B44020B0006B076

B44020 Accessories KAL0567 B Accessories Accessories for capacitors with mounting stud on capacitor base Capacitor diameter Dimensional drawing Diameter d (mm) Ordering code Insulating plastic shoulder washer “P” similar to DIN 41 331 specifications for M 8 thread ≤ 40 mm 8,4 B44020B0001B025 KAL0216-I for M 12 thread > 40 mm 12,5 B44020B0002B030 KAL0059-P Insulating washer “N” made of laminated paper for M 8 / M 12 thread ≤ 40 mm 8,4 B44020A0001B025 > 40 mm KAL0066-7 13,0 Insulating washer made of Hostalen B44020A0002B025 d 1 – 0,5 d 2 – 0,5 51,6 mm 76,9 mm 51 76 31 56 B44020B0006B051 B44020B0006B076 KAL0061-1 166 10/02 B44020 Accessories KAL0567 B Capacitor diameter Dimensional drawing Plastic cap nut “V” for M 8 thread width across flats 13 mm Ordering code ≤ 40 mm KAL0067-F B44020B0005B008 for M 12 thread width across flats 17 mm > 40 mm B44020A0005B012 KAL0068-N Reinforced nylon cap nut for M 12 thread width across flats 19 mm > 40 mm B44020J0006B012 for M 8 thread width across flats 17 mm ≤ 40 mm B44020J0006B008 KAL0236-X for M 12 width across flats 19 mm > 40 mm thread *) B44020J0007B012 KAL0285-Q *) For achieving larger clearances. 167 10/02 B44020 Accessories KAL0567 B Mounting instructions Maximum tightening torques: Thread M8 M12 Maximum torque 4 10 Nm Nm Non-insulated mounting with cap nut KAL0063-H Insulated mounting with cap nut KAL0064-Q Mounting hole diameter Insulated mounting with DIN 439 hex nut d ≤ 76,9 mm d = 91 mm KAL0065-Y Mounting hole diameter Mounting hole diameter 168 10/02 B44030 Accessories KAL0567 B Ring clip mounting Ring clips are primarily used for upright mounting of screw-terminal and photoflash capacitors. The clip surfaces are specially treated and corrosion-protected. dN Capacitor Mounting plate KAL0193-A A variety of ring clip versions is available for Al electrolytic capacitors. Some versions are supplied with AM 3 × 10 DIN 84 clamping screws and DIN 934 nuts included. Additional insulation can be achieved by inserting a 30 mm-wide insulating strip between the capacitor and the ring clip. In such cases, attention must be paid to any relevant regulations (e. g. VDE, BSA or UL regulations). dN h1 mm h2 Ring clip version Ordering code without with insulating strip 25 19 15 KAL0198-G B44030A0025B B44030J0025B Clamping screws and nuts are included in delivery package. (insulating strip length:175mm) 30 19 15 KAL0199-P B44030A0030B B44030J0030B Clamping screws and nuts are included in delivery package. 169 10/02 (insulating strip length: 200mm) B44030 Accessories KAL0567 B dN h1 mm h2 Ring clip version Ordering code without with insulating strip 19 15 KAL0201-5 B44030A0035B B44030J0035B Clamping screws and nuts are included in delivery package. 35 (insulating strip length: 230mm) 15 10 B44030A0036B B44030J0036B (insulating strip length: 230mm) 40 19 15 KAL0200-W B44030A0040B B44030J0040B Clamping screws and nuts are included in delivery package. 170 10/02 (insulating strip length: 260mm) B44030 Accessories KAL0567 B dN h1 mm h2 Ring clip version Ordering code without with insulating strip 19 15 KAL0194-I B44030A0050B B44030J0050B Clamping screws and nuts are included in delivery package. 50 (insulating strip length: 325mm) 22 15 B44030A0051B B44030J0051B (insulating strip length: 325mm) 65 26 22 B44030A0065B B44030J0065B KAL0203-L Clamping screws and nuts are included in delivery package. 171 10/02 (insulating strip length: 420mm) B44030 Accessories KAL0567 B dN h1 mm h2 Ring clip version Ordering code without with insulating strip 65 29 19 B44030A0064B B44030J0064B (insulating strip length: 420mm) 75 29 19 B44030A0075B B44030J0075B (insulating strip length: 495mm) 90 29 19 B44030A0090B B44030J0090B (insulating strip length: 585mm) 172 10/02 B44030 Accessories KAL0567 B Clamp mounting Screw-terminal capacitors without threaded stud and with a diameter ≥ 64,3 mm can also be mounted with clamps. Clamp mounting offers the following advantages: I Optimum heat transfer between capacitor base and board due to pressure contact I High vibration resistance I Electrically insulated material Dimensional drawing dN Capacitor Fixing part Board Tubular rivet 3) Cylinder screw DIN912-M6x… Section A-B Untightened Tightened Dimensions and ordering codes Capacitor diameter dN 65 mm 75 mm 90 mm d1 ± 0,2 mm 87 99 112 b mm 104 116 130 Ordering code B44030A0165B B44030A0175B B44030A0190B Screws are not included in the delivery package. 1) Lenght depends on application. 2) The screws have to be tightened uniformly and crosswise until the fixing part rests flatly on the board. 3) Tubular rivets included in delivery package. 173 10/02 B44030 Accessories KAL0567 B Mounting set (clamping rings) This mounting set offers following advantages: – – – – Protects the capacitor against tilt Fits for different capacitor length Protects the capacitor terminals from mechanical stress Electrically insulated clamping material Dimensional drawing ø86 ø75 ø101 ø90 43,5 80 45,5 86 ø83 10 ø95,5 ø6 ø5 63.5 57,5 105 120 Clamping ring Dimensions and ordering codes Mounting base plate 12 0˚ 12 Capacitor diameter d N 75 mm 90 mm 174 10/02 ∅min mm 96,5 Ordering code B44030A0375B B44030A0390B KAL0499-8 84 ø min. KAL0499-8 Herausgegeben von EPCOS AG Unternehmenskommunikation, Postfach 80 17 09, 81617 München, DEUTSCHLAND ++49 89 636 09, FAX (0 89) 636-2 26 89 (  EPCOS AG 2002. Vervielfältigung, Veröffentlichung, Verbreitung und Verwertung dieser Broschüre und ihres Inhalts ohne ausdrückliche Genehmigung der EPCOS AG nicht gestattet. Bestellungen unterliegen den vom ZVEI empfohlenen Allgemeinen Lieferbedingungen für Erzeugnisse und Leistungen der Elektroindustrie, soweit nichts anderes vereinbart wird. Diese Broschüre ersetzt die vorige Ausgabe. Fragen über Technik, Preise und Liefermöglichkeiten richten Sie bitte an den Ihnen nächstgelegenen Vertrieb der EPCOS AG oder an unsere Vertriebsgesellschaften im Ausland. Bauelemente können aufgrund technischer Erfordernisse Gefahrstoffe enthalten. Auskünfte darüber bitten wir unter Angabe des betreffenden Typs ebenfalls über die zuständige Vertriebsgesellschaft einzuholen. Published by EPCOS AG Corporate Communications, P.O. Box 80 17 09, 81617 Munich, GERMANY ++49 89 636 09, FAX (0 89) 636-2 26 89  EPCOS AG 2002. Reproduction, publication and dissemination of this brochure and the information contained therein without EPCOS’ prior express consent is prohibited. Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry recommended by the ZVEI (German Electrical and Electronic Manufacturers’ Association), unless otherwise agreed. This brochure replaces the previous edition. For questions on technology, prices and delivery please contact the Sales Offices of EPCOS AG or the international Representatives. Due to technical requirements components may contain dangerous substances. For information on the type in question please also contact one of our Sales Offices. (