B82720S2152N040

Power line chokes Current-compensated ring core double chokes 250 V AC, 0.3 … 2 A, 1.1 … 22 mH Series/Type: Date: B82720S January 2010 a~í~=pÜÉÉí a~í~=pÜÉÉí ¤ EPCOS AG 2010. Reproduction, publication and dissemination of this publication and the information contained therein without EPCOS’ prior express consent is prohibited. Power line chokes Current-compensated ring core double chokes Rated voltage 250 V AC Rated current 0.3 A to 2 A Rated inductance 1.1 mH to 22 mH Construction ■ ■ ■ ■ ■ B82720S Current-compensated ring core double choke Ferrite core LCP case (UL 94 V-0) Silicone potting Sector winding Features ■ Approx. 0.8% stray inductance for differential-mode interference suppression ■ Suitable for reflow soldering ■ Design complies with EN 60938-2 (VDE 0565-2) ■ RoHS-compatible Applications ■ Suppression of common-mode interferences ■ Compact electronic ballasts in lamps ■ Compact switch-mode power supplies Terminals ■ Base material CuSn6 ■ Layer composition Ni, Sn ■ Hot-dipped Marking ■ Marking on component: Manufacturer, ordering code, rated inductance, rated current, graphic symbol, rated voltage, date of manufacture (YYWWD) ■ Minimum data on reel: Manufacturer, ordering code, rated inductance, rated current, quantity, date of packing Delivery mode and packing unit ■ 24-mm blister tape, wound on 330-mm ‡ reel ■ Packing unit: 250 pcs./reel Please read Cautions and warnings and Important notes at the end of this document. 2 01/10 Power line chokes Current-compensated ring core double chokes Dimensional drawing and pin configuration 2.2±0.2 1) 2.5±0.1 _ 0.05 0.6 +0.1 1) B82720S Layout recommendation 2.5 4 5 5 1.6 2.5±0.1 5±0.1 1 14.9±0.3 14.5 max. _ 0.05 0.4 +0.1 1) 8 12 17.6 IND0244-2 0˚... 6˚ 10.5±0.2 8±0.2 16.6±0.4 1 2 3 4 8 7 Marking 6 5 13.3 max. 0.1 1) Soldering area IND0243-T-E Dimensions in mm Taping and packing Blister tape Reel Dimensions in mm Please read Cautions and warnings and Important notes at the end of this document. 3 01/10 2.5 Power line chokes Current-compensated ring core double chokes Technical data and measuring conditions Rated voltage VR Test voltage Vtest Rated temperature TR Rated current IR Rated inductance LR Inductance tolerance Inductance decrease 'L/L0 Stray inductance Lstray,typ DC resistance Rtyp Solderability (lead free) 250 V AC (50/60 Hz) 1500 V AC, 2 s (line/line) 40 °C Referred to 50 Hz and rated temperature B82720S Measured with Agilent 4284A at 10 kHz, 0.1 mA, 20 °C Inductance is specified per winding. –30/+50% at 20 °C < 10% at DC magnetic bias with IR, 20 °C Measured with Agilent 4284A at 10 kHz, 5 mA, 20 °C, typical values Measured at 20 °C, typical values, specified per winding Sn96.5Ag3.0Cu0.5: (245 r5) °C, (3 r0.3) s Wetting of soldering area t 95% (to IEC 60068-2-58, test Td) (260 r5) °C, (10 r1) s (to IEC 60068-2-58, test Td) 40/125/56 (to IEC 60068-1) –25 °C … +40 °C, d 75% RH Approx. 2.5 g Resistance to soldering heat Climatic category Storage conditions (packaged) Weight Characteristics and ordering codes IR A 0.3 0.3 0.6 1.0 1.5 2.0 LR mH 22 12 4.4 3.0 1.6 1.1 Lstray,typ PH 130 80 30 20 10 6 Rtyp m: 1500 1100 400 220 110 65 B82720S2301N042 B82720S2301N040 B82720S2601N040 B82720S2102N040 B82720S2152N040 B82720S2202N040 Ordering code Please read Cautions and warnings and Important notes at the end of this document. 4 01/10 Power line chokes Current-compensated ring core double chokes Impedance |Z| versus frequency f measured with windings in parallel at 20 °C, typical values 10 6 IND0611-S B82720S Current derating Iop/IR versus temperature TA 1.4 I op I R 1.2 1.0 TR = 40 ˚C 0.8 IND0373-A-E Ω | Z| 10 5 B82720 10 4 0.6 S2301N042 S2301N040 S2601N040 S2102N040 S2152N040 S2202N040 10 5 10 6 Hz 10 7 f 10 3 0.4 0.2 0 10 2 4 10 0 20 40 60 80 100 ˚C 140 TA 5 01/10 Power line chokes Current-compensated ring core double chokes Recommended reflow soldering profile Pb-free solder material (based on JEDEC J-STD 020C) t3 T4 T3 T2 t2 B82720S T1 t1 IND0814-F T1 °C 150 T2 °C 200 T3 °C 217 T4 °C 245 t1 s < 110 t2 s < 90 t3 s < 30 @ T4 –5 °C Time from 25 °C to T4: max 300 s Max. numbers of reflow cycles: 3 Please read Cautions and warnings and Important notes at the end of this document. 6 01/10 Cautions and warnings ■ Please note the recommendations in our Inductors data book (latest edition) and in the data sheets. – Particular attention should be paid to the derating curves given there. – The soldering conditions should also be observed. Temperatures quoted in relation to wave soldering refer to the pin, not the housing. ■ If the components are to be washed varnished it is necessary to check whether the washing varnish agent that is used has a negative effect on the wire insulation, any plastics that are used, or on glued joints. In particular, it is possible for washing varnish agent residues to have a negative effect in the long-term on wire insulation. ■ The following points must be observed if the components are potted in customer applications: – Many potting materials shrink as they harden. They therefore exert a pressure on the plastic housing or core. This pressure can have a deleterious effect on electrical properties, and in extreme cases can damage the core or plastic housing mechanically. – It is necessary to check whether the potting material used attacks or destroys the wire insulation, plastics or glue. – The effect of the potting material can change the high-frequency behaviour of the components. ■ Ferrites are sensitive to direct impact. This can cause the core material to flake, or lead to breakage of the core. ■ Even for customer-specific products, conclusive validation of the component in the circuit can only be carried out by the customer. Please read Cautions and warnings and Important notes at the end of this document. 7 01/10 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DeltaCap, DigiSiMic, DSSP, MiniBlue, MiniCell, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. 8 01/10