B82412A1182M000

SMT inductors SIMID series, SIMID 1210-01 Series/Type: Date: B82412A March 2008 Data Data Sheet  EPCOS AG 2008. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS’ prior express consent is prohibited. SMT inductors, SIMID series SIMID 1210-01 Size 1210 (EIA) or 3225 (IEC) Rated inductance 0.010 µH to 10 µH Rated current 90 mA to 700 mA Construction ■ Ceramic or ferrite core ■ Single-layer winding fixed by glue ■ Ultrasonic-welded winding B82412A Features ■ ■ ■ ■ Low height High Q factor High resonance frequency Suitable for lead-free reflow soldering as referenced in JEDEC J-STD 020C ■ RoHS-compatible Applications ■ ■ ■ ■ ■ Filtering of supply voltages, coupling, decoupling Antenna systems Infotainment Telecommunications Industrial electronics Terminals ■ Base material CuSn6 ■ Layer composition Cu, Ag (lead-free) ■ Electro-plated Marking ■ No marking on component ■ Minimum data on reel: Manufacturer, ordering code, L value, quantity, date of packing Delivery mode and packing units ■ 8-mm blister tape, wound on 180-mm or 330-mm ∅ reel ■ Packing units: 180-mm reel: 2500 pcs./reel 330-mm reel: 10000 pcs./reel Please read Cautions and warnings and Important notes at the end of this document. 2 03/08 SMT inductors, SIMID series SIMID 1210-01 Dimensional drawing and layout recommendation 0.25 min.1) 1.8 _ 0.3 1) A B82412A 0.8 B C D B IND0053-6 1.6 _ 0.3 0.1±0.05 0.6±0.1 A 0.2 min. 1) B 1.15 C 2.1 D 4.4 2.7 2.5±0.2 2.8 3.2+0.3 1) Soldering area IND0052-V-E Dimensions in mm Taping and packing Blister tape 1.75±0.1 4±0.1 Component 1.5+0.1 2±0.05 Reel 14.4 max. _0 12.75 +0.15 3.5±0.05 _2 180 +0 _ < 4.2 8±0.3 _ < 2.0 4±0.1 1.0+0.2 Direction of unreeling IND0570-T-E _0 8.4 +1.5 _2 330 +0 62±1.5 IND0592-V Dimensions in mm Please read Cautions and warnings and Important notes at the end of this document. 3 03/08 SMT inductors, SIMID series SIMID 1210-01 Technical data and measuring conditions Rated inductance LR Q factor Qmin Rated temperature TR Rated current IR B82412A Measured with impedance analyzer Agilent 4294A at frequency fL, 0.1 V, 20 °C Measured with impedance analyzer Agilent 4294A at frequency fQ, 20 °C 85 °C Maximum permissible DC with inductance decrease ∆L/L0 ≤ 10% and temperature increase of ≤ 20 K at rated temperature Measured with network analyzer Agilent 8753D, 20 °C Measured at 20 °C Sn95.5Ag3.8Cu0.7: (245 ±5) °C, (5 ±0.3) s Wetting of soldering area ≥ 95% (based on IEC 60068-2-58) 260 °C, 40 s (as referenced in JEDEC J-STD 020C) 55/125/56 (to IEC 60068-1) Mounted: –55 °C … +125 °C Packaged: –25 °C … +40 °C, ≤ 75% RH Approx. 40 mg Self-resonance frequency fres,min DC resistance Rmax Solderability (lead-free) Resistance to soldering heat Climatic category Storage conditions Weight Please read Cautions and warnings and Important notes at the end of this document. 4 03/08 SMT inductors, SIMID series SIMID 1210-01 Characteristics and ordering codes LR µH Core material: ceramic 0.010 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 ±5% ^ B82412A Tolerance fL MHz Qmin fQ MHz IR mA 700 700 640 640 600 600 540 500 470 460 440 430 400 380 370 340 320 300 280 260 225 200 180 150 Rmax Ω 0.10 0.10 0.12 0.12 0.12 0.15 0.17 0.18 0.22 0.23 0.25 0.27 0.30 0.35 0.36 0.42 0.48 0.55 0.65 0.75 1.00 1.20 1.40 2.00 fres,min MHz 4000 3500 3000 2700 2400 2200 2000 1700 1600 1400 1350 1100 1000 900 820 700 630 570 550 500 450 430 400 380 Ordering code 1) (∅ 180-mm reel) ±20% ^ M 10 10 10 10 25 25 25 30 30 20 25 25 25 30 30 30 30 25 25 25 25 30 30 30 30 30 30 30 100 100 100 100 100 50 50 50 50 50 50 50 50 30 30 30 30 30 30 30 30 30 30 30 B82412A3100M000 B82412A3120M000 B82412A3150M000 B82412A3180M000 B82412A3220+000 B82412A3270+000 B82412A3330+000 B82412A3390+000 B82412A3470+000 B82412A3560+000 B82412A3680+000 B82412A3820+000 B82412A3101+000 B82412A3121+000 B82412A3151+000 B82412A3181+000 B82412A3221+000 B82412A3271+000 B82412A3331+000 B82412A3391+000 B82412A3471+000 B82412A3561+000 B82412A3681+000 B82412A3821+000 J ^ 10 K 10 10 10 10 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 ±10% Closer tolerances and special versions on request. 1) Replace the + by the code letter for the required inductance tolerance. For reel size ∅ 330 mm the last digit has to be an »8«. Example: B82412A3100M008 Please read Cautions and warnings and Important notes at the end of this document. 5 03/08 SMT inductors, SIMID series SIMID 1210-01 Characteristics and ordering codes LR µH Core material: ferrite 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 ±5% ^ B82412A Tolerance fL MHz Qmin fQ MHz IR mA 330 310 300 290 270 220 200 190 160 140 120 110 90 Rmax Ω 0.45 0.50 0.55 0.60 0.65 1.05 1.10 1.35 1.80 2.70 3.50 3.80 5.50 fres,min MHz 300 260 240 220 200 180 160 150 140 125 115 100 95 Ordering code 1) (∅ 180-mm reel) J ^ 1 K 1 1 1 1 1 1 1 1 1 1 1 1 30 30 30 30 30 30 30 30 35 35 35 35 35 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 B82412A1102+000 B82412A1122+000 B82412A1152+000 B82412A1182+000 B82412A1222+000 B82412A1272+000 B82412A1332+000 B82412A1392+000 B82412A1472+000 B82412A1562+000 B82412A1682+000 B82412A1822+000 B82412A1103+000 ±10% Closer tolerances and special versions on request. 1) Replace the + by the code letter for the required inductance tolerance. For reel size ∅ 330 mm the last digit has to be an »8«. Example: B82412A1102M008 Please read Cautions and warnings and Important notes at the end of this document. 6 03/08 SMT inductors, SIMID series SIMID 1210-01 Impedance |Z| versus frequency f measured with impedance analyzer Agilent 4291A, typical values at 20 °C 10 5 IND0054-8 B82412A Inductance L versus DC load current IDC measured with LCR meter Agilent 4275A, typical values at 20 °C 10 2 µH L 10 1 10.0 µH 6.8 µH 1 µH 0.68 µH B82412A IND0055-W Ω B82412A 10 µH 1 µH 100 nH 10 nH |Z | 10 4 10 3 10 2 10 0 10 1 10 _1 0.1 µH 10 0 0.022 µH _1 _2 10 10 6 10 7 10 8 Hz 10 f 9 10 10 _2 10 _1 10 0 A 10 1 I DC Q factor versus frequency f measured with impedance analyzer Agilent 4194A/4291A, typical values at 20 °C 100 B82412A Q 90 80 70 60 50 40 30 20 10 05 10 10 6 10 7 10 8 Hz 10 9 f 10 µH 1 µH 0.1 µH 0.022 µH IND0056-9 Current derating Iop/IR versus ambient temperature TA (rated temperature TR = 85 °C) 1.2 Iop IR B82412A 1.0 IND0057-H-E 0.8 0.6 0.4 0.2 0 0 20 40 60 80 100 ˚C TA 140 7 03/08 Cautions and warnings ■ Please note the recommendations in our Inductors data book (latest edition) and in the data sheets. – Particular attention should be paid to the derating curves given there. – The soldering conditions should also be observed. Temperatures quoted in relation to wave soldering refer to the pin, not the housing. ■ If the components are to be washed varnished it is necessary to check whether the washing varnish agent that is used has a negative effect on the wire insulation, any plastics that are used, or on glued joints. In particular, it is possible for washing varnish agent residues to have a negative effect in the long-term on wire insulation. ■ The following points must be observed if the components are potted in customer applications: – Many potting materials shrink as they harden. They therefore exert a pressure on the plastic housing or core. This pressure can have a deleterious effect on electrical properties, and in extreme cases can damage the core or plastic housing mechanically. – It is necessary to check whether the potting material used attacks or destroys the wire insulation, plastics or glue. – The effect of the potting material can change the high-frequency behaviour of the components. ■ Ferrites are sensitive to direct impact. This can cause the core material to flake, or lead to breakage of the core. ■ Even for customer-specific products, conclusive validation of the component in the circuit can only be carried out by the customer. Please read Cautions and warnings and Important notes at the end of this document. 8 03/08 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DSSP, MiniBlue, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. 9 03/09