B84773A0004A000

EMC filters Series/Type: B84773*A000 Date: December 2012 © EPCOS AG 2015. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. EPCOS AG is a TDK Group Company. 2-line filters B84773*A000 IEC inlet filters Power line filters for 1-phase systems Rated voltage VR: 250 V AC/DC Rated current IR: 1 A to 10 A Construction 2-line filter with IEC connector and fuse holder Appliance connector according to IEC/EN 60320-1 Fuse holder for 2 fuses ∅ 5 × 20 mm Metal case Versions Standard version (B84773A*) Medical version with low leakage current (B84773M*) Features Easy to install Compact design Cost optimized construction Degree of protection from front side IP 401) UL and cUL approval obtained ENEC 10 approval is pending Applications Switched-mode power supplies for  industrial electronics  telecom systems  data systems DC applications Measuring instruments Medical engineering Terminals Line side: IEC inlet C14 according to IEC/EN 60320-1 Load side: Tab connectors 6.3 × 0.8 mm Marking Marking on component: Manufacturer's logo, ordering code, rated voltage, rated current, rated temperature, climatic category, date code Minimum data on packaging: Manufacturer's logo, ordering code, quantity, date code 1) To IEC 60529 Please read Cautions and warnings and Important notes at the end of this document. Page 2 of 14 2-line filters B84773*A000 IEC inlet filters Typical circuit diagram of B84773A*A000 (standard version) Typical circuit diagram of B84773M*A000 (medical version) Please read Cautions and warnings and Important notes at the end of this document. Page 3 of 14 2-line filters B84773*A000 IEC inlet filters Technical data and measuring conditions of B84773*A000 Rated voltage VR Rated current IR Test voltage Vtest Climatic category (IEC 60068-1) 250 V AC (50/60 Hz) / 250 V DC Referred to 40 °C rated temperature B84773A*: 760 V AC, 2 s (line/line) B84773M*: 1700 V DC, 2 s (line/line) B84773A*: 2000 V AC, 2 s (lines/case) B84773M*: 2500 V AC, 2 s (lines/case) 25/085/21 (25 °C/+85 °C/21 days damp heat test) Characteristics and ordering codes of B84773*A000 VR = 250 V AC/DC IR A 1 2 4 6 10 CR X2 µF CR Y2 pF 1 × 0.1 1 × 0.1 1 × 0.1 1 × 0.1 1 × 0.1 1 × 0.1 1 × 0.1 1 × 0.1 1 × 0.1 1 × 0.1 2 × 2200  2 × 2200  2 × 2200  2 × 2200  2 × 2200  LR Ileak1) mH 2 × 5.4 2 × 5.4 2 × 2.7 2 × 2.7 2 × 1.1 2 × 1.1 2 × 0.3 2 × 0.3 2 × 0.2 2 × 0.2 mA 0.173 0 0.173 0 0.173 0 0.173 0 0.173 0 Rbleed Approx. weight MΩ g 1 55 1 55 1 55 1 55 1 55 1 55 1 55 1 55 1 75 1 75 Ordering code Approvals B84773A0001A000 B84773M0001A000 B84773A0002A000 B84773M0002A000 B84773A0004A000 B84773M0004A000 B84773A0006A000 B84773M0006A000 B84773A0010A000 B84773M0010A000 P P P P P P P P P P × × × × × × × × × × × × × × × × × × × × × = Approval granted P = Approval pending 1) Calculation according draft proposal IEC 609391 Ed. 3 (20081029), annex A, ”Calculation of leakage current” at 50 Hz. In practice are up to double values to be expected due to the insulation resistance values of the used ceramic capacitors. For the medical version results computationally the value 0. In practice are values 1 ... 2 µA to be expected due to the insulation resistance values of the used materials. Please read Cautions and warnings and Important notes at the end of this document. Page 4 of 14 2-line filters B84773*A000 IEC inlet filters Dimensional drawing General tolerances according to ISO 2768cL Dimensions in mm Please read Cautions and warnings and Important notes at the end of this document. Page 5 of 14 2-line filters B84773*A000 IEC inlet filters Insertion loss (typical values at Z = 50 Ω) Filter for 1 A Filter for 2 A Filter for 4 A Filter for 6 A Please read Cautions and warnings and Important notes at the end of this document. Page 6 of 14 2-line filters B84773*A000 IEC inlet filters Insertion loss (typical values at Z = 50 Ω) Filter for 10 A Please read Cautions and warnings and Important notes at the end of this document. Page 7 of 14 2-line filters B84773*A000 IEC inlet filters Insertion loss (typical values at Z = 50 Ω) Filter for 1 A Filter for 2 A Filter for 4 A Filter for 6 A Please read Cautions and warnings and Important notes at the end of this document. Page 8 of 14 2-line filters B84773*A000 IEC inlet filters Insertion loss (typical values at Z = 50 Ω) Filter for 10 A Please read Cautions and warnings and Important notes at the end of this document. Page 9 of 14 2-line filters B84773*A000 IEC inlet filters Cautions and warnings Please read all safety and warning notes carefully before installing the EMC filter and putting it into operation (see ). The same applies to the warning signs on the filter. Please ensure that the signs are not removed nor their legibility impaired by external influences. Death, serious bodily injury and substantial material damage to equipment may occur if the appropriate safety measures are not carried out or the warnings in the text are not observed. Using according to the terms The EMC filters may be used only for their intended application within the specified values in lowvoltage networks in compliance with the instructions given in the data sheets and the data book. The conditions at the place of application must comply with all specifications for the filter used. Warning It shall be ensured that only qualified persons (electricity specialists) are engaged on work such as planning, assembly, installation, operation, repair and maintenance. They must be provided with the corresponding documentation. Danger of electric shock. EMC filters contain components that store an electric charge. Dangerous voltages can continue to exist at the filter terminals for longer than five minutes even after the power has been switched off. The protective earth connections shall be the first to be made when the EMC filter is installed and the last to be disconnected. Depending on the magnitude of the leakage currents, the particular specifications for making the protective-earth connection must be observed. Impermissible overloading of the EMC filter, such as with circuits able to cause resonances, impermissible voltages at higher frequencies etc. can lead to bodily injury and death as well as cause substantial material damages (e.g. destruction of the filter housing). EMC filters must be protected in the application against impermissible exceeding of the rated currents by overcurrent protective circuitry. In case of leakage currents >3.5 mA you shall mount the PE conductor stationary with the required cross section before beginning of operation and save it against disconnecting. For leakage currents IL1) 250 A For operating currents greater than 250 A, we Mounting recommend the PE connection to be set up between instructions, point the feed (filter: line) and output (filter: load) not via the 2 PE terminal bolt in the filter housing. Please read Cautions and warnings and Important notes at the end of this document. Page 11 of 14 2-line filters B84773*A000 IEC inlet filters Topic Mounting position Long motor cables Instructions Reference chapter (databook), paragraph Note the mounting position of the filters! It must Mounting always be ensured that natural convection is not instructions, point impaired. 13 Long motor cables cause parasitic currents in the Mounting installation. instructions, point 15 Please read Cautions and warnings and Important notes at the end of this document. Page 12 of 14 2-line filters B84773*A000 IEC inlet filters Symbols and terms Symbol α CR CX CY ∆V dv/dt f fM fP fR fres ILK IC Imax IN Iop Ipk Iq IR IS L LR Lstray Ploss R Ris Rtyp TA Tmax Tmin TR Veff VLE VN VR Vpeak Vtest VX VY Z |Z| English Insertion loss Rated capacitance Capacitance X capacitor Capacitance Y capacitor Voltage drop (input to output) Rate of voltage rise Frequency Converter output frequency Pulse frequency Rated frequency Resonant frequency Filter leakage current Current through capacitor Maximum current Nominal current Operating current (design current) Rated peak withstand current Capacitive reactive current Rated current Interference current Inductance Rated inductance Stray inductance Power loss Resistance Insulation resistance DC resistance, typical value Ambient temperature Upper category temperature Lower category temperature Rated temperature RMS voltage Voltage line to earth; voltage line to ground Nominal voltage Rated voltage Peak voltage Test voltage Voltage over X capacitor Voltage over Y capacitor Impedance Impedance, absolute value Please read Cautions and warnings and Important notes at the end of this document. Page 13 of 14 German Einfügungsdämpfung Bemessungskapazität Kapazität X-Kondensator Kapazität Y-Kondensator Spannungsabfall im Filter Spannungsanstiegsgeschwindigkeit Frequenz Motorfrequenz Pulsfrequenz Bemessungsfrequenz Resonanzfrequenz Filter-Ableitstrom Strom durch Kondensator Maximalstrom Nennstrom Betriebsstrom Bemessungs-Stoßstromfestigkeit Kapazitiver Blindstrom Bemessungsstrom Störstrom Induktivität Bemessungsinduktivität Streuinduktivität Verlustleistung Widerstand Isolationswiderstand Gleichstromwiderstand, Richtwert Umgebungstemperatur Obere Kategorietemperatur Untere Kategorietemperatur Bemessungstemperatur Effektivspannung Spannung Phase zu Erdpotential Netzspannung Bemessungsspannung Spitzenspannung Prüfspannung Spannung über X-Kondensator Spannung über Y-Kondensator Scheinwidertand Scheinwiderstand (Betragswert) Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule we are either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether a product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.tdk-electronics.tdk.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to our General Terms and Conditions of Supply. 7. Our manufacturing sites serving the automotive business apply the IATF 16949 standard. The IATF certifications confirm our compliance with requirements regarding the quality management system in the automotive industry. Referring to customer requirements and customer specific requirements (“CSR”) TDK always has and will continue to have the policy of respecting individual agreements. Even if IATF 16949 may appear to support the acceptance of unilateral requirements, we hereby like to emphasize that only requirements mutually agreed upon can and will be implemented in our Quality Management System. For clarification purposes we like to point out that obligations from IATF 16949 shall only become legally binding if individually agreed upon. 8. The trade names EPCOS, CeraCharge, CeraDiode, CeraLink, CeraPad, CeraPlas, CSMP, CTVS, DeltaCap, DigiSiMic, ExoCore, FilterCap, FormFit, LeaXield, MiniBlue, MiniCell, MKD, MKK, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, PowerHap, PQSine, PQvar, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.tdk-electronics.tdk.com/trademarks. Release 2018-10 Page 14 of 14