B81123C1472M000

Film Capacitors EMI Suppression Capacitors (MKP) Series/Type: Date: B81123 May 2009 © EPCOS AG 2009. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. EMI suppression capacitors (MKP) Y1 / 250 V AC B81123 Typical applications Y1 class for interference suppression "Line to ground" applications Climatic Max. operating temperature: 100 °C Climatic category (IEC 60068-1): 40/100/21 Construction Dielectric: polypropylene (MKP) Internal series connection Plastic case (UL 94 V-0) Epoxy resin sealing (UL 94 V-0) Features Self-healing properties Terminals Parallel wire leads, lead-free tinned Standard lead lengths: 6 1 mm Special lead lengths available on request Marking Manufacturer's logo, lot number, date code, rated capacitance (coded), cap. tolerance (code letter), rated AC voltage, series number, sub-class (Y1), dielectric code (MKP), climatic category, passive flammability category, approvals. Delivery mode Bulk (untaped) Taped (Ammo pack or reel) For taping details, refer to chapter "Taping and packing". Approvals Approval marks Dimensional drawing Dimensions in mm Lead spacing ±0.4 15, 22.5 Marking example Lead diameter d1 0.8 Standards EN 60384-14, IEC 60384-14 UL 1414 (double protection) Certificate 138584 E97863 Please read Cautions and warnings and Important notes at the end of this document. Page 2 of 16 B81123 Y1 / 250 V AC Overview of available types Lead spacing 15 mm CR (µF) 0.0010 0.0015 0.0022 0.0033 0.0047 0.0056 0.0068 0.010 Ordering codes and packing units Lead spacing mm 15 CR µF 0.0010 0.0015 0.0022 0.0033 0.0047 0.0056 0.0068 0.010 Max. dimensions w×h×l mm 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 7.0 × 16.0 × 26.5 8.5 × 16.5 × 26.5 10.5 × 18.5 × 26.5 Ordering code (composition see below) B81123C1102M*** B81123C1152M*** B81123C1222M*** B81123C1332M*** B81123C1472M*** B81123C1562M*** B81123C1682M*** B81123C1103M*** Ammo pack pcs./MOQ 4680 3840 3320 2720 2560 2320 1920 1560 Reel pcs./ MOQ 5200 4400 3600 2800 2800 2400 2000 1600 Untaped pcs./ MOQ 4000 4000 4000 2000 2000 2520 2040 2160 22.5 mm 22.5 MOQ = Minimum Order Quantity, consisting of 4 packing units. Composition of ordering code + = Capacitance tolerance code: M = ±20% *** = Packaging code: 289 = Ammo pack 189 = Reel 000 = Untaped (lead length 6 1 mm) Please read Cautions and warnings and Important notes at the end of this document. Page 3 of 16 B81123 Y1 / 250 V AC Technical data Max. operating temperature Top,max Dissipation factor tan δ (in 10-3) at 20 °C (upper limit values) Insulation resistance Rins or time constant τ = CR Rins at 20 °C, rel. humidity ≤ 65% (minimum as-delivered values) DC test voltage Passive flammability category to IEC 40 (CO) 752 Maximum continuous AC voltage VAC Rated AC voltage (IEC 60384-14) Maximum continuous DC voltage VDC Operating AC voltage Vop at high temperature Damp heat test Limit values after damp heat test +100 °C at 1 kHz 100 kHz 30 000 MΩ 1.0 5.0 4800 V, 2 s C 750 V (50/60 Hz) 250 V (50/60 Hz) 3000 V TA ≤ 100 °C Vop = VAC TA ≤ 100 °C Vop = 1.25 VAC (continuously) (1000 h) 21 days / 40 °C / 93% relative humidity Capacitance change ∆C/C ≤ 5% Dissipation factor change ∆ tan δ ≤ 0.5 10-3 (at 1 kHz) Insulation resistance Rins ≤ 1.0 10-3 (at 100 kHz) or time constant τ = CR Rins ≥ 50% of minimum as-delivered values Please read Cautions and warnings and Important notes at the end of this document. Page 4 of 16 B81123 Y1 / 250 V AC Pulse handling capability "dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal voltages, expressed in V/µs. "k0" represents the maximum permissible pulse characteristic of the waveform applied to the capacitor, expressed in V2/µs. Note: The values of dV/dt and k0 provided below must not be exceeded in order to avoid damaging the capacitor. dV/dt and k0 values Lead spacing dV/dt in V/µs k0 in V2/µs 15 mm 3 000 2 100 000 22.5 mm 1 000 700 000 Impedance Z versus frequency f (typical values) Please read Cautions and warnings and Important notes at the end of this document. Page 5 of 16 B81123 Y1 / 250 V AC Mounting guidelines 1 1.1 Soldering Solderability of leads The solderability of terminal leads is tested to IEC 60068-2-20, test Ta, method 1. Before a solderability test is carried out, terminals are subjected to accelerated ageing (to IEC 60068-2-2, test Ba: 4 h exposure to dry heat at 155 °C). Since the ageing temperature is far higher than the upper category temperature of the capacitors, the terminal wires should be cut off from the capacitor before the ageing procedure to prevent the solderability being impaired by the products of any capacitor decomposition that might occur. Solder bath temperature Soldering time Immersion depth Evaluation criteria: Visual inspection 1.2 235 ±5 °C 2.0 ±0.5 s 2.0 +0/ 0.5 mm from capacitor body or seating plane Wetting of wire surface by new solder ≥90%, free-flowing solder Resistance to soldering heat Resistance to soldering heat is tested to IEC 60068-2-20, test Tb, method 1A. Conditions: Series Solder bath temperature Soldering time 10 ±1 s MKT boxed (except 2.5 × 6.5 × 7.2 mm) 260 ±5 °C coated uncoated (lead spacing > 10 mm) MFP MKP (lead spacing > 7.5 mm) MKT boxed (case 2.5 × 6.5 × 7.2 mm) MKP (lead spacing ≤ 7.5 mm) MKT uncoated (lead spacing ≤ 10 mm) insulated (B32559) 5 ±1 s