6.3 × 11 6.3 × 11 6.3 × 11 6.3 × 15 6.3 × 15 8 10 10 10 10 10 10 10 10 × 11.5 × 12.5 × 16 × 16 × 20 × 20 × 25 × 31.5 × 31.5 6.3 × 11 6.3 × 11 6.3 × 11 6.3 × 11 6.3 × 15 6.3 × 15 8 10 10 10 10 10 10 10 10 × 11.5 × 12.5 × 12.5 × 16 × 16 × 20 × 20 × 25 × 31.5 12.5 × 25 12.5 × 31.5 12.5 × 31.5 12.5 × 35.5 12.5 × 40 16 16 16 18 18 × 31.5 × 35.5 × 40 × 35.5 × 40 12.5 × 20 12.5 × 25 12.5 × 25 12.5 × 31.5 12.5 × 35.5 12.5 × 40 16 16 16 18 × 31.5 × 35.5 × 40 × 40 12.5 × 25 12.5 × 25 12.5 × 31.5 12.5 × 35.5 12.5 × 40 16 16 × 31.5 × 35.5 12.5 × 20 12.5 × 25 12.5 × 25 12.5 × 31.5 12.5 × 35.5 Please read Cautions and warnings and Important notes at the end of this document. 6 08/08 Single-ended capacitors Low impedance – 105 °C Overview of available types VR (V DC) CR (µF) 1500 1800 2200 2700 3300 12.5 × 40 16 16 16 18 × 31.5 × 35.5 × 40 × 40 16 18 18 × 40 × 35.5 × 40 35 50 63 B41042 80 Case dimensions d × l (mm) Please read Cautions and warnings and Important notes at the end of this document. 7 08/08 Single-ended capacitors Low impedance – 105 °C Technical data and ordering codes VR V DC 6.3 CR 120 Hz 20 °C µF 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 10000 12000 15000 Case dimensions d×l mm 5 5 6.3 6.3 6.3 6.3 6.3 8 10 10 10 10 10 10 10 10 10 12.5 12.5 12.5 12.5 12.5 16 16 16 18 18 × 11 × 11 × 11 × 11 × 11 × 15 × 15 × 11.5 × 12.5 × 12.5 × 16 × 16 × 20 × 20 × 25 × 31.5 × 31.5 × 25 × 25 × 31.5 × 35.5 × 40 × 31.5 × 35.5 × 40 × 35.5 × 40 Zmax 100 kHz 20 °C Ω 1.200 1.100 1.000 0.900 0.870 0.700 0.580 0.480 0.390 0.350 0.300 0.270 0.230 0.200 0.160 0.120 0.095 0.092 0.090 0.080 0.061 0.059 0.056 0.050 0.045 0.040 0.036 IAC,R 100 kHz 105 °C mA 152 176 227 253 287 374 400 448 551 597 731 796 953 1022 1221 1375 1472 1592 1711 1914 2102 2373 2376 2551 2753 2825 2963 B41042 Ordering codes (composition see below) B41042A2107M*** B41042A2127M*** B41042A2157M*** B41042A2187M*** B41042A2227M*** B41042A2277M*** B41042A2337M*** B41042A2397M*** B41042A2477M*** B41042A2567M*** B41042A2687M*** B41042A2827M*** B41042A2108M*** B41042A2128M*** B41042A2158M*** B41042A2188M*** B41042A2228M*** B41042A2278M*** B41042A2338M*** B41042A2398M*** B41042A2478M*** B41042A2568M*** B41042A2688M*** B41042A2828M*** B41042A2109M*** B41042A2129M*** B41042A2159M*** *** = Version 000 = for 001 = for 002 = for 016 = for 007 = for 006 = for 008 = for standard leads, bulk kinked leads, bulk cut leads, bulk taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, lead lead lead lead spacing spacing spacing spacing a a a a = = = = 2.0 2.5 3.5 5.0 mm mm mm mm Please read Cautions and warnings and Important notes at the end of this document. 8 08/08 Single-ended capacitors Low impedance – 105 °C Technical data and ordering codes VR V DC 10 CR 120 Hz 20 °C µF 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 10000 Case dimensions d×l mm 5 5 6.3 6.3 6.3 6.3 6.3 6.3 8 10 10 10 10 10 10 10 10 12.5 12.5 12.5 12.5 12.5 16 16 16 16 18 × 11 × 11 × 11 × 11 × 11 × 11 × 15 × 15 × 11.5 × 12.5 × 12.5 × 16 × 16 × 20 × 20 × 25 × 31.5 × 20 × 25 × 31.5 × 35.5 × 40 × 31.5 × 35.5 × 35.5 × 40 × 40 Zmax 100 kHz 20 °C Ω 1.600 1.400 1.200 1.000 0.820 0.680 0.580 0.520 0.470 0.430 0.390 0.330 0.280 0.230 0.180 0.160 0.120 0.100 0.090 0.080 0.068 0.063 0.056 0.050 0.045 0.041 0.360 IAC,R 100 kHz 105 °C mA 152 176 211 236 268 291 372 405 463 552 596 733 798 987 1061 1282 1443 1472 1715 1941 2184 2362 2422 2613 2682 2812 3045 B41042 Ordering code (composition see below) B41042A3686M*** B41042A3826M*** B41042A3107M*** B41042A3127M*** B41042A3157M*** B41042A3187M*** B41042A3227M*** B41042A3277M*** B41042A3337M*** B41042A3397M*** B41042A3477M*** B41042A3567M*** B41042A3687M*** B41042A3827M*** B41042A3108M*** B41042A3128M*** B41042A3158M*** B41042A3188M*** B41042A3228M*** B41042A3278M*** B41042A3338M*** B41042A3398M*** B41042A3478M*** B41042A3568M*** B41042A3688M*** B41042A3828M*** B41042A3109M*** *** = Version 000 = for 001 = for 002 = for 016 = for 007 = for 006 = for 008 = for standard leads, bulk kinked leads, bulk cut leads, bulk taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, lead lead lead lead spacing spacing spacing spacing a a a a = = = = 2.0 2.5 3.5 5.0 mm mm mm mm Please read Cautions and warnings and Important notes at the end of this document. 9 08/08 Single-ended capacitors Low impedance – 105 °C Technical data and ordering codes VR V DC 16 CR 120 Hz 20 °C µF 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 Case dimensions d×l mm 5 5 6.3 6.3 6.3 6.3 6.3 6.3 8 10 10 10 10 10 10 10 10 12.5 12.5 12.5 12.5 12.5 12.5 16 16 16 18 18 × 11 × 11 × 11 × 11 × 11 × 11 × 15 × 15 × 11.5 × 12.5 × 12.5 × 16 × 16 × 20 × 20 × 25 × 31.5 × 20 × 25 × 31.5 × 31.5 × 35.5 × 40 × 31.5 × 35.5 × 40 × 35.5 × 40 Zmax 100 kHz 20 °C Ω 1.200 1.000 0.900 0.780 0.580 0.550 0.520 0.500 0.470 0.420 0.390 0.310 0.230 0.210 0.180 0.150 0.120 0.100 0.082 0.075 0.068 0.062 0.056 0.050 0.045 0.041 0.036 0.035 IAC,R 100 kHz 105 °C mA 155 176 221 243 267 292 376 408 462 553 597 731 772 954 1021 1225 1411 1432 1665 1881 2015 2223 1412 2471 2585 2822 2903 3041 B41042 Ordering code (composition see below) B41042A4476M*** B41042A4566M*** B41042A4686M*** B41042A4826M*** B41042A4107M*** B41042A4127M*** B41042A4157M*** B41042A4187M*** B41042A4227M*** B41042A4277M*** B41042A4337M*** B41042A4397M*** B41042A4477M*** B41042A4567M*** B41042A4687M*** B41042A4827M*** B41042A4108M*** B41042A4128M*** B41042A4158M*** B41042A4188M*** B41042A4228M*** B41042A4278M*** B41042A4338M*** B41042A4398M*** B41042A4478M*** B41042A4568M*** B41042A4688M*** B41042A4828M*** *** = Version 000 = for 001 = for 002 = for 016 = for 007 = for 006 = for 008 = for standard leads, bulk kinked leads, bulk cut leads, bulk taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, lead lead lead lead spacing spacing spacing spacing a a a a = = = = 2.0 2.5 3.5 5.0 mm mm mm mm Please read Cautions and warnings and Important notes at the end of this document. 10 08/08 Single-ended capacitors Low impedance – 105 °C Technical data and ordering codes VR V DC 25 CR 120 Hz 20 °C µF 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 Case dimensions d×l mm 5 5 6.3 6.3 6.3 6.3 6.3 6.3 8 10 10 10 10 10 10 10 10 12.5 12.5 12.5 12.5 12.5 12.5 16 16 16 18 × 11 × 11 × 11 × 11 × 11 × 11 × 15 × 15 × 11.5 × 12.5 × 12.5 × 16 × 16 × 20 × 20 × 25 × 31.5 × 20 × 25 × 25 × 31.5 × 35.5 × 40 × 31.5 × 35.5 × 40 × 40 Zmax 100 kHz 20 °C Ω 1.500 1.300 1.200 1.000 0.830 0.750 0.580 0.500 0.430 0.400 0.390 0.300 0.230 0.200 0.180 0.160 0.130 0.110 0.090 0.080 0.072 0.062 0.056 0.050 0.045 0.040 0.036 IAC,R 100 kHz 105 °C mA 156 173 212 237 261 228 372 409 461 553 628 753 798 986 1021 1223 1424 1433 1661 1765 1982 2080 2361 2471 2662 2821 2965 B41042 Ordering code (composition see below) B41042A5336M*** B41042A5396M*** B41042A5476M*** B41042A5566M*** B41042A5686M*** B41042A5826M*** B41042A5107M*** B41042A5127M*** B41042A5157M*** B41042A5187M*** B41042A5227M*** B41042A5277M*** B41042A5337M*** B41042A5397M*** B41042A5477M*** B41042A5567M*** B41042A5687M*** B41042A5827M*** B41042A5108M*** B41042A5128M*** B41042A5158M*** B41042A5188M*** B41042A5228M*** B41042A5278M*** B41042A5338M*** B41042A5398M*** B41042A5478M*** *** = Version 000 = for 001 = for 002 = for 016 = for 007 = for 006 = for 008 = for standard leads, bulk kinked leads, bulk cut leads, bulk taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, lead lead lead lead spacing spacing spacing spacing a a a a = = = = 2.0 2.5 3.5 5.0 mm mm mm mm Please read Cautions and warnings and Important notes at the end of this document. 11 08/08 Single-ended capacitors Low impedance – 105 °C Technical data and ordering codes VR V DC 35 CR 120 Hz 20 °C µF 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 Case dimensions d×l mm 5 5 6.3 6.3 6.3 6.3 6.3 6.3 8 10 10 10 10 10 10 10 10 12.5 12.5 12.5 12.5 12.5 12.5 16 16 16 18 × 11 × 11 × 11 × 11 × 11 × 11 × 15 × 15 × 11.5 × 12.5 × 12.5 × 16 × 16 × 20 × 20 × 25 × 31.5 × 20 × 25 × 25 × 31.5 × 35.5 × 40 × 31.5 × 35.5 × 40 × 40 Zmax 100 kHz 20 °C Ω 1.500 1.300 1.200 0.830 0.720 0.520 0.470 0.420 0.390 0.340 0.300 0.260 0.230 0.210 0.180 0.150 0.120 0.100 0.085 0.075 0.068 0.062 0.056 0.050 0.045 0.040 0.036 IAC,R 100 kHz 105 °C mA 161 182 227 246 271 298 372 418 463 551 599 731 796 986 1061 1222 1423 1431 1663 1765 1982 2184 2362 2475 2684 2903 3041 B41042 Ordering code (composition see below) B41042A7226M*** B41042A7276M*** B41042A7336M*** B41042A7396M*** B41042A7476M*** B41042A7566M*** B41042A7686M*** B41042A7826M*** B41042A7107M*** B41042A7127M*** B41042A7157M*** B41042A7187M*** B41042A7227M*** B41042A7277M*** B41042A7337M*** B41042A7397M*** B41042A7477M*** B41042A7567M*** B41042A7687M*** B41042A7827M*** B41042A7108M*** B41042A7128M*** B41042A7158M*** B41042A7188M*** B41042A7228M*** B41042A7278M*** B41042A7338M*** *** = Version 000 = for 001 = for 002 = for 016 = for 007 = for 006 = for 008 = for standard leads, bulk kinked leads, bulk cut leads, bulk taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, lead lead lead lead spacing spacing spacing spacing a a a a = = = = 2.0 2.5 3.5 5.0 mm mm mm mm Please read Cautions and warnings and Important notes at the end of this document. 12 08/08 Single-ended capacitors Low impedance – 105 °C Technical data and ordering codes VR V DC 50 CR 120 Hz 20 °C µF 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 Case dimensions d×l mm 5 5 5 5 5 5 5 5 5 5 5 5 6.3 6.3 6.3 6.3 6.3 6.3 8 10 10 10 10 10 10 10 10 12.5 12.5 12.5 12.5 × 11 × 11 × 11 × 11 × 11 × 11 × 11 × 11 × 11 × 11 × 11 × 11 × 11 × 11 × 11 × 11 × 15 × 15 × 11.5 × 12.5 × 16 × 16 × 20 × 20 × 25 × 31.5 × 31.5 × 25 × 25 × 31.5 × 35.5 Zmax 100 kHz 20 °C Ω 7.000 6.000 4.900 4.600 4.200 3.900 3.600 3.200 2.700 2.500 2.300 2.100 1.900 1.500 1.100 1.000 0.900 0.800 0.700 0.600 0.500 0.420 0.350 0.310 0.270 0.220 0.180 0.150 0.120 0.110 0.094 IAC,R 100 kHz 105 °C mA 23 29 37 47 57 68 82 93 116 127 148 157 196 216 241 263 332 361 415 501 623 675 821 893 1045 1203 1305 1441 1506 1682 1853 B41042 Ordering code (composition see below) B41042A6474M*** B41042A6684M*** B41042A6105M*** B41042A6155M*** B41042A6225M*** B41042A6335M*** B41042A6475M*** B41042A6685M*** B41042A6106M*** B41042A6126M*** B41042A6156M*** B41042A6186M*** B41042A6226M*** B41042A6276M*** B41042A6336M*** B41042A6396M*** B41042A6476M*** B41042A6566M*** B41042A6686M*** B41042A6826M*** B41042A6107M*** B41042A6127M*** B41042A6157M*** B41042A6187M*** B41042A6227M*** B41042A6277M*** B41042A6337M*** B41042A6397M*** B41042A6477M*** B41042A6567M*** B41042A6687M*** *** = Version 000 = for 001 = for 002 = for 016 = for 007 = for 006 = for 008 = for standard leads, bulk kinked leads, bulk cut leads, bulk taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, lead lead lead lead spacing spacing spacing spacing a a a a = = = = 2.0 2.5 3.5 5.0 mm mm mm mm Please read Cautions and warnings and Important notes at the end of this document. 13 08/08 Single-ended capacitors Low impedance – 105 °C Technical data and ordering codes VR V DC 50 CR 120 Hz 20 °C µF 820 1000 1200 1500 1800 2200 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 Case dimensions d×l mm 12.5 16 16 16 18 18 5 5 6.3 6.3 6.3 6.3 6.3 6.3 8 10 10 10 10 10 10 10 12.5 12.5 12.5 12.5 12.5 12.5 16 16 16 18 × 40 × 31.5 × 35.5 × 40 × 35.5 × 40 × 11 × 11 × 11 × 11 × 11 × 11 × 15 × 15 × 11.5 × 12.5 × 12.5 × 16 × 20 × 20 × 25 × 31.5 × 20 × 25 × 25 × 31.5 × 35.5 × 40 × 31.5 × 35.5 × 40 × 40 Zmax 100 kHz 20 °C Ω 0.088 0.076 0.072 0.065 0.058 0.050 3.600 3.200 2.800 2.400 2.100 1.900 1.700 1.500 1.200 1.100 0.900 0.800 0.650 0.580 0.520 0.420 0.320 0.280 0.220 0.190 0.160 0.140 0.120 0.110 0.098 0.088 IAC,R 100 kHz 105 °C mA 2017 2123 2264 2411 2463 2562 136 147 185 199 217 242 306 332 367 451 503 605 751 823 954 1113 1142 1345 1421 1623 1785 1952 2053 2223 2374 2511 B41042 Ordering code (composition see below) B41042A6827M*** B41042A6108M*** B41042A6128M*** B41042A6158M*** B41042A6188M*** B41042A6228M*** B41042A8106M*** B41042A8126M*** B41042A8156M*** B41042A8186M*** B41042A8226M*** B41042A8276M*** B41042A8336M*** B41042A8396M*** B41042A8476M*** B41042A8566M*** B41042A8686M*** B41042A8826M*** B41042A8107M*** B41042A8127M*** B41042A8157M*** B41042A8187M*** B41042A8227M*** B41042A8277M*** B41042A8337M*** B41042A8397M*** B41042A8477M*** B41042A8567M*** B41042A8687M*** B41042A8827M*** B41042A8108M*** B41042A8128M*** 63 *** = Version 000 = for 001 = for 002 = for 016 = for 007 = for 006 = for 008 = for standard leads, bulk kinked leads, bulk cut leads, bulk taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, lead lead lead lead spacing spacing spacing spacing a a a a = = = = 2.0 2.5 3.5 5.0 mm mm mm mm Please read Cautions and warnings and Important notes at the end of this document. 14 08/08 Single-ended capacitors Low impedance – 105 °C Technical data and ordering codes VR V DC 80 CR 120 Hz 20 °C µF 4.7 6.8 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 Case dimensions d×l mm 5 5 6.3 6.3 6.3 6.3 6.3 6.3 8 10 10 10 10 10 10 10 10 12.5 12.5 12.5 12.5 12.5 16 16 16 18 18 × 11 × 11 × 11 × 11 × 11 × 11 × 15 × 15 × 11.5 × 12.5 × 12.5 × 16 × 20 × 20 × 25 × 31.5 × 31.5 × 25 × 31.5 × 31.5 × 35.5 × 40 × 31.5 × 35.5 × 40 × 35.5 × 40 Zmax 100 kHz 20 °C Ω 8.500 5.500 3.800 3.400 3.000 2.600 2.200 2.000 1.800 1.600 1.300 1.200 1.000 0.850 0.700 0.620 0.550 0.450 0.350 0.300 0.240 0.200 0.170 0.150 0.130 0.120 0.100 IAC,R 100 kHz 105 °C mA 92 111 152 164 189 205 226 256 307 381 410 510 636 676 839 1032 1070 1115 1433 1509 1693 1828 1902 2080 2313 2357 2518 B41042 Ordering code (composition see below) B41042A0475M*** B41042A0685M*** B41042A0106M*** B41042A0126M*** B41042A0156M*** B41042A0186M*** B41042A0226M*** B41042A0276M*** B41042A0336M*** B41042A0396M*** B41042A0476M*** B41042A0566M*** B41042A0686M*** B41042A0826M*** B41042A0107M*** B41042A0127M*** B41042A0157M*** B41042A0187M*** B41042A0227M*** B41042A0277M*** B41042A0337M*** B41042A0397M*** B41042A0477M*** B41042A0567M*** B41042A0687M*** B41042A0827M*** B41042A0108M*** *** = Version 000 = for 001 = for 002 = for 016 = for 007 = for 006 = for 008 = for standard leads, bulk kinked leads, bulk cut leads, bulk taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, lead lead lead lead spacing spacing spacing spacing a a a a = = = = 2.0 2.5 3.5 5.0 mm mm mm mm Please read Cautions and warnings and Important notes at the end of this document. 15 08/08 Single-ended Single-ended capacitors Taping, packing and lead configurations Taping, packing and lead configurations of single-ended capacitors B41042 Single-ended capacitors are available taped in Ammo pack from diameter 4 to 10 mm as follows: Lead spacing 2.0 mm (∅ d = 4 ... 5 mm) Last 3 digits of ordering code: 016 ød P P0 ∆h ∆h H H0 W2 D0 1 max. W1 View B W W0 Base tape Adhesive tape F P1 B l1 t KAL1138-D-E Dimensions in mm ∅d F –0.2 H 18.5 W 18.0 W0 7.0 min. W1 9.0 ± 0.5 W2 3.0 max. P 12.7 ± 1.0 P0 12.7 ± 0.3 P1 5.10 ± 0.7 l1 1.0 max. t 0.7 ± 0.2 ∆h 1 ± 1.0 D0 4.0 ± 0.2 4 ... 5 2.0 ± 0.75 ± 0.5 Please read Cautions and warnings and Important notes at the end of this document. 16 08/08 Single-ended capacitors Taping, packing and lead configurations Lead spacing 2.5 mm (∅ d = 4 ... 6.3 mm) Last 3 digits of ordering code: 007 ød P P0 ∆h ∆h B41042 H H0 W2 1 max. W0 W1 View B W Base tape Adhesive tape P1 B l1 F D0 t KAL1074-3-E Dimensions in mm ∅d 4 ... 6.3 F 2.5 H 18.5 H0 W W0 W1 9.0 W2 3.0 P P0 P1 l1 t 0.7 ∆h 0 D0 4.0 16.0 18.0 7.0 12.7 12.7 5.10 1.0 Tolerance –0.2 ± 0.75 ± 0.5 ± 0.5 min. ± 0.5 max. ± 1.0 ± 0.3 ± 0.7 max. ± 0.2 ± 1.0 ± 0.2 Lead spacing 3.5 mm (∅ d = 8 mm) Last 3 digits of ordering code: 006 ød P P0 ∆h ∆h H H0 W2 D0 1 max. W1 View B W W0 Base tape Adhesive tape F P1 B l1 t KAL1138-D-E Dimensions in mm ∅d 8 F 3.5 H 18.5 W W0 W1 9.0 W2 3.0 P P0 P1 l1 t 0.7 ∆h 1 D0 4.0 18.0 10 12.7 12.7 5.10 1.0 Tolerance ± 0.5 ± 0.75 ± 0.5 min. ± 0.5 max. ± 1.0 ± 0.3 ± 0.7 max. ± 0.2 max. ± 0.2 Please read Cautions and warnings and Important notes at the end of this document. 17 08/08 Single-ended capacitors Taping, packing and lead configurations Lead spacing 5.0 mm (∅ d = 4 ... 8 mm) Last 3 digits of ordering code: 008 ød P P0 ∆h ∆h B41042 H H0 W2 1 max. W0 W1 View B W Base tape Adhesive tape P1 B l1 F D0 t KAL1075-B-E Lead spacing 5.0 mm (∅ d = 10 mm) Last 3 digits of ordering code: 008 ød P P0 ∆h ∆h H W2 1 max. W0 W1 View B W Base tape Adhesive tape P1 B l1 F D0 Dimensions in mm ∅d 4 ... 6.3 8 10 Tolerance F 5.0 5.0 5.0 H 18.5 18.5 18.5 H0 16 16 – W W0 W1 9.0 9.0 W2 3.0 3.0 3.0 P P0 P1 L1 t 0.6 0.6 0.6 ∆h 2.0 2.0 2.0 D0 4.0 4.0 4.0 18.0 7.0 18.0 10 12.7 12.7 3.85 1.0 12.7 12.7 3.85 1.0 12.7 12.7 3.85 1.0 18.0 12.5 9.0 +0.6 ± 0.75 ± 0.5 +1.0 +1.0 ± 0.5 max. ± 0.5 ± 0.3 ± 0.7 max. +0.3 max. ± 0.2 –0.2 –0.5 –0 –0.2 Taping is available up to dimensions d × l = 10 × 20 mm. For ∅ 12.5, 16 and 18 mm taping is not available. Please read Cautions and warnings and Important notes at the end of this document. 18 08/08 t KAL1076-J-E Single-ended capacitors Taping, packing and lead configurations Kinked or cut leads B41042 Single-ended capacitors are available with kinked or cut leads. Other lead configurations also available on request. Kinked leads Last 3 digits of ordering code: 001 l 2.1±0.1 3.2±0.1 KAL1137-5 l ød 4.5±0.5 KAL1084-A Case size d × l (mm) 4×7 5×7 5 × 11 6.3 × 7 6.3 × 11 6.3 × 15 8×7 8 × 11.5 8 × 15 8 × 20 10 × 12.5 10 × 16 10 × 20 10 × 25 10 × 31.5 a 1.2±0.1 ød a (mm) 1.5 2.0 2.0 2.5 2.5 2.5 3.5 3.5 3.5 3.5 5.0 5.0 5.0 5.0 5.0 Case size d × l (mm) a (mm) 12.5 × 16 12.5 × 20 12.5 × 25 12.5 × 31.5 12.5 × 35.5 12.5 × 40 16 × 20 16 × 25 16 × 31.5 16 × 35.5 16 × 40 18 × 20 18 × 25 18 × 31.5 18 × 35.5 18 × 40 5.0 5.0 5.0 5.0 5.0 5.0 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 Please read Cautions and warnings and Important notes at the end of this document. 19 08/08 Single-ended capacitors Taping, packing and lead configurations Cut leads Last 3 digits of ordering code: 002 l B41042 ød 4.5±0.5 KAL1086-R Case size d × l (mm) 4×7 5×7 5 × 11 6.3 × 7 6.3 × 11 6.3 × 15 8×7 8 × 11.5 8 × 15 8 × 20 10 × 12.5 10 × 16 10 × 20 10 × 25 10 × 31.5 a a (mm) 1.5 2.0 2.0 2.5 2.5 2.5 3.5 3.5 3.5 5.0 5.0 5.0 5.0 5.0 5.0 Case size d × l (mm) a (mm) 12.5 × 16 12.5 × 20 12.5 × 25 12.5 × 31.5 12.5 × 35.5 12.5 × 40 16 × 20 16 × 25 16 × 31.5 16 × 35.5 16 × 40 18 × 20 18 × 25 18 × 31.5 18 × 35.5 18 × 40 5.0 5.0 5.0 5.0 5.0 5.0 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 Please read Cautions and warnings and Important notes at the end of this document. 20 08/08 Cautions and warnings General Also see “Important notes” on page 23. 1 Aluminum electrolytic capacitors have a bi-polar structure. This is marked on the body of the capacitor. A capacitor must not be mounted with reversed polarity. The application of an AC or reverse voltage may cause a short circuit or damage the capacitor. Bi-polar capacitors must not be used in AC applications, where the polarity may be reversed in the circuits or is unknown. The DC voltage applied to the capacitor terminal must not exceed its rated operating voltage, as this will result in a rapid increase of the leakage current and may damage the capacitor. It is recommended to operate the capacitor at 70–80% of its rated voltage to optimize its service life. The ripple current applied to the capacitor must be within the permitted range. An excessive ripple current leads to impaired electrical properties and may damage the capacitor. Note that the sum of the peak values of the ripple voltage and the DC operating voltage must not exceed the rated DC voltage. Capacitors must be used within their permitted range of operating temperature. Operation at room temperature optimizes their service life. Capacitors with case diameter ≥ 8 mm are equipped with a safety vent. In capacitors fitted with a lead or soldering lug, the safety vent is usually located at the base of the case. It needs sufficient space around it to operate optimally. The following dimensions are recommended: for case diameter d = 8 to 16 mm, more than 2 mm; for d =18 to 35 mm, more than 3 mm; and for d = 42 mm or more, more than 5 mm. Capacitors should not be mounted with the safety vent face down on the board. Do not locate any wire or copper trace near the safety vent. Do not reverse the voltage, as this may result in excess pressure and the leakage of electrolyte. Gas is released through the safety vent when the pressure inside the capacitor is too high. A gaseous liquid around the safety vent does not indicate a leakage of electrolyte. The capacitor should be stored under conditions of normal temperature and in a non-acid, non-alkali environment of normal humidity. Exposure to high temperatures, for example under direct sunlight, will reduce its operating life. If the capacitor is stored in an environment containing acids or alkalis, the solderability of the leads may be affected. The leakage current of an aluminum electrolytic capacitor may increase after a long period of storage. After such storage, the capacitor must be aged by applying the rated operating voltage for 6–8 hours before use. Manual soldering: a Soldering must be performed within the specified conditions. Bit temperature: 350 °C; application time of soldering iron: 3 seconds. b Ensure that the soldering iron does not touch any part of the capacitor body. 2 3 4 5 6 7 8 9 10 Please read Cautions and warnings and Important notes at the end of this document. 21 08/08 Cautions and warnings 11 Do not apply excessive force to the leads and terminals. Do not move the capacitor after soldering it onto the PC board and do not carry the PC board by gripping the capacitor. Observe the following rules to prevent undue stress to the capacitor: a Do not tilt or bend the capacitor after soldering. b Ensure that the terminal spacing matches the corresponding hole spacing on the PC board. 12 The aluminum case is not insulated from the cathode. Do not place a conductor under the aluminum capacitors on the PC board as this may cause a short circuit. The case and top of capacitors used in switched mode power supplies have a high-voltage-resistant heat shrink sleeve to ensure safe usage. The leads of capacitors with a case diameter exceeding 14 mm cannot be used for fixing. 13 Please read Cautions and warnings and Important notes at the end of this document. 22 08/08 Important notes Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSSP, CTVS, DSSP, MiniBlue, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. 23 08/08