B81192C3684K

Film Capacitors EMI Suppression Capacitors (MKP) Series/Type: Date: B81192 May 2009 © EPCOS AG 2009. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. EMI suppression capacitors (MKP) X3 / 250 V AC B81192 Typical applications X3 class for interference suppression "Across the line" applications Climatic Max. operating temperature: 85 °C Climatic category (IEC 60068-1): 40/085/56 Construction Dielectric: polypropylene (MKP) Epoxy resin coating (UL 94 V-0) Features High load currents Self-healing properties Sine-wave voltage High rate of voltage rise Vpp/τ Terminals Crimped wire leads, lead-free tinned (lead length 6 1 mm) Parallel wire leads, lead-free tinned (lead length 17 ±3 mm) Special lead lengths available on request Marking Minimum marking: Manufacturer's logo, rated cap. (coded), capacitance tolerance (code letter), date code, rated AC voltage (see also chapter "Marking and ordering code system") Delivery mode Bulk (untaped) Note Sub-class X3 corresponds to sub-class X2 as described in IEC 60384-14 (1st edition). Dimensions in mm Lead spacing ±0.5 10 ... 27.5 Lead diameter d1 0.8 Please read Cautions and warnings and Important notes at the end of this document. Page 2 of 16 B81192 X3 / 250 V AC Overview of available types Lead spacing 10 mm CR (µF) 0.010 0.015 0.022 0.033 0.039 0.047 0.056 0.068 0.082 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 1.0 15 mm 22.5 mm 27.5 mm Please read Cautions and warnings and Important notes at the end of this document. Page 3 of 16 B81192 X3 / 250 V AC Ordering codes and packing units Lead spacing CR mm 10 µF 0.010 0.015 0.022 0.033 0.039 0.047 0.056 0.068 0.082 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 1.0 Max. dimensions w×h×l mm 7.0 × 15.0 × 13.0 7.5 × 15.0 × 13.0 7.5 × 15.0 × 13.0 7.5 × 13.5 × 18.0 7.5 × 14.5 × 18.0 7.5 × 14.5 × 18.0 8.0 × 15.5 × 18.0 8.5 × 16.0 × 18.0 9.5 × 16.5 × 18.0 10.0 × 17.5 × 18.0 9.0 × 17.5 × 26.0 9.0 × 17.5 × 26.0 10.0 × 19.5 × 26.0 10.5 × 19.5 × 26.0 11.5 × 20.5 × 26.0 13.0 × 21.5 × 26.0 14.0 × 22.5 × 26.0 13.5 × 24.5 × 31.0 15.0 × 25.5 × 31.0 16.5 × 26.5 × 31.0 18.5 × 29.0 × 31.0 Ordering code (composition see below) B81192C3103+*** B81192C3153+*** B81192C3223+*** B81192C3333+*** B81192C3393+*** B81192C3473+*** B81192C3563+*** B81192C3683+*** B81192C3823+*** B81192C3104+*** B81192C3124+*** B81192C3154+*** B81192C3184+*** B81192C3224+*** B81192C3274+*** B81192C3334+*** B81192C3394+*** B81192C3474+*** B81192C3564+*** B81192C3684+*** B81192C3105+*** Untaped crimped pcs./MOQ 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 1000 1000 1000 1000 1000 1000 600 Untaped straight pcs./MOQ 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 1000 1000 1000 1000 1000 1000 600 15 22.5 27.5 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series and intermediate capacitance values on request. Composition of ordering code + = Capacitance tolerance code: M = ±20% K = ±10% *** = Packaging code: 010 = Untaped (crimped, lead length 6 1 mm) 008 = Untaped (straight, lead length 17 ±3 mm) Please read Cautions and warnings and Important notes at the end of this document. Page 4 of 16 B81192 X3 / 250 V AC Technical data Max. operating temperature Top,max Dissipation factor tan δ (in 10-3) at 20 °C (upper limit values) Insulation resistance Rins or time constant τ = CR Rins at 20 °C, rel. humidity ≤ 65% (minimum as-delivered values) DC test voltage Passive flammability category to IEC 40 (CO) 752 Maximum continuous AC voltage (VAC) Rated AC voltage (IEC 60384-14) Maximum continuous DC voltage (VDC) Operating AC voltage Vop at high temperature Damp heat test Limit values after damp heat test +85 °C at 1 kHz 100 kHz CR ≤ 0.33 µF 15 GΩ CR ≤ 0.33 µF 1.0 5.0 CR > 0.33 µF 5 GΩ CR > 0.33 µF 1.0 10 1850 V, 2 s B 250 V (50/60 Hz) 250 V (50/60 Hz) 560 V TA ≤ Vop = VAC TA ≤ Vop = 1.25 VAC (continuously) (1000 h) 56 days / 40 °C / 93% relative humidity Capacitance change ∆C/C ≤ 3% Dissipation factor change ∆ tan δ ≤ 0.5 10-3 (at 1 kHz) Insulation resistance Rins ≤ 1.0 10-3 (at 10 kHz) or time constant τ = CR Rins ≥ 50% of minimum as-delivered values Pulse handling capability "dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal voltages, expressed in V/µs. "k0" represents the maximum permissible pulse characteristic of the waveform applied to the capacitor, expressed in V2/µs. Note: The values of dV/dt and k0 provided below must not be exceeded in order to avoid damaging the capacitor. dV/dt and k0 values Lead spacing dV/dt in V/µs k0 in V2/µs 10 mm 60 42 000 15 mm 50 35 000 22.5 mm 30 21 000 27.5 mm 20 14 000 Please read Cautions and warnings and Important notes at the end of this document. Page 5 of 16 B81192 X3 / 250 V AC Mounting guidelines 1 1.1 Soldering Solderability of leads The solderability of terminal leads is tested to IEC 60068-2-20, test Ta, method 1. Before a solderability test is carried out, terminals are subjected to accelerated ageing (to IEC 60068-2-2, test Ba: 4 h exposure to dry heat at 155 °C). Since the ageing temperature is far higher than the upper category temperature of the capacitors, the terminal wires should be cut off from the capacitor before the ageing procedure to prevent the solderability being impaired by the products of any capacitor decomposition that might occur. Solder bath temperature Soldering time Immersion depth Evaluation criteria: Visual inspection 1.2 235 ±5 °C 2.0 ±0.5 s 2.0 +0/ 0.5 mm from capacitor body or seating plane Wetting of wire surface by new solder ≥90%, free-flowing solder Resistance to soldering heat Resistance to soldering heat is tested to IEC 60068-2-20, test Tb, method 1A. Conditions: Series Solder bath temperature Soldering time 10 ±1 s MKT boxed (except 2.5 × 6.5 × 7.2 mm) 260 ±5 °C coated uncoated (lead spacing > 10 mm) MFP MKP (lead spacing > 7.5 mm) MKT boxed (case 2.5 × 6.5 × 7.2 mm) MKP (lead spacing ≤ 7.5 mm) MKT uncoated (lead spacing ≤ 10 mm) insulated (B32559) 5 ±1 s