B58703M1103A002

NTC thermistors for temperature measurement Probe assemblies Series/Type: Ordering code: M1703 B58703M1103A00* Date: Version: 2019-09-23 2.0 Content of header bars 1 and 2 of data sheet will be automatically entered in headers and footers! Please fill in the table and then change the color to "white". This ensures that the table disappears (invisible) for the customer PDF. Don't change formatting when entering or pasting text in the table and don't add any cell or line in and to it! Identification/Classification 1 NTC thermistors for temperature measurement (header 1 + top left bar): Identification/Classification 2 Probe assemblies (header 2 + bottom left header bar): Ordering code: (top right header bar) B58703M1103A00* Series/Type: (bottom right header bar) M1703 Preliminary data (optional): Department: TPS NTC PD S Date: 2019-09-23 Version: 2.0  TDK Electronics AG 2019. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without TDK Electronics' prior express consent is prohibited. NTC thermistors for temperature measurement Probe assemblies Applications B58703M1103A00* M1703 Dimensional drawing  Busbar temperature measurement Features     Screw-on mounting with good thermal contact Accurate busbar temperature readings HV insulation acc. LV123 Class H3 Wire acc. LV112-4 (0.13 mm² CuMg alloy with reduced weight)  Up to 50 N pull force during installation allowed  Twisted wire for EMC Options  Alternative wire lengths, R/T characteristics and connectors available on request Delivery mode  Bulk, bundled in plastic bags in cardboard box  Cable tie and wire scrap L2 must be removed before sensor installation Dimensions in mm General technical data Climatic category Lower category temperature Upper category temperature Maximum operating temperature Max. power Rated temperature Rated resistance Resistance tolerance1) B-value1) No. of R/T charactericstic Thermal time constant Insulation resistance Test voltage Sensor accuracy2) Sensor accuracy2) (IEC 60068-1) (for 6 h max.) (at 25 °C) τa Rins (t = 60 s) Vtest (-30 °C ≤ T ≤ 150 °C) ∆T (T < -30 °C / T > 150 °C) ∆T (in water) 1) Values for initial glass-encapsulated NTC G1561. 2) Sensor accuracy is criteria for reliability testing. TPS NTC PD S Please read Cautions and warnings and Important notes at the end of this document. Top,max P25 TR RR ∆RR/RR B25/100 40/150/21 –40 150 200 50 25 10000 ±1 3625 ±1% 7003 < 10 100 2500 ±5 ±10 °C °C °C mW °C Ω % K s MΩ V DC K K 2019-09-23 Page 2 of 10 NTC thermistors for temperature measurement Probe assemblies B58703M1103A00* M1703 Wire lengths, units per box and ordering codes Usable wire length L1 mm Wire scrap L23) mm Unit per box pcs. Detailed drawing4) Ordering codes max. 655 min. 45 800 Ind. 06b dated 2017-11-13 B58703M1103A001 max. 1000 min. 45 600 Ind. 04 dated 2017- B58703M1103A002 11-13 Reliability data Test Standard Test conditions Initial RT parameter LV124 – K02 (modified) –40 °C, 25 °C, 85 °C; 150 °C; 200 °C ∆T ±5 K Insulation strength test LV123 H3 1000 V DC for 60 s Riso > 1 GΩ Voltage strength test LV123 H3 2500 V DC for 60 s Ileak < 10 mA No flashover 25 °C water to 85 °C water τa < 10 s No visible damage Response time test Criteria Remarks No visible damage No visible damage ESD test AEC-Q200-002 ISO / DIS 10605 ESD network 2000 Ω, 330 pF Direct contact discharge up to 8 kV Air discharge 25 kV ∆T ± 5 K No visible damage Temperature storage test LV124 K-01 sequence –40 °C for 12 h 150 °C for 12 h 2 cycles (48 h in total) ∆T ± 5 K No visible damage Low temperature operation test LV124 K-01 sequence –40 °C for 48 h in operation ∆T ± 5 K No visible damage Thermal shock LV124 K-05 test sequence –40 °C / 150 °C for 100 cycles dwell time 30 min, transition < 30 s ∆T ± 5 K No visible damage Cyclic damp heat test LV124 K-08 sequence 25 °C / 55 °C, 97% r. H., 6 cycles of 24 h (144 h in total) in operation ∆T ± 5 K No visible damage Mechanical shock test LV124 M-05 sequence Accelaration half sine: 50 g / 6 ms, ∆T ± 5 K 60 shocks (10 shocks in 6 directions) in operation No visible damage 3) Not intended for use, must be removed before sensor installation and operation. 4) On request. TPS NTC PD S Please read Cautions and warnings and Important notes at the end of this document. 2019-09-23 Page 3 of 10 NTC thermistors for temperature measurement Probe assemblies B58703M1103A00* M1703 Test Standard Test conditions Criteria Remarks Vibration test LV124 M-04 sequence (profile D) –40 °C / 125 °C, 5 Hz … 2000 Hz, 4.2 g 8 h per axis (in total 24 h), intermittent operation ∆T ± 5 K No visible damage Damp heat test LV124 K-14 (steady state) 40 °C / 93 % r. H, in operation for 21 days ∆T ± 5 K No visible damage Corrosion test with flow of mixed gas LV124 K-18 SO2 0.2 ppm, H2S 0.01 ppm, NO2 0.2 ppm, Cl2 0.01 ppm, Test duration 21 days ∆T ± 5 K No visible damage Chemical media test LV124-C01 Diesel fuel, petrol/gasoline unleaded, ∆T ± 5 K engine oil, transmission fluid, grease, battery fluid, brake fluid, antifreeze fluid, windscreen washer fluid, vehicle washing chemicals, Test duration 24 h No visible damage High LV124 L-02 temperature endurance test 125 °C for 2000 h, in operation with overvoltage 900 V DC ∆T ± 5 K No visible damage Temperature LV124 L-03 cycle endurance test –40 °C / 125 °C for 140 cycles, dwell ∆T ± 5 K time 30 min., in operation with overvoltage 900 V DC No visible damage Note  NTC element qualified acc. To AEC-Q200 rev. D.  Details of reliability tests on request. TPS NTC PD S Please read Cautions and warnings and Important notes at the end of this document. 2019-09-23 Page 4 of 10 NTC thermistors for temperature measurement Probe assemblies B58703M1103A00* M1703 R/T characteristics R/T No. 7003 T (°C) B25/100 = 3625 K Rnom (Ω) Rmin (Ω) Rmax (Ω) ∆R/Rnom (±%) ∆T (±K) α (%/K) –40 243240 232440 254040 4.4 0.7 6.0 –35 180810 173370 188240 4.1 0.7 5.8 –30 135750 130590 140910 3.8 0.7 5.6 –25 102900 99302 106510 3.5 0.6 5.4 –20 78716 76188 81244 3.2 0.6 5.3 –15 60739 58957 62521 2.9 0.6 5.1 –10 47258 45998 48519 2.7 0.5 4.9 –5 37062 36169 37955 2.4 0.5 4.8 0 29287 28653 29920 2.2 0.5 4.6 5 23311 22862 23759 1.9 0.4 4.5 10 18684 18367 19000 1.7 0.4 4.4 15 15075 14853 15297 1.5 0.3 4.2 20 12240 12087 12394 1.3 0.3 4.1 25 10000 9900 10100 1.0 0.3 4.0 30 8217.6 8114.8 8320.3 1.3 0.3 3.9 35 6790.9 6692.8 6889 1.4 0.4 3.8 40 5642.2 5550.1 5734.3 1.6 0.4 3.7 45 4712.2 4626.7 4797.7 1.8 0.5 3.6 50 3955 3876.3 4033.8 2.0 0.6 3.5 55 3335.5 3263.4 3407.6 2.2 0.6 3.4 60 2826 2760.2 2891.7 2.3 0.7 3.3 65 2404.9 2345 2464.7 2.5 0.8 3.2 70 2055.3 2000.9 2109.6 2.6 0.9 3.1 75 1763.7 1714.4 1813 2.8 0.9 3.0 80 1519.5 1474.7 1564.2 2.9 1.0 2.9 85 1314.1 1273.5 1354.6 3.1 1.1 2.9 90 1140.6 1103.8 1177.4 3.2 1.2 2.8 95 993.52 960.12 1026.9 3.4 1.2 2.7 100 868.37 838.04 898.71 3.5 1.3 2.7 105 761.49 733.91 789.08 3.6 1.4 2.6 110 669.89 644.79 694.99 3.7 1.5 2.5 TPS NTC PD S Please read Cautions and warnings and Important notes at the end of this document. 2019-09-23 Page 5 of 10 NTC thermistors for temperature measurement Probe assemblies R/T No. 7003 T (°C) B25/100 = 3625 K B58703M1103A00* M1703 Rnom (Ω) Rmin (Ω) Rmax (Ω) ∆R/Rnom (±%) ∆T (±K) α (%/K) 115 591.12 568.25 613.99 3.9 1.6 2.5 120 523.16 502.29 544.02 4.0 1.7 2.4 125 464.33 445.28 483.39 4.1 1.7 2.4 130 413.27 395.84 430.69 4.2 1.8 2.3 135 368.8 352.85 384.76 4.3 1.9 2.3 140 329.98 315.34 344.61 4.4 2.0 2.2 145 295.98 282.54 309.41 4.5 2.1 2.2 150 266.12 253.77 278.48 4.6 2.2 2.1 155 239.84 228.47 251.22 4.7 2.3 2.1 160 216.65 206.17 227.13 4.8 2.4 2.0 165 196.13 186.45 205.81 4.9 2.5 2.0 170 177.93 168.99 186.88 5.0 2.6 1.9 175 161.76 153.48 170.04 5.1 2.7 1.9 180 147.35 139.67 155.02 5.2 2.8 1.8 185 134.48 127.36 141.61 5.3 2.9 1.8 190 122.97 116.36 129.59 5.4 3.0 1.8 195 112.65 106.5 118.81 5.5 3.1 1.7 200 103.38 97.649 109.12 5.5 3.3 1.7 TPS NTC PD S Please read Cautions and warnings and Important notes at the end of this document. 2019-09-23 Page 6 of 10 NTC thermistors for temperature measurement Probe assemblies B58703M1103A00* M1703 Cautions and warnings Do not apply continuous pull-force between sensor and wire ends. Pull force requirement of 50 N is for short-term mounting conditions only. Consider metal compliance when mounting the sensor. Brass is not suitable for mounting sensor to an aluminum surface as contact corrosion may occur. Storage  Store thermistors only in original packaging. Do not open the package prior to storage.  Storage conditions in original packaging: storage temperature −10 °C ... +45 °C, relative humidity 45% up to 75% annual mean,