B43044

AEC-C_B41044_B43044.book Seite 1 Dienstag, 5. August 2008 4:13 16 Aluminum electrolytic capacitors Alu-X product lines Single-ended capacitors Series/Type: Data Sheet Date: B41044, B43044 August 2008 © EPCOS AG 2008. Reproduction, publication and dissemination of this publication and the information contained therein without EPCOS’ prior express consent is prohibited. AEC-C_B41044_B43044.book Seite 2 Dienstag, 5. August 2008 4:13 16 Long-life grade capacitors for professional applications Applications ■ Professional switch mode power supplies Features ■ ■ ■ ■ ■ RoHS-compatible High C/V value Very low impedance at high frequencies High reliability Load life of 5000 h at 105 °C Single-ended capacitors Very low impedance – 105 °C Single-ended capacitors Very low impedance – 105 °C B41044, B43044 B41044, B43044 Construction ■ ■ ■ ■ ■ Radial leads Aluminum case, fully insulated Charge-discharge proof Minus pole marking on the insulating sleeve Case with safety vent from diameter 8 mm Delivery mode ■ ■ ■ ■ Bulk Taped, Ammo pack Cut Kinked Please read Cautions and warnings and Important notes at the end of this document. 2 08/08 AEC-C_B41044_B43044.book Seite 3 Dienstag, 5. August 2008 4:13 16 Single-ended capacitors Very low impedance – 105 °C Specifications and characteristics in brief Rated voltage VR Operating temperature range Rated capacitance CR (20 °C, 120 Hz) Capacitance tolerance Load life (105 °C, VR, IAC,R) 6.3 … 450 V DC VR < 350 V DC: –40 °C … +105 °C VR ≥ 350 V DC: –25 °C … +105 °C 0.22 … 15000 µF ± 20% M VR ≤ 100 V DC 2000 h for d = 5 ... 6.3 mm 3000 h for d = 8 mm 5000 h for d ≥ 10 mm B41044, B43044 VR > 100 V DC 2000 h Leakage current Ileak VR ≤ 100 V DC leak Requirements: ∆C/C ≤ ± 20% of initial value tan δ ≤ 2 times initial specified value Ileak ≤ initial specified limit VR > 100 V DC CR VR I leak ≤ 0.02 µA ⋅ ⎛ ------- ⋅ ------ ⎞ +15 µA ⎝ µF V ⎠ (20 °C, after 5 minutes) CR VR ≤ 0.03 µA ⋅ ⎛ ------- ⋅ ------ ⎞ or 4 µA ⎝ µF V ⎠ Dissipation factor (max.) (20 °C, 120 Hz) Low temperature stability (impedance ratio) (120 Hz) 160 350 … … 315 450 tan δ 0.22 0.19 0.16 0.14 0.12 0.10 0.09 0.08 0.15 0.20 For capacitance higher than 1000 µF add 0.02 for every increase of 1000 µF. VR (V DC) 6.3 10 16 25 ... 100 160 ... 250 315 ... 450 4 3 2 2 3 8 Z ( – 25 °C ) -------------------------Z ( +20 °C ) 25 35 50 63 100 8 6 4 3 4 – Z ( – 40 °C ) -------------------------Z ( +20 °C ) After storage for 1000 h at 105 °C, the capacitors shall meet the requirement of load life test after reforming process. After test: VR to be applied for 30 minutes, 24 to 48 hours before measurement. whichever is greater (20 °C, after 1 minute) VR 6.3 10 16 (V DC) Shelf life Please read Cautions and warnings and Important notes at the end of this document. 3 08/08 AEC-C_B41044_B43044.book Seite 4 Dienstag, 5. August 2008 4:13 16 Single-ended capacitors Very low impedance – 105 °C Specifications and characteristics in brief 50 ... 60 Hz 0.47 … 10 µF – 22 … 33 µF – 47 … 330 µF – 470 … 1000 µF – 2200 ... 15000 µF – Voltage range 0.40 160 ... 450 V DC Temperature multiplier +70 °C for rated ripple current 6.3 ... 100 V DC 2.0 160 ... 450 V DC 1.8 Frequency multiplier Voltage range for rated ripple current 6.3 ... 100 V DC 120 Hz 0.42 0.55 0.70 0.75 0.80 0.50 Frequency 1 kHz 0.60 0.75 0.85 0.90 0.95 0.75 +85 °C 1.7 1.4 B41044, B43044 10 kHz 0.80 0.90 0.95 0.98 1.00 0.90 100 kHz 1.00 1.00 1.00 1.00 1.00 1.00 +105 °C 1.0 1.0 Please read Cautions and warnings and Important notes at the end of this document. 4 08/08 AEC-C_B41044_B43044.book Seite 5 Dienstag, 5. August 2008 4:13 16 Single-ended capacitors Very low impedance – 105 °C Dimensional drawing B41044, B43044 d l + 15 min. 5 min. KAL1080-C-E Minus pole marking a Safety vent Safety vent for diameter ≥ 8 mm. Case dimensions d×l mm 5 8 8 8 10 10 10 × 11 × 11.5 × 15 × 20 × 12.5 × 16 × 20 6.3 × 11 dmax × Imax mm 5.5 × 12.5 6.8 × 12.5 8.5 × 13.0 8.5 × 16.5 8.5 × 21.5 11.0 × 14.0 11.0 × 17.5 11.0 × 22.0 13.5 × 22.0 13.5 × 27.0 17.0 × 22.0 17.0 × 27.0 17.0 × 33.5 17.0 × 37.5 19.0 × 22.0 19.0 × 27.0 19.0 × 33.5 19.0 × 37.5 19.0 × 42.0 a mm 2.0 ± 0.5 2.5 ± 0.5 3.5 ± 0.5 3.5 ± 0.5 3.5 ± 0.5 5.0 ± 0.5 5.0 ± 0.5 5.0 ± 0.5 5.0 ± 0.5 5.0 ± 0.5 7.5 ± 0.5 7.5 ± 0.5 7.5 ± 0.5 7.5 ± 0.5 7.5 ± 0.5 7.5 ± 0.5 7.5 ± 0.5 7.5 ± 0.5 7.5 ± 0.5 b mm 0.5 ± 0.1 0.5 ± 0.1 0.6 ± 0.1 0.6 ± 0.1 0.6 ± 0.1 0.6 ± 0.1 0.6 ± 0.1 0.6 ± 0.1 0.6 ± 0.1 0.6 ± 0.1 0.8 ± 0.1 0.8 ± 0.1 0.8 ± 0.1 0.8 ± 0.1 0.8 ± 0.1 0.8 ± 0.1 0.8 ± 0.1 0.8 ± 0.1 0.8 ± 0.1 12.5 × 20 12.5 × 25 16 16 16 16 18 18 18 18 18 × 20 × 25 × 31.5 × 35.5 × 20 × 25 × 31.5 × 35.5 × 40 Please read Cautions and warnings and Important notes at the end of this document. 5 øb 08/08 AEC-C_B41044_B43044.book Seite 6 Dienstag, 5. August 2008 4:13 16 Single-ended capacitors Very low impedance – 105 °C Overview of available types B41044 VR (V DC) CR (µF) 4.7 10 22 33 47 100 150 220 330 470 680 1000 1500 2200 3300 4700 6800 10000 15000 5 5 5 5 × 11 × 11 × 11 × 11 5 5 5 5 × 11 × 11 × 11 × 11 5 5 5 5 × 11 × 11 × 11 × 11 6.3 Case dimensions d × l (mm) 10 16 B41044, B43044 25 5 5 5 5 5 8 8 10 10 10 × 11 × 11 × 11 × 11 × 11 × 11.5 × 11.5 × 12.5 × 16 × 20 × 20 × 25 × 31.5 × 35.5 6.3 × 11 6.3 × 11 8 8 10 10 10 × 11.5 × 11.5 × 12.5 × 16 × 20 6.3 × 11 6.3 × 11 6.3 × 11 6.3 × 11 8 10 10 10 × 11.5 × 12.5 × 12.5 × 20 6.3 × 11 6.3 × 11 8 8 10 10 10 × 11.5 × 11.5 × 12.5 × 16 × 20 12.5 × 20 16 16 16 18 12.5 × 20 12.5 × 25 16 16 18 × 25 × 31.5 × 35.5 12.5 × 20 12.5 × 20 16 16 16 16 × 25 × 25 × 31.5 × 35.5 12.5 × 20 12.5 × 25 16 16 16 × 25 × 31.5 × 35.5 Please read Cautions and warnings and Important notes at the end of this document. 6 08/08 AEC-C_B41044_B43044.book Seite 7 Dienstag, 5. August 2008 4:13 16 Single-ended capacitors Very low impedance – 105 °C Overview of available types B41044 VR (V DC) CR (µF) 0.22 0.47 1.0 2.2 3.3 4.7 10 22 33 47 100 150 220 330 470 680 1000 1500 2200 3300 5 5 5 5 8 8 10 10 10 × 11 × 11 × 11 × 11 × 11.5 × 11.5 × 12.5 × 16 × 20 5 5 5 5 5 5 5 5 8 8 10 10 10 × 11 × 11 × 11 × 11 × 11 × 11 × 11 × 11 × 11.5 × 11.5 × 12.5 × 16 × 20 5 5 5 × 11 × 11 × 11 35 Case dimensions d × l (mm) 50 63 B41044, B43044 100 5 5 5 8 10 10 × 11 × 11 × 11 × 11.5 × 12.5 × 16 6.3 × 11 6.3 × 11 6.3 × 11 8 10 10 10 16 16 16 × 11.5 × 16 × 20 × 25 × 20 × 25 × 35.5 6.3 × 11 6.3 × 11 12.5 × 20 12.5 × 25 16 16 18 × 25 × 31.5 × 40 12.5 × 20 12.5 × 20 12.5 × 25 16 16 18 × 25 × 31.5 × 35.5 12.5 × 20 12.5 × 25 16 16 18 × 25 × 31.5 × 35.5 Please read Cautions and warnings and Important notes at the end of this document. 7 08/08 AEC-C_B41044_B43044.book Seite 8 Dienstag, 5. August 2008 4:13 16 Single-ended capacitors Very low impedance – 105 °C Overview of available types B43044 VR (V DC) CR (µF) 10 22 33 47 68 100 150 220 330 10 10 × 20 × 20 10 × 20 12.5 × 20 12.5 × 20 12.5 × 25 16 18 18 × 25 × 25 × 31.5 10 160 Case dimensions d × l (mm) 200 B41044, B43044 250 × 20 12.5 × 20 12.5 × 25 12.5 × 25 16 16 18 18 × 25 × 31.5 × 31.5 × 40 12.5 × 20 12.5 × 20 16 16 16 18 × 25 × 31.5 × 31.5 × 31.5 VR (V DC) CR (µF) 3.3 4.7 10 22 33 47 68 100 10 16 16 16 18 350 Case dimensions d × l (mm) 400 450 10 × 20 × 20 × 25 × 31.5 × 31.5 10 16 16 18 18 × 20 × 25 × 25 × 31.5 × 40 × 20 12.5 × 20 12.5 × 25 16 16 18 18 × 25 × 31.5 × 31.5 × 35.5 12.5 × 20 12.5 × 25 Please read Cautions and warnings and Important notes at the end of this document. 8 08/08 AEC-C_B41044_B43044.book Seite 9 Dienstag, 5. August 2008 4:13 16 Single-ended capacitors Very low impedance – 105 °C Technical data and ordering codes B41044 VR V DC 6.3 CR 120 Hz 20 °C µF 22 33 47 100 150 220 330 470 680 1000 1500 2200 3300 4700 6800 10000 15000 22 33 47 100 150 220 330 470 680 1000 1500 2200 3300 4700 6800 10000 Case dimensions d×l mm 5 5 5 5 6.3 6.3 6.3 8 10 10 10 12.5 12.5 16 16 16 16 5 5 5 5 6.3 6.3 8 8 10 10 10 12.5 12.5 16 16 16 × 11 × 11 × 11 × 11 × 11 × 11 × 11 × 11.5 × 12.5 × 12.5 × 20 × 20 × 20 × 25 × 25 × 31.5 × 35.5 × 11 × 11 × 11 × 11 × 11 × 11 × 11.5 × 11.5 × 12.5 × 16 × 20 × 20 × 25 × 25 × 31.5 × 35.5 Zmax 100 kHz 20 °C Ω 0.700 0.700 0.650 0.650 0.300 0.300 0.300 0.140 0.100 0.100 0.054 0.050 0.050 0.030 0.030 0.025 0.022 0.700 0.700 0.650 0.650 0.300 0.300 0.140 0.140 0.100 0.080 0.054 0.050 0.038 0.030 0.025 0.022 IAC,R 100 kHz 105 °C mA 180 180 180 180 280 280 280 450 660 660 1100 1400 1400 2100 2100 2600 3000 180 180 180 180 280 280 450 450 660 850 1100 1400 1700 2100 2600 3000 B41044, B43044 Ordering code (composition see below) B41044A2226M*** B41044A2336M*** B41044A2476M*** B41044A2107M*** B41044A2157M*** B41044A2227M*** B41044A2337M*** B41044A2477M*** B41044A2687M*** B41044A2108M*** B41044A2158M*** B41044A2228M*** B41044A2338M*** B41044A2478M*** B41044A2688M*** B41044A2109M*** B41044A2159M*** B41044A3226M*** B41044A3336M*** B41044A3476M*** B41044A3107M*** B41044A3157M*** B41044A3227M*** B41044A3337M*** B41044A3477M*** B41044A3687M*** B41044A3108M*** B41044A3158M*** B41044A3228M*** B41044A3338M*** B41044A3478M*** B41044A3688M*** B41044A3109M*** 10 *** = Version 000 = for 001 = for 002 = for 016 = for 007 = for 006 = for 008 = for standard leads, bulk kinked leads, bulk cut leads, bulk taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, lead lead lead lead spacing spacing spacing spacing a a a a = = = = 2.0 2.5 3.5 5.0 mm mm mm mm Please read Cautions and warnings and Important notes at the end of this document. 9 08/08 AEC-C_B41044_B43044.book Seite 10 Dienstag, 5. August 2008 4:13 16 Single-ended capacitors Very low impedance – 105 °C Technical data and ordering codes B41044 VR V DC 16 CR 120 Hz 20 °C µF 10 22 33 47 100 150 220 330 470 680 1000 1500 2200 3300 4700 6800 4.7 10 22 33 47 100 150 220 330 470 680 1000 1500 2200 3300 4700 for for for for for for for B41044, B43044 Case dimensions d×l mm 5 5 5 5 6.3 6.3 8 8 10 10 10 12.5 12.5 16 16 18 5 5 5 5 5 6.3 8 8 10 10 10 12.5 16 16 16 18 × 11 × 11 × 11 × 11 × 11 × 11 × 11.5 × 11.5 × 12.5 × 16 × 20 × 20 × 25 × 25 × 31.5 × 35.5 × 11 × 11 × 11 × 11 × 11 × 11 × 11.5 × 11.5 × 12.5 × 16 × 20 × 20 × 20 × 25 × 31.5 × 35.5 Zmax 100 kHz 20 °C Ω 0.70 0.70 0.70 0.65 0.30 0.30 0.14 0.14 0.10 0.080 0.054 0.050 0.038 0.030 0.025 0.022 0.70 0.70 0.70 0.70 0.65 0.30 0.14 0.14 0.10 0.080 0.054 0.050 0.030 0.030 0.025 0.022 IAC,R 100 kHz 105 °C mA 180 180 180 180 280 280 450 450 660 850 1100 1400 1700 2100 2600 3000 180 180 180 180 180 280 450 450 660 850 1100 1400 2100 2100 2600 3000 Ordering code (composition see below) B41044A4106M*** B41044A4226M*** B41044A4336M*** B41044A4476M*** B41044A4107M*** B41044A4157M*** B41044A4227M*** B41044A4337M*** B41044A4477M*** B41044A4687M*** B41044A4108M*** B41044A4158M*** B41044A4228M*** B41044A4338M*** B41044A4478M*** B41044A4688M*** B41044A5475M*** B41044A5106M*** B41044A5226M*** B41044A5336M*** B41044A5476M*** B41044A5107M*** B41044A5157M*** B41044A5227M*** B41044A5337M*** B41044A5477M*** B41044A5687M*** B41044A5108M*** B41044A5158M*** B41044A5228M*** B41044A5338M*** B41044A5478M*** 25 *** =Version 000 = 001 = 002 = 016 = 007 = 006 = 008 = standard leads, bulk kinked leads, bulk cut leads, bulk taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, lead lead lead lead spacing spacing spacing spacing a a a a = = = = 2.0 2.5 3.5 5.0 mm mm mm mm Please read Cautions and warnings and Important notes at the end of this document. 10 08/08 AEC-C_B41044_B43044.book Seite 11 Dienstag, 5. August 2008 4:13 16 Single-ended capacitors Very low impedance – 105 °C Technical data and ordering codes B41044 VR V DC 35 CR 120 Hz 20 °C µF 4.7 10 22 33 47 100 150 220 330 470 680 1000 1500 2200 3300 0.22 0.47 1.0 2.2 3.3 4.7 10 22 33 47 100 150 220 330 470 680 1000 1500 2200 Case dimensions d×l mm 5 5 5 5 6.3 8 8 10 10 10 12.5 12.5 16 16 18 5 5 5 5 5 5 5 5 6.3 8 8 10 10 10 12.5 12.5 16 16 18 × 11 × 11 × 11 × 11 × 11 × 11.5 × 11.5 × 12.5 × 16 × 20 × 20 × 25 × 25 × 31.5 × 35.5 × 11 × 11 × 11 × 11 × 11 × 11 × 11 × 11 × 11 × 11.5 × 11.5 × 12.5 × 16 × 20 × 20 × 25 × 25 × 31.5 × 35.5 Zmax 100 kHz 20 °C Ω 0.70 0.70 0.70 0.65 0.30 0.14 0.14 0.10 0.080 0.054 0.050 0.038 0.030 0.025 0.022 8.0 5.0 3.5 3.0 2.6 2.3 1.4 1.2 0.60 0.43 0.35 0.17 0.20 0.10 0.085 0.065 0.043 0.038 0.034 IAC,R 100 kHz 105 °C mA 180 180 180 180 280 450 450 660 850 1100 1400 1700 2100 2600 3000 18 25 40 55 65 90 120 150 200 250 340 490 650 810 1100 1200 1600 2000 2300 B41044, B43044 Ordering code (composition see below) B41044A7475M*** B41044A7106M*** B41044A7226M*** B41044A7336M*** B41044A7476M*** B41044A7107M*** B41044A7157M*** B41044A7227M*** B41044A7337M*** B41044A7477M*** B41044A7687M*** B41044A7108M*** B41044A7158M*** B41044A7228M*** B41044A7338M*** B41044A6224M*** B41044A6474M*** B41044A6105M*** B41044A6225M*** B41044A6335M*** B41044A6475M*** B41044A6106M*** B41044A6226M*** B41044A6336M*** B41044A6476M*** B41044A6107M*** B41044A6157M*** B41044A6227M*** B41044A6337M*** B41044A6477M*** B41044A6687M*** B41044A6108M*** B41044A6158M*** B41044A6228M*** 50 *** = Version 000 = for 001 = for 002 = for 016 = for 007 = for 006 = for 008 = for standard leads, bulk kinked leads, bulk cut leads, bulk taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, lead lead lead lead spacing spacing spacing spacing a a a a = = = = 2.0 2.5 3.5 5.0 mm mm mm mm Please read Cautions and warnings and Important notes at the end of this document. 11 08/08 AEC-C_B41044_B43044.book Seite 12 Dienstag, 5. August 2008 4:13 16 Single-ended capacitors Very low impedance – 105 °C Technical data and ordering codes B41044 VR V DC 63 CR 120 Hz 20 °C µF 3.3 4.7 10 22 33 47 100 150 220 330 470 680 1000 2.2 3.3 4.7 10 22 33 47 100 150 220 330 470 Case dimensions d×l mm 5 5 5 6.3 6.3 8 10 10 10 12.5 16 16 16 5 5 5 6.3 8 10 10 12.5 12.5 16 16 18 × 11 × 11 × 11 × 11 × 11 × 11.5 × 16 × 20 × 25 × 20 × 20 × 25 × 35.5 × 11 × 11 × 11 × 11 × 11.5 × 12.5 × 16 × 20 × 25 × 25 × 31.5 × 40 Zmax 100 kHz 20 °C Ω 2.0 2.0 2.0 0.60 0.60 0.50 0.12 0.10 0.090 0.085 0.050 0.043 0.025 2.5 2.5 2.5 1.0 0.60 0.40 0.30 0.15 0.12 0.070 0.050 0.030 IAC,R 100 kHz 105 °C mA 64 76 111 190 233 328 456 610 809 1036 1411 1843 1967 52 64 76 128 224 319 417 570 762 1048 1404 1980 B41044, B43044 Ordering code (composition see below) B41044A8335M*** B41044A8475M*** B41044A8106M*** B41044A8226M*** B41044A8336M*** B41044A8476M*** B41044A8107M*** B41044A8157M*** B41044A8227M*** B41044A8337M*** B41044A8477M*** B41044A8687M*** B41044A8108M*** B41044A9225M*** B41044A9335M*** B41044A9475M*** B41044A9106M*** B41044A9226M*** B41044A9336M*** B41044A9476M*** B41044A9107M*** B41044A9157M*** B41044A9227M*** B41044A9337M*** B41044A9477M*** 100 *** = Version 000 = for 001 = for 002 = for 016 = for 007 = for 006 = for 008 = for standard leads, bulk kinked leads, bulk cut leads, bulk taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, lead lead lead lead spacing spacing spacing spacing a a a a = = = = 2.0 2.5 3.5 5.0 mm mm mm mm Please read Cautions and warnings and Important notes at the end of this document. 12 08/08 AEC-C_B41044_B43044.book Seite 13 Dienstag, 5. August 2008 4:13 16 Single-ended capacitors Very low impedance – 105 °C Technical data and ordering codes B43044 VR V DC 160 CR 120 Hz 20 °C µF 22 33 47 68 100 150 220 330 22 33 47 68 100 150 220 10 22 33 47 68 100 150 220 10 22 33 47 68 100 Case dimensions d×l mm 10 10 12.5 12.5 16 16 16 18 10 12.5 12.5 12.5 16 18 18 10 12.5 12.5 12.5 16 16 18 18 10 12.5 16 16 16 18 × 20 × 20 × 20 × 20 × 25 × 31.5 × 31.5 × 31.5 × 20 × 20 × 20 × 25 × 25 × 25 × 31.5 × 20 × 20 × 25 × 25 × 25 × 31.5 × 31.5 × 40 × 20 × 20 × 20 × 25 × 31.5 × 31.5 Zmax 100 kHz 20 °C Ω 1.3 1.3 0.91 0.63 0.27 0.22 0.22 0.22 1.5 0.91 0.91 0.63 0.27 0.27 0.22 3.5 2.3 1.7 1.7 0.78 0.63 0.42 0.35 2.9 2.1 0.91 0.73 0.49 0.40 IAC,R 100 kHz 105 °C mA 440 565 725 950 1280 1300 1300 1700 440 590 780 950 1280 1500 1700 300 480 630 630 1000 1400 1450 1485 180 270 600 700 1100 1170 B41044, B43044 Ordering code (composition see below) B43044A1226M*** B43044A1336M*** B43044A1476M*** B43044A1686M*** B43044A1107M*** B43044A1157M*** B43044A1227M*** B43044A1337M*** B43044A2226M*** B43044A2336M*** B43044A2476M*** B43044A2686M*** B43044A2107M*** B43044A2157M*** B43044A2227M*** B43044F2106M*** B43044F2226M*** B43044F2336M*** B43044F2476M*** B43044F2686M*** B43044F2107M*** B43044F2157M*** B43044F2227M*** B43044A4106M*** B43044A4226M*** B43044A4336M*** B43044A4476M*** B43044A4686M*** B43044A4107M*** 200 250 350 *** = Version 000 = for 001 = for 002 = for 016 = for 007 = for 006 = for 008 = for standard leads, bulk kinked leads, bulk cut leads, bulk taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, lead lead lead lead spacing spacing spacing spacing a a a a = = = = 2.0 2.5 3.5 5.0 mm mm mm mm Please read Cautions and warnings and Important notes at the end of this document. 13 08/08 AEC-C_B41044_B43044.book Seite 14 Dienstag, 5. August 2008 4:13 16 Single-ended capacitors Very low impedance – 105 °C Technical data and ordering codes B43044 VR V DC 400 CR 120 Hz 20 °C µF 10 22 33 47 68 100 3.3 4.7 10 22 33 47 68 Case dimensions d×l mm 10 12.5 16 16 18 18 10 12.5 12.5 16 16 18 18 × 20 × 25 × 25 × 25 × 31.5 × 40 × 20 × 20 × 25 × 25 × 31.5 × 31.5 × 35.5 Zmax 100 kHz 20 °C Ω 2.9 1.3 0.91 0.73 0.49 0.34 6.5 3.6 2.5 1.7 1.1 0.93 0.71 IAC,R 100 kHz 105 °C mA 180 300 600 700 1100 1250 150 200 315 570 620 900 980 B41044, B43044 Ordering code (composition see below) B43044A9106M*** B43044A9226M*** B43044A9336M*** B43044A9476M*** B43044A9686M*** B43044A9107M*** B43044A5335M*** B43044A5475M*** B43044A5106M*** B43044A5226M*** B43044A5336M*** B43044A5476M*** B43044A5686M*** 450 *** = Version 000 = for 001 = for 002 = for 016 = for 007 = for 006 = for 008 = for standard leads, bulk kinked leads, bulk cut leads, bulk taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, taped leads, Ammo pack, lead lead lead lead spacing spacing spacing spacing a a a a = = = = 2.0 2.5 3.5 5.0 mm mm mm mm Please read Cautions and warnings and Important notes at the end of this document. 14 08/08 AEC-C_B41044_B43044.book Seite 15 Dienstag, 5. August 2008 4:13 16 Single-ended Single-ended capacitors Taping, packing and lead configurations Taping, packing and lead configurations of single-ended capacitors B41044, B43044 Single-ended capacitors are available taped in Ammo pack from diameter 4 to 10 mm as follows: Lead spacing 2.0 mm (∅ d = 4 ... 5 mm) Last 3 digits of ordering code: 016 ød P P0 ∆h ∆h H H0 W2 D0 1 max. W1 View B W W0 Base tape Adhesive tape F P1 B l1 t KAL1138-D-E Dimensions in mm ∅d F –0.2 H 18.5 W 18.0 W0 7.0 min. W1 9.0 ± 0.5 W2 3.0 max. P 12.7 ± 1.0 P0 12.7 ± 0.3 P1 5.10 ± 0.7 l1 1.0 max. t 0.7 ± 0.2 ∆h 1 ± 1.0 D0 4.0 ± 0.2 4 ... 5 2.0 ± 0.75 ± 0.5 Please read Cautions and warnings and Important notes at the end of this document. 15 08/08 AEC-C_B41044_B43044.book Seite 16 Dienstag, 5. August 2008 4:13 16 Single-ended capacitors Taping, packing and lead configurations Lead spacing 2.5 mm (∅ d = 4 ... 6.3 mm) Last 3 digits of ordering code: 007 ød P P0 ∆h ∆h B41044, B43044 H H0 W2 1 max. W0 W1 View B W Base tape Adhesive tape P1 B l1 F D0 t KAL1074-3-E Dimensions in mm ∅d 4 ... 6.3 F 2.5 H 18.5 H0 W W0 W1 9.0 W2 3.0 P P0 P1 l1 t 0.7 ∆h 0 D0 4.0 16.0 18.0 7.0 12.7 12.7 5.10 1.0 Tolerance –0.2 ± 0.75 ± 0.5 ± 0.5 min. ± 0.5 max. ± 1.0 ± 0.3 ± 0.7 max. ± 0.2 ± 1.0 ± 0.2 Lead spacing 3.5 mm (∅ d = 8 mm) Last 3 digits of ordering code: 006 ød P P0 ∆h ∆h H H0 W2 D0 1 max. W1 View B W W0 Base tape Adhesive tape F P1 B l1 t KAL1138-D-E Dimensions in mm ∅d 8 F 3.5 H 18.5 W W0 W1 9.0 W2 3.0 P P0 P1 l1 t 0.7 ∆h 1 D0 4.0 18.0 10 12.7 12.7 5.10 1.0 Tolerance ± 0.5 ± 0.75 ± 0.5 min. ± 0.5 max. ± 1.0 ± 0.3 ± 0.7 max. ± 0.2 max. ± 0.2 Please read Cautions and warnings and Important notes at the end of this document. 16 08/08 AEC-C_B41044_B43044.book Seite 17 Dienstag, 5. August 2008 4:13 16 Single-ended capacitors Taping, packing and lead configurations Lead spacing 5.0 mm (∅ d = 4 ... 8 mm) Last 3 digits of ordering code: 008 ød P P0 ∆h ∆h B41044, B43044 H H0 W2 1 max. W0 W1 View B W Base tape Adhesive tape P1 B l1 F D0 t KAL1075-B-E Lead spacing 5.0 mm (∅ d = 10 mm) Last 3 digits of ordering code: 008 ød P P0 ∆h ∆h H W2 1 max. W0 W1 View B W Base tape Adhesive tape P1 B l1 F D0 Dimensions in mm ∅d 4 ... 6.3 8 10 Tolerance F 5.0 5.0 5.0 H 18.5 18.5 18.5 H0 16 16 – W W0 W1 9.0 9.0 W2 3.0 3.0 3.0 P P0 P1 L1 t 0.6 0.6 0.6 ∆h 2.0 2.0 2.0 D0 4.0 4.0 4.0 18.0 7.0 18.0 10 12.7 12.7 3.85 1.0 12.7 12.7 3.85 1.0 12.7 12.7 3.85 1.0 18.0 12.5 9.0 +0.6 ± 0.75 ± 0.5 +1.0 +1.0 ± 0.5 max. ± 0.5 ± 0.3 ± 0.7 max. +0.3 max. ± 0.2 –0.2 –0.5 –0 –0.2 Taping is available up to dimensions d × l = 10 × 20 mm. For ∅ 12.5, 16 and 18 mm taping is not available. Please read Cautions and warnings and Important notes at the end of this document. 17 08/08 t KAL1076-J-E AEC-C_B41044_B43044.book Seite 18 Dienstag, 5. August 2008 4:13 16 Single-ended capacitors Taping, packing and lead configurations Kinked or cut leads B41044, B43044 Single-ended capacitors are available with kinked or cut leads. Other lead configurations also available on request. Kinked leads Last 3 digits of ordering code: 001 l 2.1±0.1 3.2±0.1 KAL1137-5 l ød 4.5±0.5 KAL1084-A Case size d × l (mm) 4×7 5×7 5 × 11 6.3 × 7 6.3 × 11 6.3 × 15 8×7 8 × 11.5 8 × 15 8 × 20 10 × 12.5 10 × 16 10 × 20 10 × 25 10 × 31.5 a 1.2±0.1 ød a (mm) 1.5 2.0 2.0 2.5 2.5 2.5 3.5 3.5 3.5 3.5 5.0 5.0 5.0 5.0 5.0 Case size d × l (mm) a (mm) 12.5 × 16 12.5 × 20 12.5 × 25 12.5 × 31.5 12.5 × 35.5 12.5 × 40 16 × 20 16 × 25 16 × 31.5 16 × 35.5 16 × 40 18 × 20 18 × 25 18 × 31.5 18 × 35.5 18 × 40 5.0 5.0 5.0 5.0 5.0 5.0 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 Please read Cautions and warnings and Important notes at the end of this document. 18 08/08 AEC-C_B41044_B43044.book Seite 19 Dienstag, 5. August 2008 4:13 16 Single-ended capacitors Taping, packing and lead configurations Cut leads Last 3 digits of ordering code: 002 l B41044, B43044 ød 4.5±0.5 KAL1086-R Case size d × l (mm) 4×7 5×7 5 × 11 6.3 × 7 6.3 × 11 6.3 × 15 8×7 8 × 11.5 8 × 15 8 × 20 10 × 12.5 10 × 16 10 × 20 10 × 25 10 × 31.5 a a (mm) 1.5 2.0 2.0 2.5 2.5 2.5 3.5 3.5 3.5 5.0 5.0 5.0 5.0 5.0 5.0 Case size d × l (mm) a (mm) 12.5 × 16 12.5 × 20 12.5 × 25 12.5 × 31.5 12.5 × 35.5 12.5 × 40 16 × 20 16 × 25 16 × 31.5 16 × 35.5 16 × 40 18 × 20 18 × 25 18 × 31.5 18 × 35.5 18 × 40 5.0 5.0 5.0 5.0 5.0 5.0 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 Please read Cautions and warnings and Important notes at the end of this document. 19 08/08 AEC-C_B41044_B43044.book Seite 20 Dienstag, 5. August 2008 4:13 16 Cautions and warnings General Also see “Important notes” on page 22. 1 Aluminum electrolytic capacitors have a bi-polar structure. This is marked on the body of the capacitor. A capacitor must not be mounted with reversed polarity. The application of an AC or reverse voltage may cause a short circuit or damage the capacitor. Bi-polar capacitors must not be used in AC applications, where the polarity may be reversed in the circuits or is unknown. The DC voltage applied to the capacitor terminal must not exceed its rated operating voltage, as this will result in a rapid increase of the leakage current and may damage the capacitor. It is recommended to operate the capacitor at 70–80% of its rated voltage to optimize its service life. The ripple current applied to the capacitor must be within the permitted range. An excessive ripple current leads to impaired electrical properties and may damage the capacitor. Note that the sum of the peak values of the ripple voltage and the DC operating voltage must not exceed the rated DC voltage. Capacitors must be used within their permitted range of operating temperature. Operation at room temperature optimizes their service life. Capacitors with case diameter ≥ 8 mm are equipped with a safety vent. In capacitors fitted with a lead or soldering lug, the safety vent is usually located at the base of the case. It needs sufficient space around it to operate optimally. The following dimensions are recommended: for case diameter d = 8 to 16 mm, more than 2 mm; for d =18 to 35 mm, more than 3 mm; and for d = 42 mm or more, more than 5 mm. Capacitors should not be mounted with the safety vent face down on the board. Do not locate any wire or copper trace near the safety vent. Do not reverse the voltage, as this may result in excess pressure and the leakage of electrolyte. Gas is released through the safety vent when the pressure inside the capacitor is too high. A gaseous liquid around the safety vent does not indicate a leakage of electrolyte. The capacitor should be stored under conditions of normal temperature and in a non-acid, non-alkali environment of normal humidity. Exposure to high temperatures, for example under direct sunlight, will reduce its operating life. If the capacitor is stored in an environment containing acids or alkalis, the solderability of the leads may be affected. The leakage current of an aluminum electrolytic capacitor may increase after a long period of storage. After such storage, the capacitor must be aged by applying the rated operating voltage for 6–8 hours before use. Manual soldering: a Soldering must be performed within the specified conditions. Bit temperature: 350 °C; application time of soldering iron: 3 seconds. b Ensure that the soldering iron does not touch any part of the capacitor body. 2 3 4 5 6 7 8 9 10 Please read Cautions and warnings and Important notes at the end of this document. 20 08/08 AEC-C_B41044_B43044.book Seite 21 Dienstag, 5. August 2008 4:13 16 Cautions and warnings 11 Do not apply excessive force to the leads and terminals. Do not move the capacitor after soldering it onto the PC board and do not carry the PC board by gripping the capacitor. Observe the following rules to prevent undue stress to the capacitor: a Do not tilt or bend the capacitor after soldering. b Ensure that the terminal spacing matches the corresponding hole spacing on the PC board. 12 The aluminum case is not insulated from the cathode. Do not place a conductor under the aluminum capacitors on the PC board as this may cause a short circuit. The case and top of capacitors used in switched mode power supplies have a high-voltage-resistant heat shrink sleeve to ensure safe usage. The leads of capacitors with a case diameter exceeding 14 mm cannot be used for fixing. 13 Please read Cautions and warnings and Important notes at the end of this document. 21 08/08 AEC-C_B41044_B43044.book Seite 22 Dienstag, 5. August 2008 4:13 16 Important notes Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSSP, CTVS, DSSP, MiniBlue, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. 22 08/08