B85121A2504A201

EMC Feedthrough Capacitors, Feedthrough components Series/Type: B85121, B85121A The following products presented in this data sheet are being withdrawn. Ordering Code Substitute Product B85121A4503B250 B85121A4252C160 B85121A2504A630 B85121*, B85321* Date of Withdrawal 2015-03-13 2015-03-13 2019-06-21 Deadline Last Orders 2015-06-30 2015-06-30 2019-09-30 Last Shipments 2015-09-30 2015-09-30 2019-12-31 Ordering Code Substitute Product B85121A2504A201 B85121A2504A101 B85121A2503C160 B85121A2503B250 B85121A2475A630 B85121A2475A201 B85121A2475A101 B85121A2353A250 B85121A2205A630 B85121A2205A201 B85121A2205A101 B85121A2105A750 B85121A2105A630 B85121A2105A250 B85121A2105A201 B85121A2105A101 B85121A2104E750 B85121A2103C160 B85121A1104C160 B85121*, B85321* B85121*, B85321* B85121*, B85321* B85121*, B85321* B85121*, B85321* B85121*, B85321* B85121*, B85321* B85121*, B85321* Date of Withdrawal 2019-06-21 2019-06-21 2015-03-13 2015-03-13 2019-06-21 2019-06-21 2019-06-21 2015-03-13 2019-06-21 2019-06-21 2019-06-21 2015-03-13 2015-03-13 2015-03-13 2015-03-13 2015-03-13 2015-03-13 2015-03-13 2015-03-13 Deadline Last Orders 2019-09-30 2019-09-30 2015-06-30 2015-06-30 2019-09-30 2019-09-30 2019-09-30 2015-06-30 2019-09-30 2019-09-30 2019-09-30 2015-06-30 2015-06-30 2015-06-30 2015-06-30 2015-06-30 2015-06-30 2015-06-30 2015-06-30 Last Shipments 2019-12-31 2019-12-31 2015-09-30 2015-09-30 2019-12-31 2019-12-31 2019-12-31 2015-09-30 2019-12-31 2019-12-31 2019-12-31 2015-09-30 2015-09-30 2015-09-30 2015-09-30 2015-09-30 2015-09-30 2015-09-30 2015-09-30 Please contact your nearest TDK sales office if you need support in selecting a suitable substitute. The addresses of our worldwide sales network are presented at www.tdkelectronics.tdk.com/sales. Ordering Code B85121A2503B250 B85121A2353A250 B85121A2105A750 B85121A2105A630 B85121A2105A250 B85121A2105A201 B85121A2105A101 B85121A2104E750 B85121A2103C160 B85121A1104C160 Substitute Product Date of Withdrawal 2015-03-13 2015-03-13 2015-03-13 2015-03-13 2015-03-13 2015-03-13 2015-03-13 2015-03-13 2015-03-13 2015-03-13 Deadline Last Orders 2015-06-30 2015-06-30 2015-06-30 2015-06-30 2015-06-30 2015-06-30 2015-06-30 2015-06-30 2015-06-30 2015-06-30 Last Shipments 2015-09-30 2015-09-30 2015-09-30 2015-09-30 2015-09-30 2015-09-30 2015-09-30 2015-09-30 2015-09-30 2015-09-30 For further information please contact your nearest EPCOS sales office, which will also support you in selecting a suitable substitute. The addresses of our worldwide sales network are presented at www.epcos.com/sales. Feedthrough components B85121 Capacitors Rated voltage VR: 110 V AC to 440 V AC Rated current IR: 16 A to 200 A Rated capacitance CR: 0.0025 µF to 4.7 µF Construction Building-block system MKP/MKT technology (dry, self-healing) Dielectric: polypropylene or polyester, metallized Metal case, polyurethane potting (UL 94 V-0) For central screw fixing Features Compact dimensions High insertion loss Easy to install High contact reliability thanks to central screw fixing Design complies with IEC 60384-14 UL 60384-14 pending Typical applications Broadband interference suppression for AC/DC supply lines, e. g. in shielded rooms telephone exchanges, base stations electrical machines and systems power supplies Terminals Threaded studs Axial leads Marking Marking on component: Manufacturer's logo, ordering code, rated capacitance, rated voltage, rated current, climatic category, circuit diagram, date code Minimum data on packaging: Manufacturer's logo, ordering code, quantity, date code Circuit diagram Please read Cautions and warnings and Important notes at the end of this document. Page 2 of 13 Feedthrough components B85121A*160 ∅ 16 mm, 16 A Capacitors Feedthrough capacitors ∅ 16 mm Technical data and measuring conditions Rated voltage VR Rated current IR Capacitance tolerance Climatic category (IEC 60068-1) 110 V AC … 440 V AC (50/60 Hz) / 160 V DC … 600 V DC Referred to 40 °C rated temperature Reduced current values at 400 Hz ±20% 40/085/56 (40 °C/+85 °C/56 days damp heat test) Screw cap fixing M10 × 0.75 Approvals UL 60384-14, 250 V AC pending1) 1) UL1283 approval expired in Dec. 2013 Characteristics and ordering codes IR CR A µF VR = 110 V AC 16 0.1 VR = 250 V AC 16 0.01 16 0.05 VR = 440 V AC 16 0.0025 VR DC V Vtest DC V Terminal Approx. weight g Ordering code Approvals 160 800 Axial leads 45 B85121A1104C160 P 600 600 1750 1750 Axial leads Axial leads 45 45 B85121A2103C160 B85121A2503C160 P P 600 4350 Axial leads 45 B85121A4252C160 P P = Approval pending Insertion loss (dB); typical values at 50 Ω CR (µF) 10 kHz 100 kHz 1 MHz 10 MHz 100 MHz > 300 MHz 0.0025    12 45 > 60 4 25 55 > 70 1 17 35 52 > 80 4 20 40 60 > 80 0.01 0.05 0.1     Dimensional drawing B85121A*C160 Tightening torque: 3 +0.5 Nm General tolerances according to ISO 2768cL Dimensions in mm Please read Cautions and warnings and Important notes at the end of this document. Page 3 of 13 Feedthrough components B85121A*250, E750 ∅ 20 mm, 25 A, 75 A Capacitors Feedthrough capacitors ∅ 20 mm Technical data and measuring conditions Rated voltage VR Rated current IR Capacitance tolerance Climatic category (IEC 60068-1) 250 V AC … 440 V AC (50/60 Hz) / 600 V DC Referred to 40 °C rated temperature (B85121A*E750 referred to 50 °C rated temperature) Reduced current values at 400 Hz ±20% 40/085/56 (40 °C/+85 °C/56 days damp heat test) Screw cap fixing M12 × 0.75 Approvals UL 60384-14, 250 V AC pending1) 1) UL1283 approval expired in Dec. 2013 Characteristics and ordering codes IR CR A µF Vtest DC V Terminal Figure Approx. weight Ordering code Approvals g VR = 250 V AC, VR = 600 V DC 25 0.035 4000 M4 25 0.05 4000 Axial leads 75 0.1 1700 M6 VR = 440 V AC, VR = 600 V DC 25 0.05 4000 Axial leads 1 2 3 60 60 70 B85121A2353A250 B85121A2503B250 B85121A2104E750 P P P 2 60 B85121A4503B250 P P = Approval pending Insertion loss (dB); typical values at 50 Ω CR (µF) 10 kHz 100 kHz 1 MHz 10 MHz 100 MHz > 300 MHz 0.035  1 12 32 55 > 90 2 18 35 60 > 90 5 22 40 70 > 90 0.05 0.1   Please read Cautions and warnings and Important notes at the end of this document. Page 4 of 13 Feedthrough components B85121A*250, E750 ∅ 20 mm, 25 A, 75 A Capacitors Dimensional drawings Figure 1, B85121A2353A250 Thread Tightening torque M4 1.2 +0.1 Nm M12 × 0.75 4.0 +0.5 Nm General tolerances according to ISO 2768cL Dimensions in mm Figure 2, B85121A*B250 Tightening torque: 4 +0.5 Nm General tolerances according to ISO 2768cL Dimensions in mm Figure 3, B85121A2104E750 Thread Tightening torque M6 3 +0.1 Nm M12 × 0.75 4 +0.5 Nm General tolerances according to ISO 2768cL Dimensions in mm Please read Cautions and warnings and Important notes at the end of this document. Page 5 of 13 Feedthrough components B85121A*A250, A750 ∅ 30 mm, 25 A, 75 A Capacitors Feedthrough capacitors ∅ 30 mm Technical data and measuring conditions Rated voltage VR Rated current IR Capacitance tolerance Climatic category (IEC 60068-1) 250 V AC (50/60 Hz) / 600 V DC Referred to 40 °C rated temperature Reduced current values at 400 Hz ±20% 40/085/56 (40 °C/+85 °C/56 days damp heat test) Screw cap fixing M20 × 1 Approvals UL 60384-14, 250 V AC pending1) 1) UL1283 approval expired in Dec. 2013 Characteristics and ordering codes IR A CR µF Terminal Approx. weight g VR = 250 V AC, VR = 600 V DC, Vtest = 2000 V DC 25 1.0 M6 180 75 1.0 M6 180 Ordering code Approvals B85121A2105A250 B85121A2105A750 P P P = Approval pending Insertion loss (dB); typical values at 50 Ω CR (µF) 10 kHz 100 kHz 1 MHz 10 MHz 100 MHz 1 GHz 1.0 5 25 45 50 85 > 90 Dimensional drawing Thread M6 M20 × 1 Tightening torque 3 +0.5 Nm 10 +1 Nm General tolerances according to ISO 2768cL Dimensions in mm Please read Cautions and warnings and Important notes at the end of this document. Page 6 of 13 Feedthrough components B85121A*A630, A101, A201 ∅ 55 mm, 63 A ... 200 A Capacitors Feedthrough capacitors ∅ 55 mm Technical data and measuring conditions Rated voltage VR Rated current IR Capacitance tolerance Climatic category (IEC 60068-1) 250 V AC (50/60 Hz) / 600 V DC Referred to 40 °C rated temperature Reduced current values at 400 Hz ±20% 40/085/56 (40 °C/+85 °C/56 days damp heat test) Screw cap fixing M32 × 1.5 Approvals UL 60384-14, 250 V AC pending1) 1) UL1283 approval expired in Dec. 2013 Characteristics and ordering codes IR CR A µF Vtest DC V Terminal VR = 250 V AC, VR = 600 V DC 63 0.5 3000 M6 63 1.0 2500 M6 63 2.0 2500 M6 63 4.7 2000 M6 100 0.5 3000 M8 100 1.0 2500 M8 100 2.0 2500 M8 100 4.7 2000 M8 200 0.5 3000 M10 200 1.0 2500 M10 200 2.0 2500 M10 200 4.7 2000 M10 Dimensions l+1 l1-1 l2-3 mm Approx. weight g Ordering code Approvals 30 30 60 60 30 30 60 60 30 30 60 60 250 250 300 300 250 250 300 300 250 250 350 350 B85121A2504A630 B85121A2105A630 B85121A2205A630 B85121A2475A630 B85121A2504A101 B85121A2105A101 B85121A2205A101 B85121A2475A101 B85121A2504A201 B85121A2105A201 B85121A2205A201 B85121A2475A201 P P P P P P P P P P P P 100 100 130 130 110 110 140 140 120 120 150 150 50 50 50 50 53 53 53 53 59 59 59 59 P = Approval pending Insertion loss (dB); typical values at 50 Ω CR (µF) 10 kHz 100 kHz 1 MHz 10 MHz 100 MHz 1 GHz 0.5 2 15 35 40 80 > 90 1.0 5 25 45 50 85 > 90 2.0 10 30 50 55 > 90 > 90 4.7 15 35 55 65 > 90 > 90 Please read Cautions and warnings and Important notes at the end of this document. Page 7 of 13 Feedthrough components B85121A*A630, A101, A201 ∅ 55 mm, 63 A ... 200 A Capacitors Dimensional drawing General tolerances according to ISO 2768cL Dimensions in mm Thread Tightening torque M6 3 +0.5 Nm M8 5 +0.5 Nm M10 8 +2 Thread Tightening torque M32 × 1.5 24 +2.5 Nm Nm Please read Cautions and warnings and Important notes at the end of this document. Page 8 of 13 Feedthrough components B85121 Capacitors Cautions and warnings Please read all safety and warning notes carefully before installing the EMC filter and putting it into operation (see ). The same applies to the warning signs on the filter. Please ensure that the signs are not removed nor their legibility impaired by external influences. Death, serious bodily injury and substantial material damage to equipment may occur if the appropriate safety measures are not carried out or the warnings in the text are not observed. Using according to the terms The EMC filters may be used only for their intended application within the specified values in lowvoltage networks in compliance with the instructions given in the data sheets and the data book. The conditions at the place of application must comply with all specifications for the filter used. Warning It shall be ensured that only qualified persons (electricity specialists) are engaged on work such as planning, assembly, installation, operation, repair and maintenance. They must be provided with the corresponding documentation. Danger of electric shock. EMC filters contain components that store an electric charge. Dangerous voltages can continue to exist at the filter terminals for longer than five minutes even after the power has been switched off. The protective earth connections shall be the first to be made when the EMC filter is installed and the last to be disconnected. Depending on the magnitude of the leakage currents, the particular specifications for making the protective-earth connection must be observed. Impermissible overloading of the EMC filter or filter, such as with circuits able to cause resonances, impermissible voltages at higher frequencies etc. can lead to bodily injury and death as well as cause substantial material damages (e.g. destruction of the filter housing). EMC filters and filters must be protected in the application against impermissible exceeding of the rated currents by overcurrent protective circuitry. In case of leakage currents >3.5 mA you shall mount the PE conductor stationary with the required cross section before beginning of operation and save it against disconnecting. For leakage currents IL1) 250 A Instructions Reference chapter (data book), paragraph For operating currents greater than 250 A, we Mounting recommend the PE connection to be set up between instructions, point the feed (filter: line) and output (filter: load) not via the 2 PE terminal bolt in the filter housing. Mounting position Note the mounting position of the filters! It must Mounting always be ensured that natural convection is not instructions, point impaired. 13 Long motor cables Long motor cables cause parasitic currents in the installation. The cable lengths indicated for the output chokes and output filters serve for orientation. The user must check the technical parameters and especially the choke temperatures for the respective application. Mounting instructions, point 15 Display of ordering codes for EPCOS products The ordering code for one and the same product can be represented differently in data sheets, data books, other publications and the website of EPCOS, or in order-related documents such as shipping notes, order confirmations and product labels. The varying representations of the ordering codes are due to different processes employed and do not affect the specifications of the respective products. Detailed information can be found on the Internet under www.epcos.com/orderingcodes Please read Cautions and warnings and Important notes at the end of this document. Page 11 of 13 Feedthrough components B85121 Capacitors Symbols and terms Symbol English α Insertion loss CR Rated capacitance CX Capacitance X capacitor CY Capacitance Y capacitor ∆V Voltage drop (input to output) dv/dt Rate of voltage rise f Frequency fM Converter output frequency fP Pulse frequency fR Rated frequency fres Resonant frequency IC Current through capacitor ILK Filter leakage current Imax Maximum current IN Nominal current Iop Operating current (design current) Ipk Rated peak withstand current Iq Capacitive reactive current IR Rated current IS Interference current L Inductance LR Rated inductance Lstray Stray inductance PL Power loss R Resistance Ris Insulation resistance Rtyp DC resistance, typical value TA Ambient temperature Tmax Upper category temperature Tmin Lower category temperature TR Rated temperature uk Refered voltage drop in % Veff RMS voltage VK Voltage drop VLE Voltage line to earth; voltage line to ground VN Nominal voltage VR Rated voltage Vpeak Peak voltage Vtest Test voltage VX Voltage over X capacitor VY Voltage over Y capacitor XL Inductive reactance Z Impedance |Z| Impedance, absolute value Please read Cautions and warnings and Important notes at the end of this document. Page 12 of 13 German Einfügungsdämpfung Bemessungskapazität Kapazität X-Kondensator Kapazität Y-Kondensator Spannungsabfall im Filter Spannungsanstiegsgeschwindigkeit Frequenz Motorfrequenz Pulsfrequenz Bemessungsfrequenz Resonanzfrequenz Strom durch Kondensator Filter-Ableitstrom Maximalstrom Nennstrom Betriebsstrom Bemessungs-Stoßstromfestigkeit Kapazitiver Blindstrom Bemessungsstrom Störstrom Induktivität Bemessungsinduktivität Streuinduktivität Verlustleistung Widerstand Isolationswiderstand Gleichstromwiderstand, Richtwert Umgebungstemperatur Obere Kategorietemperatur Untere Kategorietemperatur Bemessungstemperatur Bezogener Spannungsabfall in % Effektivspannung Spannungsabfall Spannung Phase zu Erdpotential Nennspannung Bemessungsspannung Spitzenspannung Prüfspannung Spannung über X-Kondensator Spannung über Y-Kondensator Induktiver Blindwiderstand Scheinwidertand Scheinwiderstand (Betragswert) Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule we are either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether a product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.tdk-electronics.tdk.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to our General Terms and Conditions of Supply. 7. Our manufacturing sites serving the automotive business apply the IATF 16949 standard. The IATF certifications confirm our compliance with requirements regarding the quality management system in the automotive industry. Referring to customer requirements and customer specific requirements (“CSR”) TDK always has and will continue to have the policy of respecting individual agreements. Even if IATF 16949 may appear to support the acceptance of unilateral requirements, we hereby like to emphasize that only requirements mutually agreed upon can and will be implemented in our Quality Management System. For clarification purposes we like to point out that obligations from IATF 16949 shall only become legally binding if individually agreed upon. 8. The trade names EPCOS, CeraCharge, CeraDiode, CeraLink, CeraPad, CeraPlas, CSMP, CTVS, DeltaCap, DigiSiMic, ExoCore, FilterCap, FormFit, LeaXield, MiniBlue, MiniCell, MKD, MKK, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, PowerHap, PQSine, PQvar, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.tdk-electronics.tdk.com/trademarks. Release 2018-10 Page 13 of 13