MF1408-01a
CMOS 4-BIT SINGLE CHIP MICROCOMPUTER
S5U1C63000P Manual
(S1C63 Family Peripheral Circuit Board)
NOTICE
No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko
Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any
liability of any kind arising out of any inaccuracies contained in this material or due to its application or use in any product or
circuit and, further, there is no representation that this material is applicable to products requiring high level reliability, such
as medical products. Moreover, no license to any intellectual property rights is granted by implication or otherwise, and there
is no representation or warranty that anything made in accordance with this material will be free from any patent or copyright
infringement of a third party. This material or portions thereof may contain technology or the subject relating to strategic
products under the control of the Foreign Exchange and Foreign Trade Law of Japan and may require an export license from
the Ministry of International Trade and Industry or other approval from another government agency.
MS-DOS, Windows, Windows 95, Windows 98 and Windows NT are registered trademarks of Microsoft Corporation, U.S.A.
PC-DOS, PC/AT, PS/2, VGA, EGA and IBM are registered trademarks of International Business Machines Corporation, U.S.A.
NEC PC-9800 Series and NEC are registered trademarks of NEC Corporation.
All other product names mentioned herein are trademarks and/or registered trademarks of their respective owners.
© SEIKO EPSON CORPORATION 2001 All rights reserved.
New configuration of product number
Starting April 1, 2001, the configuration of product number descriptions will be changed as listed
below. To order from April 1, 2001 please use these product numbers. For further information, please
contact Epson sales representative.
Devices
S1
C
63158
F
0A01
00
Packing specification
Specification
Package (D: die form; F: QFP)
Model number
Model name (C: microcomputer, digital products)
Product classification (S1: semiconductor)
Development tools
C
63000
S5U1
A1
1
00
Packing specification
Version (1: Version 1)
Tool type (A1: Assembler Package)
Corresponding model number
(63000: common to S1C63 Family)
Tool classification (C: microcomputer use)
Product classification
(S5U1: development tool for semiconductor products)
CONTENTS
S5U1C63000P Manual (S1C63 Family Peripheral Circuit Board)
This manual describes how to use the S1C63 Family Peripheral Circuit Board (S5U1C63000P). This circuit
board is used to provide emulation functions when it is installed in the ICE (S5U1C63000H1/
S5U1C63000H2), a debugging tool for the 4-bit Single Chip Microcomputer S1C63 Family.
This manual describes only the common specifications of the S1C63 Family Peripheral Circuit Board
(S5U1C63000P), so refer to the S5U1C63000P Manual (Peripheral Circuit Board for S1C63xxx) for the model
dependent specifications. For details on ICE functions and how to operate the debugger, refer to the
separately prepared manuals.
Contents
CHAPTER
1 INTRODUCTION ____________________________________________ 1
1.1
1.2
1.3
CHAPTER
2 SETTING UP THE S5U1C63000P _____________________________ 2
2.1
2.2
2.3
CHAPTER
Outline of S5U1C63000P ............................................................................. 1
Components of S5U1C63000P ..................................................................... 1
External View of S5U1C63000P ................................................................... 1
Installing the S5U1C63000P in the ICE (S5U1C63000H1/S5U1C63000H2) ....... 2
Downloading Cricuit Data 1 – when new ICE (S5U1C63000H2) is used .............. 3
Downloading Cricuit Data 2 – when previous ICE (S5U1C63000H1) is used ....... 3
3 PRODUCT SPECIFICATIONS ___________________________________ 4
S5U1C63000P MANUAL
(S1C63 FAMILY PERIPHERAL CIRCUIT BOARD)
EPSON
i
CHAPTER 1: INTRODUCTION
CHAPTER 1
INTRODUCTION
1.1 Outline of S5U1C63000P
The S5U1C63000P provides on a board all the peripheral circuits of S1C63 Family microcomputers other
than the core CPU. By installing this board in the ICE (S5U1C63000H1/S5U1C63000H2) you can use it to
emulate each model in the S1C63 Family. This board contains a programmable gate array (FPGA) and
supports each model by downloading the circuit data from the host PC to the FPGA via the ICE.
1.2 Components of S5U1C63000P
After unpacking your S5U1C63000P package, check to see that all of the following components are
included.
(1) S5U1C63000P main unit .............................................................................................. 1 board
(2) I/O cable (80-pin/40-pin × 2 flat type) .................................................................... 1 pair
(3) I/O cable (100-pin/50-pin × 2 flat type) .................................................................. 1 pair
(4) Connector for connecting to target system (40-pin) ............................................... 2 pieces
(5) Connector for connecting to target system (50-pin) ............................................... 2 pieces
(6) Warranty card ............................................................................................................... 1 card
(7) User registration card .................................................................................................. 1 card
(8) Precautions on Using the S5U1C63000P Peripheral Circuit Board ..................... 1 sheet
(9) S5U1C63000P Manual (S1C63 Family Peripheral Circuit Board) ........................ 1 copy
1.3 External View of S5U1C63000P
IOSEL2
CLK
VLCD VSVD
D E
VC5
1 3
XC4062XLA
RESET
PRG
Fig. 1.3.1 External view of S5U1C63000P
S5U1C63000P MANUAL
(S1C63 FAMILY PERIPHERAL CIRCUIT BOARD)
EPSON
1
CHAPTER 2: SETTING UP THE S5U1C63000P
CHAPTER 2
SETTING UP THE S5U1C63000P
2.1 Installing the S5U1C63000P in the ICE (S5U1C63000H1/S5U1C63000H2)
(1) Unfasten the screws located on the left and right sides of the front panel of the ICE (S5U1C63000H1/
S5U1C63000H2) by turning them counterclockwise, then remove the front panel.
(2) Insert the S5U1C63000P board into the ICE along the its uppermost guide rails until the tip of the board
touches the back of the ICE. If some other board is mounted on the uppermost guide rails, remove that
board by using the jig supplied with the ICE before you insert the S5U1C63000P board (see Figure 2.1.3).
(3) Once the S5U1C63000P board has been inserted almost fully into the ICE, secure it in position by
using the jig supplied with the ICE (see Figure 2.1.2).
(4) When the above is done, replace the front panel.
(1), (4)
(2)
S5U1C63000P board
(3)
Fig. 2.1.1 Installing the S5U1C63000P board in the ICE (S5U1C63000H1/S5U1C63000H2)
• Installing the S5U1C63000P board
Set the jig included with the ICE into position as
shown in Figure 2.1.2. Using this jig as a lever,
push it toward the inside of the board evenly on
the left and right sides. After confirming that the
S5U1C63000P board has been firmly fitted into the
internal slot of the ICE, remove the jig.
S5U1C63000P board
Fig. 2.1.2
Installing the S5U1C63000P board
• Dismounting the S5U1C63000P board
Set the jig included with the ICE into position as
shown in Figure 2.1.3. Using this jig as a lever,
push it toward the outside of the board evenly on
the left and right sides. After confirming that the
S5U1C63000P board has been dismounted from
the backboard connector, pull the S5U1C63000P
board out of the ICE.
S5U1C63000P board
Fig. 2.1.3
Dismounting the S5U1C63000P board
2
EPSON
S5U1C63000P MANUAL
(S1C63 FAMILY PERIPHERAL CIRCUIT BOARD)
CHAPTER 2: SETTING UP THE S5U1C63000P
2.2 Downloading Circuit Data 1 – when new ICE (S5U1C63000H2) is used
This board (S5U1C63000P) comes with the FPGA that contains factory inspection data, therefore the
circuit data for the model to be used should be downloaded. The following explains the downloading
procedure.
1) Remove the ICE top cover and then set the DIP switch "IOSEL2" on this board to the "E" position.
2) Connect the ICE to the host PC. Then turn the host PC and ICE on.
3) Invoke the debugger included in the assembler package (ver. 5 or later). For how to use the ICE and
debugger, refer to the manuals supplied with the ICE and assembler package.
4) Download the circuit data file (.mot) corresponding to the model by entering the following commands
in the command window.
>XFER
>XFWR
>XFCP
(erase all)
(download the specified file)*
(compare the specified file and downloaded data)
∗ The downloading takes about 15 minutes.
5) Terminate the debugger and then turn the ICE off.
6) Set the DIP switch "IOSEL2" on this board to the "D" position.
7) Turn the ICE on and invoke the debugger again. Debugging can be started here.
2.3 Downloading Circuit Data 2 – when previous ICE (S5U1C63000H1) is used
The standard ICE (S5U1C63000H1, previous model) did not support the circuit data download function
for this board. To use the download function, update the ICE firmware according to the following
procedure.
1) Set the baud rate of the ICE to 9600 bps. Refer to the manual supplied with the ICE for setting the DIP
switch.
2) Connect the ICE to the host PC and then start up the host PC in DOS. When Windows is running,
restart in DOS mode.
Note: Do not use the DOS prompt of Windows.
3) Turn the ICE on.
4) Configure the RS232C parameters for the host PC as follows:
C:\>MODE COM1:9600,n,8,1,p
(9600 bps, 8-bit data, 1 stop bit, no parity)
5) Copy the following files included in the assembler package (ver. 5 or later) to a directory on the hard disk.
tm63.exe, ice63.com, i63com.o, i63par
6) Move to the directory in Step 5, run the TM63. TM63 enters command ready status after invocation,
enter a command as follows:
C:\>tm63
xat
________
TM63 start on IBM PC
TM63 start V01.01
>dlf
ice63.com i63com.o i63par 0b
________________________________
...
>q
_
7) Enter "q" to terminate TM63 after the prompt mark is displayed.
8) The ICE firmware is now updated. Turn the ICE off and then download the circuit data by the procedure described in Section 2.2.
S5U1C63000P MANUAL
(S1C63 FAMILY PERIPHERAL CIRCUIT BOARD)
EPSON
3
CHAPTER 3: PRODUCT SPECIFICATIONS
CHAPTER 3
PRODUCT SPECIFICATIONS
The specifications of the S5U1C63000P are listed below.
S5U1C63000P
Dimension:
Weight:
Power supply:
254 mm (wide) × 144.8 mm (depth) × 13 mm (height) (including screws)
Approx. 300 g
DC 5 V ± 5%, less than 1 A (supplied from ICE main unit)
I/O connection cable (80-pin)
S5U1C63000P connector:
Cable connector (80-pin):
Cable connector (40-pin):
Cable:
Interface:
Length:
KEL8830E-080-170L
KEL8822E-080-171
3M7940-6500SC
40-pin flat cable
CMOS interface (3.3 V)
Approx. 40 cm
1 pair
1 pair
I/O connection cable (100-pin)
S5U1C63000P connector:
Cable connector (100-pin):
Cable connector (50-pin):
Cable:
Interface:
Length:
KEL8830E-100-170L
KEL8822E-100-171
3M7950-6500SC
50-pin flat cable
CMOS interface (3.3 V)
Approx. 40 cm
1 pair
1 pair
Accessories
40-pin connector for connecting to target system:
3M3432-6002LCSC × 2
50-pin connector for connecting to target system:
3M3433-6002LCSC × 2
4
EPSON
S5U1C63000P MANUAL
(S1C63 FAMILY PERIPHERAL CIRCUIT BOARD)
International Sales Operations
AMERICA
ASIA
EPSON ELECTRONICS AMERICA, INC.
EPSON (CHINA) CO., LTD.
- HEADQUARTERS -
23F, Beijing Silver Tower 2# North RD DongSanHuan
ChaoYang District, Beijing, CHINA
Phone: 64106655
Fax: 64107319
150 River Oaks Parkway
San Jose, CA 95134, U.S.A.
Phone: +1-408-922-0200
Fax: +1-408-922-0238
SHANGHAI BRANCH
4F, Bldg., 27, No. 69, Gui Jing Road
Caohejing, Shanghai, CHINA
Phone: 21-6485-5552
Fax: 21-6485-0775
- SALES OFFICES West
1960 E. Grand Avenue
EI Segundo, CA 90245, U.S.A.
Phone: +1-310-955-5300
Fax: +1-310-955-5400
Central
101 Virginia Street, Suite 290
Crystal Lake, IL 60014, U.S.A.
Phone: +1-815-455-7630
Fax: +1-815-455-7633
Northeast
301 Edgewater Place, Suite 120
Wakefield, MA 01880, U.S.A.
Phone: +1-781-246-3600
Fax: +1-781-246-5443
EPSON HONG KONG LTD.
20/F., Harbour Centre, 25 Harbour Road
Wanchai, Hong Kong
Phone: +852-2585-4600 Fax: +852-2827-4346
Telex: 65542 EPSCO HX
EPSON TAIWAN TECHNOLOGY & TRADING LTD.
10F, No. 287, Nanking East Road, Sec. 3
Taipei
Phone: 02-2717-7360
Fax: 02-2712-9164
Telex: 24444 EPSONTB
HSINCHU OFFICE
Southeast
3010 Royal Blvd. South, Suite 170
Alpharetta, GA 30005, U.S.A.
Phone: +1-877-EEA-0020 Fax: +1-770-777-2637
13F-3, No. 295, Kuang-Fu Road, Sec. 2
HsinChu 300
Phone: 03-573-9900
Fax: 03-573-9169
EPSON SINGAPORE PTE., LTD.
No. 1 Temasek Avenue, #36-00
Millenia Tower, SINGAPORE 039192
Phone: +65-337-7911
Fax: +65-334-2716
EUROPE
EPSON EUROPE ELECTRONICS GmbH
SEIKO EPSON CORPORATION KOREA OFFICE
- HEADQUARTERS Riesstrasse 15
80992 Munich, GERMANY
Phone: +49-(0)89-14005-0
Fax: +49-(0)89-14005-110
SALES OFFICE
Altstadtstrasse 176
51379 Leverkusen, GERMANY
Phone: +49-(0)2171-5045-0
Fax: +49-(0)2171-5045-10
UK BRANCH OFFICE
Unit 2.4, Doncastle House, Doncastle Road
Bracknell, Berkshire RG12 8PE, ENGLAND
Phone: +44-(0)1344-381700
Fax: +44-(0)1344-381701
50F, KLI 63 Bldg., 60 Yoido-dong
Youngdeungpo-Ku, Seoul, 150-763, KOREA
Phone: 02-784-6027
Fax: 02-767-3677
SEIKO EPSON CORPORATION
ELECTRONIC DEVICES MARKETING DIVISION
Electronic Device Marketing Department
IC Marketing & Engineering Group
421-8, Hino, Hino-shi, Tokyo 191-8501, JAPAN
Phone: +81-(0)42-587-5816
Fax: +81-(0)42-587-5624
ED International Marketing Department Europe & U.S.A.
FRENCH BRANCH OFFICE
1 Avenue de l' Atlantique, LP 915 Les Conquerants
Z.A. de Courtaboeuf 2, F-91976 Les Ulis Cedex, FRANCE
Phone: +33-(0)1-64862350
Fax: +33-(0)1-64862355
BARCELONA BRANCH OFFICE
Barcelona Design Center
Edificio Testa, Avda. Alcalde Barrils num. 64-68
E-08190 Sant Cugat del Vallès, SPAIN
Phone: +34-93-544-2490
Fax: +34-93-544-2491
421-8, Hino, Hino-shi, Tokyo 191-8501, JAPAN
Phone: +81-(0)42-587-5812
Fax: +81-(0)42-587-5564
ED International Marketing Department Asia
421-8, Hino, Hino-shi, Tokyo 191-8501, JAPAN
Phone: +81-(0)42-587-5814
Fax: +81-(0)42-587-5110
S5U1C63000P Manual
(S1C63 Family Peripheral Circuit Board)
ELECTRONIC DEVICES MARKETING DIVISION
EPSON Electronic Devices Website
http://www.epson.co.jp/device/
Issue May, 2001
Printed in Japan M A
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Epson:
S5U1C63000P6100
