EMI Suppression Capacitors (MKP)
Series/Type:
B81130*
The following products presented in this data sheet are being withdrawn.
Ordering Code
Substitute Product
B81130*
B3292*
Date of
Withdrawal
2007-08-10
Deadline Last
Orders
2008-09-30
Last Shipments
2008-12-31
For further information please contact your nearest EPCOS sales office, which will also support
you in selecting a suitable substitute. The addresses of our worldwide sales network are
presented at www.epcos.com/sales.
© EPCOS AG 2015. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
EPCOS AG is a TDK Group Company.
EMI suppression capacitors (MKP)
B81130
X2 / 275 VAC
Not for new design
Typical applications
X2 class for interference suppression
"Across the line" applications
Dimensional drawing
Climatic
Max. operating temperature: 100 °C
Climatic category (IEC 60068-1): 40/100/21
Construction
Dielectric: polypropylene (MKP)
Plastic case (UL 94 V-0)
Epoxy resin sealing (UL 94 V-0)
Dimensions in mm
Features
Small dimensions
Self-healing properties
Terminals
Parallel wire leads, lead-free tinned
Standard lead lengths: 6 1 mm
Special lead lengths available on request
Lead spacing
±0.4
Lead diameter d1
10 mm
15 ... 27.5 mm
0.6
0.8
Marking examples
= 10 mm
Marking
Manufacturer's logo, lot number,
date code, rated capacitance (coded),
cap. tolerance (code letter),
rated AC voltage,
series number, sub-class (X2),
dielectric code (MKP), climatic category,
passive flammability category, approvals.
≥15 mm/CR≤1 µF
= 27.5 mm/CR>1 µF
Delivery mode
Bulk (untaped)
Taped (Ammo pack or reel)
For taping details, refer to chapter
"Taping and packing".
Approvals
Marks of conformity
Standards
EN 132400, IEC 60384-14
Certificate
138554
UL 1414 / UL 1283
CSA C22.2 No.1
CQC (GB/T 14472-1998)
E97863 / E157153
E97863
CQC02001001667
2
B81130
X2 / 275 VAC
Not for new design
Overview of available types
Lead spacing 10 mm
15 mm
22.5 mm
CR (µF)
0.010
0.015
0.022
0.033
0.047
0.056
0.068
0.10
0.15
0.22
0.33
0.47
0.68
1.0
1.5
2.2
3
27.5 mm
B81130
X2 / 275 VAC
Not for new design
Ordering codes and packing units
Lead spacing CR
mm
10
15
22.5
27.5
µF
0.010
0.015
0.022
0.033
0.033
0.047
0.022
0.033
0.047
0.056
0.068
0.10
0.10
0.15
0.22
0.15
0.22
0.33
0.47
0.47
0.68
0.47
0.68
1.0
1.0
1.5
1.5
2.2
2.2
Max. dimensions
w×h×l
mm
4.0 × 9.0 × 13.0
4.0 × 9.0 × 13.0
5.0 × 11.0 × 13.0
5.0 × 11.0 × 13.0
6.0 × 12.0 × 13.0
6.0 × 12.0 × 13.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
6.0 × 11.0 × 18.0
6.0 × 12.0 × 18.0
7.0 × 12.5 × 18.0
8.5 × 14.5 × 18.0
9.0 × 17.5 × 18.0
6.0 × 15.0 × 26.5
7.0 × 16.0 × 26.5
8.5 × 16.5 × 26.5
10.5 × 16.5 × 26.5
10.5 × 18.5 × 26.5
11.0 × 20.5 × 26.5
11.0 × 21.0 × 31.5
11.0 × 21.0 × 31.5
12.5 × 21.5 × 31.5
13.5 × 23.0 × 31.5
15.0 × 24.5 × 31.5
18.0 × 27.5 × 31.5
18.0 × 27.5 × 31.5
19.0 × 30.0 × 31.5
Ordering code
(composition see
below)
B81130C1103+***
B81130C1153+***
B81130C1223+***
B81130C1333M***
B81130A1333+***
B81130C1473+***
B81130B1223+***
B81130B1333+***
B81130B1473+***
B81130C1563M***
B81130C1683+***
B81130C1104M***
B81130A1104+***
B81130C1154+***
B81130C1224+***
B81130B1154+***
B81130B1224+***
B81130C1334+***
B81130C1474M***
B81130A1474+***
B81130C1684+***
B81130B1474+***
B81130B1684+***
B81130C1105M***
B81130A1105+***
B81130C1155M***
B81130A1155+***
B81130C1225M***
B81130A1225+***
Ammo Reel
Untaped
pack
pcs./unit pcs./unit pcs./unit
1000
1000
830
830
680
680
1170
1170
1170
1170
960
960
830
680
640
680
580
480
390
390
370
1700
1700
1300
1300
1100
1100
1300
1300
1300
1300
1100
1100
900
700
700
700
600
500
400
400
350
350
350
300
250
Further E series and intermediate capacitance values on request.
Composition of ordering code
+ = Capacitance tolerance code:
M = ±20%
K = ±10%
*** = Packaging code:
289 = Ammo pack
189 = Reel
000 = Untaped (lead length 6 1 mm)
(Closer tolerances on request)
4
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
1000
500
500
720
630
510
540
540
510
320
320
280
260
240
200
200
180
B81130
X2 / 275 VAC
Not for new design
Technical data
Max. operating temperature Top,max
Dissipation factor tan δ (in 10-3)
at 20 °C (upper limit values)
+100 °C
at
1 kHz
100 kHz
CR ≤ 0.1 µF
CR > 0.1 µF
1.0
5.0
CR > 0.33 µF
30 000 s
1.0
Insulation resistance Rins
or time constant τ = CR Rins
at 20 °C, rel. humidity ≤ 65%
(minimum as-delivered values)
DC test voltage
CR ≤ 0.33 µF
100 000 MΩ
Passive flammability category
to IEC 40 (CO) 752
B
Maximum continuous AC voltage (V AC)
Rated AC voltage (IEC 60384-14)
Maximum continuous DC voltage (V DC)
Operating AC voltage V op at high
temperature
310 V (50/60 Hz)
275 V (50/60 Hz)
760 V
TA ≤ 100 °C Vop = VAC
TA ≤ 100 °C Vop = 1.25 VAC
Damp heat test
Limit values after damp heat test
21 days / 40 °C / 93% relative humidity
Capacitance change ∆C/C
≤ 5%
Dissipation factor change ∆ tan δ ≤ 0.5 10-3 (at 1 kHz)
Insulation resistance Rins
≤ 1.0 10-3 (at 10 kHz)
or time constant τ = CR Rins
≥ 50% of minimum
as-delivered values
2121 V, 2 s
5
(continuously)
(1000 h)
B81130
X2 / 275 VAC
Not for new design
Pulse handling capability
"dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal
voltages, expressed in V/µs.
"k0" represents the maximum permissible pulse characteristic of the waveform applied to the
capacitor, expressed in V 2/µs.
Note:
The values of dV/dt and k0 provided below must not be exceeded in order to avoid damaging the
capacitor.
dV/dt and k0 values
Lead spacing
dV/dt in V/µs
k0 in V2/µs
10 mm
15 mm
550
429 000
400
312 000
Impedance Z versus frequency f
(typical values)
6
22.5 mm
200
156 000
27.5 mm
150
117 000
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for certain
areas of application. These statements are based on our knowledge of typical requirements that are
often placed on our products in the areas of application concerned. We nevertheless expressly point
out that such statements cannot be regarded as binding statements about the suitability of our
products for a particular customer application. As a rule we are either unfamiliar with individual
customer applications or less familiar with them than the customers themselves. For these reasons, it is
always ultimately incumbent on the customer to check and decide whether a product with the properties
described in the product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or failure
before the end of their usual service life cannot be completely ruled out in the current state of the
art, even if they are operated as specified. In customer applications requiring a very high level of
operational safety and especially in customer applications in which the malfunction or failure of an
electronic component could endanger human life or health (e.g. in accident prevention or life-saving
systems), it must therefore be ensured by means of suitable design of the customer application or other
action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or
damage is sustained by third parties in the event of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this publication
may contain substances subject to restrictions in certain jurisdictions (e.g. because they are
classed as hazardous). Useful information on this will be found in our Material Data Sheets on the
Internet (www.tdk-electronics.tdk.com/material). Should you have any more detailed questions, please
contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications contained
in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products. Consequently, we
cannot guarantee that all products named in this publication will always be available. The
aforementioned does not apply in the case of individual agreements deviating from the foregoing for
customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to our General Terms and
Conditions of Supply.
7. Our manufacturing sites serving the automotive business apply the IATF 16949 standard. The
IATF certifications confirm our compliance with requirements regarding the quality management system
in the automotive industry. Referring to customer requirements and customer specific requirements
(“CSR”) TDK always has and will continue to have the policy of respecting individual agreements. Even
if IATF 16949 may appear to support the acceptance of unilateral requirements, we hereby like to
emphasize that only requirements mutually agreed upon can and will be implemented in our
Quality Management System. For clarification purposes we like to point out that obligations from IATF
16949 shall only become legally binding if individually agreed upon.
8. The trade names EPCOS, CeraCharge, CeraDiode, CeraLink, CeraPad, CeraPlas, CSMP, CTVS,
DeltaCap, DigiSiMic, ExoCore, FilterCap, FormFit, LeaXield, MiniBlue, MiniCell, MKD, MKK, MotorCap,
PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, PowerHap, PQSine, PQvar, SIFERRIT, SIFI,
SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, ThermoFuse, WindCap are
trademarks registered or pending in Europe and in other countries. Further information will be found
on the Internet at www.tdk-electronics.tdk.com/trademarks.
Release 2018-10
