F49L800BA

ESMT 1. FEATURES Single supply voltage 2.7V-3.6V Fast access time: 70/90 ns 1,048,576x8 / 524,288x16 switchable by BYTE pin Compatible with JEDEC standard - Pin-out, packages and software commands compatible with single-power supply Flash Low power consumption - 7mA typical active current - 25uA typical standby current  100,000 program/erase cycles typically 20 years data retention Command register architecture - Byte programming (9us typical) - Sector Erase(sector structure: one 16 KB, two 8 KB, one 32 KB, and fifteen 64 KB)  Auto Erase (chip & sector) and Auto Program - Any combination of sectors can be erased concurrently; Chip erase also provided. - Automatically program and verify data at specified address Erase Suspend/Erase Resume - Suspend or Resume erasing sectors to allow the read/program in another sector F49L800UA/F49L800BA 8 Mbit (1M x 8/512K x 16) 3V Only CMOS Flash Memory Ready/Busy (RY/ BY ) - RY/ BY output pin for detection of program or erase operation completion End of program or erase detection - Data polling - Toggle bits Hardware reset - Hardware pin( RESET ) resets the internal state machine to the read mode Sector Protection /Unprotection - Hardware Protect/Unprotect any combination of sectors from a program or erase operation. Low VCC Write inhibit is equal to or less than 2.0V Boot Sector Architecture - U = Upper Boot Block - B = Bottom Boot Block Packages available: - 48-pin TSOPI - All Pb-free products are RoHS-Compliant 2. ORDERING INFORMATION Part No F49L800UA-70TG F49L800BA-70TG Boot Upper Bottom Speed 70 ns 70 ns Package TSOPI TSOPI Comments Pb-free Pb-free Part No F49L800UA-90TG F49L800BA-90TG Boot Upper Bottom Speed 90 ns 90 ns Package TSOPI TSOPI Comments Pb-free Pb-free 3. GENERAL DESCRIPTION The F49L800UA/F49L800BA is a 8 Megabit, 3V only CMOS Flash memory device organized as 1M bytes of 8 bits or 512K words of 16bits. This device is packaged in standard 48-pin TSOP. It is designed to be programmed and erased both in system and can in standard EPROM programmers. With access times of 70 ns and 90 ns, the F49L800UA/F49L800BA allows the operation of high-speed microprocessors. The device has separate chip enable CE , write enable WE , and output enable OE controls. ESMT's memory devices reliably store memory data even after 100,000 program and erase cycles. The F49L800UA/F49L800BA is entirely pin and command set compatible with the JEDEC standard for 8 Megabit Flash memory devices. Commands are written to the command register using standard microprocessor write timings. The F49L800UA/F49L800BA features a sector erase architecture. The device memory array is divided into one 16 Kbytes, two 8 Kbytes, one 32 Kbytes, and fifteen 64 Kbytes. Sectors can be erased individually or in groups without affecting the data in other sectors. Multiple-sector erase and whole chip erase capabilities provide the flexibility to revise the data in the device. The sector protect/unprotect feature disables both program and erase operations in any combination of the sectors of the memory. This can be achieved in-system or via programming equipment. A low VCC detector inhibits write operations on loss of power. End of program or erase is detected by the Ready/Busy status pin, Data Polling of DQ7, or by the Toggle Bit I feature on DQ6. Once the program or erase cycle has been successfully completed, the device internally resets to the Read mode. Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 1/47 ESMT 4. PIN CONFIGURATIONS 4.1 48-pin TSOP F49L800UA/F49L800BA A15 A14 A13 A12 A11 A10 A9 A8 NC NC WE RESET NC NC RY/BY A18 A17 A7 A6 A5 A4 A3 A2 A1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 A16 BYTE GND DQ15/A-1 DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VCC DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE GND CE A0 F49L800U/BA 4.2 Pin Description Symbol Pin Name Address Input Data Input/Output Q15 (Word mode) / LSB addr (Byte Mode) Chip Enable Output Enable Write Enable Reset Word/Byte selection input Ready/Busy Power Supply Ground No connection Functions To provide memory addresses. To output data when Read and receive data when Write. The outputs are in tri-state when OE or CE is high. To bi-direction date I/O when BYTE is High To input address when BYTE is Low To activate the device when CE is low. To gate the data output buffers. To control the Write operations. Hardware Reset Pin/Sector Protect Unprotect To select word mode or byte mode To check device operation status To provide power A0~A18 DQ0~DQ14 DQ15/A-1 CE OE WE RESET BYTE RY/ BY VCC GND NC Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 2/47 ESMT 5. SECTOR STRUCTURE Sector SA0 SA1 SA2 SA3 SA4 SA5 SA6 SA7 SA8 SA9 SA10 SA11 SA12 SA13 SA14 SA15 SA16 SA17 Sector Size Byte Mode 64Kbytes 64Kbytes 64Kbytes 64Kbytes 64Kbytes 64Kbytes 64Kbytes 64Kbytes 64Kbytes 64Kbytes 64Kbytes 64Kbytes 64Kbytes 64Kbytes 64Kbytes 32Kbytes 8Kbytes 8Kbytes Word Mode 32Kwords 32Kwords 32Kwords 32Kwords 32Kwords 32Kwords 32Kwords 32Kwords 32Kwords 32Kwords 32Kwords 32Kwords 32Kwords 32Kwords 32Kwords 16Kwords 4Kwords 4Kwords Address range Byte Mode(x8) 00000H-0FFFFH 10000H-1FFFFH 20000H-2FFFFH 30000H-3FFFFH 40000H-4FFFFH 50000H-5FFFFH 60000H-6FFFFH 70000H-7FFFFH 80000H-8FFFFH 90000H-9FFFFH A0000H-AFFFFH B0000H-BFFFFH C0000H-CFFFFH D0000H-DFFFFH E0000H-EFFFFH F0000H-F7FFFH F8000H-F9FFFH FA000H-FBFFFH F49L800UA/F49L800BA Table 1: F49L800UA Sector Address Table Sector Address 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 1 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 1 1 X X X X X X X X X X X X X X X 0 1 1 1 X X X X X X X X X X X X X X X X 0 0 1 X X X X X X X X X X X X X X X X 0 1 X Word Mode(x16) A18 A17 A16 A15 A14 A13 A12 00000H-07FFFH 08000H-0FFFFH 10000H-17FFFH 18000H-1FFFFH 20000H-27FFFH 28000H-2FFFFH 30000H-37FFFH 38000H-3FFFFH 40000H-47FFFH 48000H-4FFFFH 50000H-57FFFH 58000H-5FFFFH 60000H-67FFFH 68000H-6FFFFH 70000H-77FFFH 78000H-7BFFFH 7C000H-7CFFFH 7D000H-7DFFFH SA18 16Kbytes 8Kwords FC000H-FFFFFH 7E000H-7FFFFH 1 Note: Byte Mode: address range A18:A-1, Word mode : address range A18:A0 Table 2: F49L800BA Sector Address Table Sector SA0 SA1 SA2 SA3 SA4 SA5 SA6 SA7 SA8 SA9 SA10 SA11 SA12 SA13 SA14 SA15 SA16 SA17 SA18 Sector Size Byte Mode 16Kbytes 8Kbytes 8Kbytes 32Kbytes 64Kbytes 64Kbytes 64Kbytes 64Kbytes 64Kbytes 64Kbytes 64Kbytes 64Kbytes 64Kbytes 64Kbytes 64Kbytes 64Kbytes 64Kbytes 64Kbytes 64Kbytes Word Mode 8Kwords 4Kwords 4Kwords 16Kwords 32Kwords 32Kwords 32Kwords 32Kwords 32Kwords 32Kwords 32Kwords 32Kwords 32Kwords 32Kwords 32Kwords 32Kwords 32Kwords 32Kwords 32Kwords Address range Byte Mode(x8) 00000H-03FFFH 04000H-05FFFH 06000H-07FFFH 08000H-0FFFFH 10000H-1FFFFH 20000H-2FFFFH 30000H-3FFFFH 40000H-4FFFFH 50000H-5FFFFH 60000H-6FFFFH 70000H-7FFFFH 80000H-8FFFFH 90000H-9FFFFH A0000H-AFFFFH B0000H-BFFFFH C0000H-CFFFFH D0000H-DFFFFH E0000H-EFFFFH F0000H-FFFFFH 00000H-01FFFH 02000H-02FFFH 03000H-03FFFH 04000H-07FFFH 08000H-0FFFFH 10000H-17FFFH 18000H-1FFFFH 20000H-27FFFH 28000H-2FFFFH 30000H-37FFFH 38000H-3FFFFH 40000H-47FFFH 48000H-4FFFFH 50000H-57FFFH 58000H-5FFFFH 60000H-67FFFH 68000H-6FFFFH 70000H-77FFFH 78000H-7FFFFH 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 Sector Address 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 0 0 1 X X X X X X X X X X X X X X X 0 1 1 X X X X X X X X X X X X X X X X X 0 1 X X X X X X X X X X X X X X X X Word Mode(x16) A18 A17 A16 A15 A14 A13 A12 Note: Byte Mode: address range A18:A-1, Word mode : address range A18:A0 Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 3/47 ESMT 6. FUNCTIONAL BLOCK DIAGRAM F49L800UA/F49L800BA BYTE CE OE WE RES ET CONTROL INPUT LOGIC PROGRAM / ERASE HIGH VOLTAGE WRITE STATE MACHING (WSM) STATE REGISTER F49L800U/BA X-DECODER A0~A18 ADDRESS LATCH AND BUFFER FLASH ARRAY ARRAY SOURCE HV Y-PASS GATE COMMAND DATA DECODER SENSE AMPLIFIER Y-DECODER PGM DATA HV COMMAND DATA LATCH PROGRAM DATA LATCH DQ0~DQ15(A-1) I / O BUFFER Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 4/47 ESMT 7. FUNCTIONAL DESCRIPTION 7.1 Device operation This section describes the requirements and use of the device bus operations, which are initiated through the internal command register. The register is composed of latches that store the command, address and data information needed to execute the command. The contents of the F49L800UA/F49L800BA register serve as inputs to the internal state machine. The state machine outputs dictate the function of the device. The F49L800UA /F49L800BA features various bus operations as Table 3. Table 3. F49L800UA/F49L800BA Operation Modes Selection ADDRESS DESCRIPTION CE OE WE RESET A18 A11 DQ8~DQ15 A8 A5 DQ0~DQ7 BYTE | | | | A9 A6 A1 A0 =VIH A12 A10 A7 A2 BYTE =VIL High Z DQ8~DQ14= Reset(3) Read Write Output Disable Standby Sector Protect(2) Sector Unprotect(2) Temporary sector unprotect X L L L VCC± 0.3V L L X X L H H X H H X X H L H X L L X L, Vss± 0.3V(3) H H H VCC± 0.3V VID VID VID SA SA X X X X X X X AIN AIN X X L H X X H H L L High Z Dout DIN High Z High Z DIN DIN DIN High Z Dout DIN High Z High Z X X DIN High Z DQ15=A-1 High Z High Z X X High Z AIN See Table 4 Auto-select Notes: 1. L= Logic Low = VIL, H= Logic High = VIH, X= Don't Care, SA= Sector Address, VID=10V to 10.5V. AIN= Address In, DIN = Data In, Dout = Data Out. 2. The sector protect and unprotect functions may also be implemented via programming equipment. 3. See “Reset Mode” section. Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 5/47 ESMT Description Mode CE OE WE F49L800UA/F49L800BA Table 4. F49L800UA/F49L800BA Auto-Select Mode (High Voltage Method) A18 to A12 X A11 to A10 X A9 A8 to A7 X A6 A5 to A4 X A3 L L H H X A2 L H L H X A1 A0 DQ8 to DQ15 X 22H X X VID X L X L H X X L X X X L H 22H X X L L H SA X VID X L X X X H L X DAH 5BH 5BH 01H (protected) 00H (unprotected) DQ7 to DQ0 8CH 7FH 7FH 7FH DAH Manufacturer ID: ESMT L L L L L L L L L L H H H H H VID L L L Device ID: F49L800UA (Upper Boot Block) Device ID: F49L800BA (Bottom Boot Block) Word Byte Word Byte X X VID Sector Protection Verification L= Logic Low=VIL, H= Logic High=VIH, SA= Sector Address, X= Don’t care. Notes : 1.Manufacturer and device codes may also be accessed via the software command sequence in Table 5. Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 6/47 ESMT Reset Mode : Hardware Reset When the RESET pin is driven low for at least a period of tRP, the device immediately terminates any operation in progress, tri-states all output pins, and ignores all read/write commands for the duration of the RESET pulse. The device also resets the internal state machine to reading array data. The operation that was interrupted should be reinitiated later once the device is ready to accept another command sequence, to ensure the data integrity. The current is reduced for the duration of the RESET pulse. When RESET is held at VSS±0.3V, the device draws CMOS standby current (ICC4). If RESET is held at VIL but not within VSS±0.3V, the standby current will be greater. The RESET pin may be tied to system reset circuitry. A system reset would thus reset the Flash memory, enabling the system to read the boot-up firm-ware from the Flash memory. If RESET is asserted during a program or erase embedded algorithm operation, the RY/ BY pin remains a "0" (busy) until the internal reset operation is complete, which requires a time of tREADY (during Embedded Algorithms). The system can thus monitor RY/ BY to determine whether the reset operation is complete. If RESET is asserted when a program or erase operation is not executing , i.e. the RY/ BY is “1”, the reset operation is completed within a time of tREADY (not during Embedded Algorithms). The system can read data after tRH when the RESET pin returns to VIH. Refer to the AC Characteristics tables 13 for Hardware Reset section & Figure 23 for the timing diagram. F49L800UA/F49L800BA See “Read Command” section for more information. Refer to the AC Read Operations table 10 for timing specifications and to Figure 5 for the timing diagram. ICC1 in the DC Characteristics table represents the active current specification for reading array data. Write Mode To write a command or command sequence (which includes programming data to the device and erasing sectors of memory), the system must drive WE and CE to VIL, and OE to VIH. The “Program Command” section has details on programming data to the device using standard command sequences. An erase operation can erase one sector, multiple sectors, or the entire device. Tables 1 and 2 indicate the address space that each sector occupies. A “sector address” consists of the address bits required to uniquely select a sector. The “Software Command Definitions” section has details on erasing a sector or the entire chip, or suspending/resuming the erase operation. When the system writes the auto-select command sequence, the device enters the auto-select mode. The system can then read auto-select codes from the internal register (which is separate from the memory array) on DQ7–DQ0. Standard read cycle timings apply in this mode. Refer to the Auto-select Mode and Auto-select Command sections for more information. ICC2 in the DC Characteristics table represents the active current specification for the write mode. The “AC Characteristics” section contains timing specification tables and timing diagrams for write operations. Automatic Sleep Mode The automatic sleep mode minimizes Flash device energy consumption. The device automatically enables this mode when addresses remain unchanged for over 250ns. The automatic sleep mode is independent of the CE , WE , and OE control signals. Standard address access timings provide new data when addresses are changed. While in sleep mode, output data is latched and always available to the system. ICC4 in the DC Characteristics table represents the automatic sleep mode current specification. Read Mode To read array data from the outputs, the system must drive the CE and OE pins to VIL. CE is the power control and selects the device. OE is the output control and gates array data to the output pins. WE should remain at VIH. The internal state machine is set for reading array data upon device power-up, or after a hardware reset. This ensures that no spurious alteration of the memory content occurs during the power transition. No command is necessary in this mode to obtain array data. Standard microprocessor’s read cycles that assert valid addresses on the device address inputs produce valid data on the device data outputs. The device remains enabled for read access until the command register contents are altered. Word / Byte Mode This pin control the I/O configuration of device. When BYTE = VIH or Vcc ± 0.3V. The I/O configuration is x16 and the pin of D15/A-1 is bi-direction Data I/O. However, BYTE = VIL or VSS ± 0.3V. The I/O configuration would be x8 and The pin of DQ15/A-1 only address input pin. You must define the function of this pin before enable this device. Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 7/47 ESMT Temporary Sector Unprotect Mode This feature allows temporary unprotection of previously protected sector to change data in-system. This mode is activated by setting the RESET pin to VID(10V-10.5V). During this mode, all formerly protected sectors are F49L800UA/F49L800BA un-protected and can be programmed or erased by selecting the sector addresses. Once VID is removed from the RESET pin, all the previously protected sectors are protected again. S tart RESET = V ID ( Note 1) Perform Erase or Program Operation Operation Completed RESET = V I H Temporary Sector Unprotect Completed (Note 2) Notes: 1. All protected sectors unprotected. 2. All previously protected sectors are protected once again. Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 8/47 ESMT Output Disable Mode With the OE is at a logic high level (VIH), outputs from the devices are disabled. This will cause the output pins in a high impedance state F49L800UA/F49L800BA Figure 16 shows the algorithms and Figure 15 shows the timing diagram. This method uses standard microprocessor bus cycle timing. For sector unprotect, all unprotected sectors must first be protected prior to the first sector unprotect write cycle. The alternate method intended only for programming equipment requires VID on address pin A9, OE , and RESET . Standby Mode When CE and RESET are both held at VCC ± 0.3V, the device enter CMOS Standby mode. If CE and RESET are held at VIH, but not within the range of VCC ± 0.3V, the device will still be in the standby mode, but the standby current will be larger. Auto-select Mode The auto-select mode provides manufacturer and device identification and sector protection verification, through outputs on DQ7–DQ0. This mode is primarily intended for programming equipment to automatically match a device to be programmed with its corresponding programming algorithm. However, the auto-select codes can also be accessed in-system through the command register. When using programming equipment, this mode requires VID (10 V to 10.5 V) on address pin A9. While address pins A3, A2, A1, and A0 must be as shown in Table 4. To verify sector protection, all necessary pins have to be set as required in Table 4, the programming equipment may then read the corresponding identifier code on DQ7-DQ0. To access the auto-select codes in-system, the host system can issue the auto-select command via the command register, as shown in Table 5. This method does not require VID. See “ Software Command Definitions” for details on using the auto-select mode. If the device is deselected during auto algorithm of erasure or programming, the device draws active current ICC2 until the operation is completed. ICC3 in the DC Characteristics table represents the standby current specification. The device requires standard access time (tCE) for read access from either of these standby modes, before it is ready to read data. Sector Protect / Un-protect Mode The hardware sector protect feature disables both program and erase operations in any sector. The hardware sector unprotect feature re-enables both the program and erase operations in previously protected sectors. Sector protect/unprotect can be implemented via two methods. The primary method requires VID on the RESET pin only, and can be implemented either in-system or via programming equipment. 7.2 Software Command Definitions Writing specific address and data commands or sequences into the command register initiates the device operations. Table 5 defines the valid register command sequences. Writing incorrect address and data values or writing them in the improper sequence resets the device to reading array data. All addresses are latched on the falling edge of WE or CE , whichever happens later. All data is latched on the rising edge of WE or CE , whichever happens first. Refer to the corresponding timing diagrams in the AC Characteristics section. Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 9/47 ESMT Command Reset (5) Read (4) Program Word Byte Word Byte Word Byte Bus Cycles 1 1 4 4 6 6 6 6 1 1 1st Bus Cycle Addr XXXH RA 555H Data F0H RD AAH 2nd Bus Cycle Addr 2AAH 555H 2AAH 555H 2AAH 555H Data 55H 55H 55H 55H 55H 55H 3rd Bus Cycle Addr 555H AAAH 555H AAAH 555H AAAH - F49L800UA/F49L800BA Table 5. F49L800UA/F49L800BA Software Command Definitions 4th Bus Cycle Addr PA PA 555H Data PD PD AAH 2AAH 555H 2AAH 555H 55H 55H 55H 55H 555H AAAH SA SA 10H 10H 30H 30H 5th Bus Cycle Addr Data 6th Bus Cycle Addr Data - Data A0H A0H 80H 80H 80H 80H - AAAH AAH 555H AAH Chip Erase AAAH AAH 555H AAH AAAH AAH 555H AAH Sector Erase Sector Erase Suspend (6) AAAH AAH XXXH XXXH B0H 30H AAAH AAH - Sector Erase Resume (7) Auto-select See Table 6. X = don’t care RA = Address of memory location to be read. RD = Data to be read at location RA. PA = Address of memory location to be programmed. PD = Data to be programmed at location PA. SA = Address of the sector. Notes: 1. Except Read command and Auto-select command, all command bus cycles are write operations. 2. The system should generate the following address patterns: 555H or 2AAH to address A10~A0 in word mode / AAAH or 555H to address A10~A-1 in byte mode. 3. Address bits A19–A11 are don’t cares, unless SA or PA required. 4. The Reset command is required to return to reading array data when device is in the auto-select mode, or if DQ5 goes high (while the device is providing status data). 5. No command cycles required when reading array data. 6. The system may read and program in non-erasing sectors, or enter the auto-select mode, when in the Erase Suspend mode. The Erase Suspend command is valid only during a sector erase operation. 7. The Erase Resume command is valid only during the Erase Suspend mode. Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 10/47 ESMT Command Cycles 4 4 4 4 4 4 4 4 4 4 4 4 4 4 1st Bus Cycle Addr Data 555H AAH 555H AAH 555H AAH 555H AAH AAAH AAH AAAH AAH AAAH AAH AAAH AAH 555H AAH 555H F49L800UA/F49L800BA Table 6. F49L800UA/F49L800BA Auto-Select Command 2nd Bus Cycle Addr Data 2AAH 55H 2AAH 55H 2AAH 55H 2AAH 55H 555H 55H 555H 55H 555H 55H 555H 55H 2AAH 55H 55H 55H 55H 55H 55H 3rd Bus 4th Bus 5th Bus 6th Bus Cycle Cycle Cycle Cycle Addr Data Addr Data Addr Data Addr Data 555H 90H X00H XX8CH 555H 90H X04H XX7FH 555H 90H X08H XX7FH 555H 90H X0CH XX7FH AAAH 90H X00H 8CH AAAH 90H X04H 7FH AAAH 90H X08H 7FH AAAH 90H X0CH 7FH 555H 90H X01H 22DAH AAAH 555H AAAH 555H AAAH 90H 90H 90H 90H 90H X02H DAH X01H 225BH X02H 5BH (SA) XX00H X02H XX01H 00H (SA) X04H 01H Word Manufacturer ID Byte Word Byte Word Byte Word Sector Protect Verify Byte Device ID, Upper boot Device ID, Bottom boot AAAH AAH 555H AAH 2AAH AAAH AAH 555H 555H AAH 2AAH AAAH AAH 555H Notes : 1. The fourth cycle of the auto-select command sequence is a read cycle. 2. For Sector Protect Verify operation: If read out data is 01H, it means the sector has been protected. If read out data is 00H, it means the sector is still not being protected. Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 11/47 ESMT Reset Command Writing the reset command to the device resets the device to reading array data. Address bits are all don’t cares for this command. The reset command may be written between the sequence cycles in an erase command sequence before erasing begins. This resets the device to reading array data. Once erasure begins, however, the device ignores reset commands until the operation is complete. The reset command may be written between the sequence cycles in a program command sequence before programming begins. This resets the device to reading array data (also applies to programming in Erase Suspend mode). Once programming begins, however, the device ignores reset commands until the operation is complete. The reset command may be written between the sequence cycles in an auto-select command sequence. Once in the auto-select mode, the reset command must be written to return to reading array data (also applies to auto-select during Erase Suspend). If DQ5 goes high(see “DQ5: Exceeded Timing Limits” section) during a program or erase operation, writing the reset command returns the device to reading array data (also applies during Erase Suspend). F49L800UA/F49L800BA Program Command The program command sequence programs one byte into the device. Programming is a four-bus-cycle operation. The program command sequence is initiated by writing two unlock write cycles, followed by the program set-up command. The program address and data are written next, which in turn initiate the Embedded Program algorithm. The system is not required to provide further controls or timings. The device automatically provides internally generated program pulses and verifies the programmed cell margin. When the Embedded Program algorithm is complete, the device then returns to reading array data and addresses are no longer latched. The system can determine the status of the program operation by using DQ7, DQ6, or RY/ BY . See “Write Operation Status” section for more information on these status bits. Any commands written to the device during the Embedded Program Algorithm are ignored. Note that a hardware reset immediately terminates the programming operation. The Program command sequence should be reinitiated once the device has reset to reading array data, to ensure data integrity. Programming is allowed in any sequence and across sector boundaries. A bit cannot be programmed from a “0” back to a “1”. Attempting to do so may halt the operation and set DQ5 to “1”, or cause the Data Polling algorithm to indicate the operation was successful. However, a succeeding read will show that the data is still “0”. Only erase operations can convert a “0” to a “1”. Read Command The device is automatically set to reading array data after device power-up. No commands are required to retrieve data. The device is also ready to read array data after completing an Embedded Program or Embedded Erase algorithm. When the device accepts an Erase Suspend command, the device enters the Erase Suspend mode. The system can read array data using the standard read timings, except that if it reads an address within erase-suspended sectors, the device outputs status data. After completing a programming operation in the Erase Suspend mode, the system may once again read array data with the same exception. See “Erase Suspend/Erase Resume Commands” for more information on this mode. The system must issue the reset command to re-enable the device for reading array data if DQ5 goes high, or while in the auto-select mode. See the “Reset Command” section. See also the “Read Mode” in the “Device Operations” section for more information. Refer to Figure 5 for the timing diagram. Chip Erase Command Chip erase is a six-bus cycle operation. The chip erase command sequence is initiated by writing two unlock cycles, followed by a set-up command. Two additional unlock write cycles are then followed by the chip erase command, which in turn invokes the Embedded Erase algorithm. The device does not require the system to preprogram prior to erase. The Embedded Erase algorithm automatically preprograms and verifies the entire memory for an all zero data pattern prior to electrical erase. Any commands written to the chip during the Embedded Erase algorithm are ignored. Note that a hardware reset during the chip erase operation immediately terminates the operation. The Chip Erase command sequence should be reinitiated once the device has returned to reading array data, to ensure the data integrity. Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 12/47 ESMT The system can determine the status of the erase operation by using DQ7, DQ6, DQ2, or RY/ BY . See “Write Operation Status” section for more information on these status bits. When the Embedded Erase algorithm is complete, the device returns to reading array data and addresses are no longer latched. See the Erase/Program Operations tables in “AC Characteristics” for parameters. F49L800UA/F49L800BA Once the sector erase operation has begun, only the Erase Suspend command is valid. All other commands are ignored. Note that a hardware reset during the sector erase operation immediately terminates the operation. The Sector Erase command sequence should be reinitiated once the device has returned to reading array data, to ensure the data integrity. When the Embedded Erase algorithm is complete, the device returns to reading array data and addresses are no longer latched. The system can determine the status of the erase operation by using DQ7, DQ6, DQ2, or RY/ BY . (Refer to “Write Operation Status” section for more information on these status bits.) Refer to the Erase/Program Operations tables in the “AC Characteristics” section for parameters. Sector Erase Command Sector erase is a six-bus cycle operation. The sector erase command sequence is initiated by writing two unlock cycles, followed by a set-up command. Two additional unlock write cycles are then followed by the address of the sector to be erased, and the sector erase command. The device does not require the system to preprogram the memory prior to erase. The Embedded Erase algorithm automatically programs and verifies the sector for an all zero data pattern prior to electrical erase. The system is not required to provide any controls or timings during these operations. After the command sequence is written, a sector erase time-out of 50 µs begins. During the time-out period, additional sector addresses and sector erase commands may be written. Loading the sector erase buffer may be done in any sequence, and the number of sectors may be from one sector to all sectors. The time between these additional cycles must be less than 50 μs, otherwise the last address and command might not be accepted, and erasure may begin. It is recommended that processor interrupts be disabled during this time to ensure all commands are accepted. The interrupts can be re-enabled after the last Sector Erase command is written. If the time between additional sector erase commands can be assumed to be less than 50 µs, the system need not monitor DQ3. Any command other than Sector Erase or Erase Suspend during the time-out period resets the device to reading array data. The system must rewrite the command sequence and any additional sector addresses and commands. The system can monitor DQ3 to determine if the sector erase timer has timed out. (See the “DQ3: Sector Erase Timer” section.) The time-out begins from the rising edge of the final WE pulse in the command sequence. Sector Erase Suspend/Resume Command The Erase Suspend command allows the system to interrupt a sector erase operation and then read data from, or program data to, any sector not selected for erasure (The device “erase suspends” all sectors selected for erasure.). This command is valid only during the sector erase operation, including the 50 µs time-out period during the sector erase command sequence. The Erase Suspend command is ignored if written during the chip erase operation or Embedded Program algorithm. Addresses are “don’t-cares” when writing the Erase Suspend command as shown in Table 5. When the Erase Suspend command is written during a sector erase operation, the device requires a maximum of 20 µs to suspend the erase operation. However, when the Erase Suspend command is written during the sector erase time-out, the device immediately terminates the time-out period and suspends the erase operation. Reading at any address within erase-suspended sectors produces status data on DQ7–DQ0. The system can use DQ7, or DQ6 and DQ2 together, to determine if a sector is actively erasing or is erase-suspended. See “Write Operation Status” section for more information on these status bits. After an erase-suspended program operation is complete, the system can once again read array data within non-suspended sectors. The system can determine the status of the program operation using the DQ7 or DQ6 status bits, just as in the standard program operation. See “Write Operation Status” for more information. Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 13/47 ESMT The system may also write the auto-select command sequence when the device is in the Erase Suspend mode. The device allows reading auto-select codes even at addresses within erasing sectors, since the codes are not stored in the memory array. When the device exits the auto-select mode, the device reverts to the Erase Suspend mode, and is ready for another valid operation. The system must write the Erase Resume command (address bits are “don’t care” as shown in Table 5) to exit the erase suspend mode and continue the sector erase operation. Further writes of the Resume command are ignored. Another Erase Suspend command can be written after the device has resumed erasing. F49L800UA/F49L800BA Table 6 shows the address and data requirements. This method is an alternative to that shown in Table 4, which is intended for PROM programmers and requires VID on address bit A9. The auto-select command sequence is initiated by writing two unlock cycles, followed by the auto-select command. The device then enters the auto-select mode, and the system may read at any address any number of times, without initiating another command sequence. The read cycles at address 04H, 08H, 0CH, and 00H retrieves the ESMT manufacturer ID. A read cycle at address 01H retrieves the device ID. A read cycle containing a sector address (SA) and the address 02H returns 01H if that sector is protected, or 00H if it is unprotected. Refer to Tables 1 and 2 for valid sector addresses. The system must write the reset command to exit the auto-select mode and return to reading array data. Auto-select Command The auto-select command sequence allows the host system to access the manufacturer and devices codes, and determine whether or not a sector is protected. 7.3 Write Operation Status The device provides several bits to determine the status of a write operation: RY/ BY , DQ7, DQ6, DQ5, DQ3, DQ2, and. Table 7 and the following subsections describe the functions of these bits. RY/ BY , DQ7, and DQ6 each offer a method for determining whether a program or erase operation is complete or in progress. Table 7. Write Operation Status Status Embedded Program Algorithm Embedded Erase Algorithm In Progress Reading Erase Suspended Sector Erase Suspended Mode Reading Non-Erase Suspended Sector Erase Suspend Program Embedded Program Algorithm Exceeded Time Limits Notes: 1. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details. 2. DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation has exceeded the maximum timing limits. See “DQ5: Exceeded Timing Limits” for more information. Embedded Erase Algorithm Erase Suspend Program DQ7 (Note1) DQ7 DQ6 Toggle Toggle No Toggle Data Toggle Toggle Toggle Toggle DQ5 DQ3 (Note2) 0 0 0 Data 0 1 1 1 N/A 1 N/A Data N/A N/A 1 N/A DQ2 No Toggle Toggle Toggle Data N/A No Toggle Toggle N/A RY/ BY 0 0 1 1 0 0 0 0 0 1 Data DQ7 DQ7 0 DQ7 Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 14/47 ESMT RY/ BY : Ready/Busy The RY/ BY is a dedicated, open-drain output pin that indicates whether an Embedded Algorithm is in progress or complete. The RY/ BY status is valid after the rising edge of the final WE pulse in the command sequence. Since RY/ BY is an open-drain output, several RY/ BY pins can be tied together in parallel with a pull-up resistor to VCC. If the output is low (Busy), the device is actively erasing or programming. (This includes programming in the Erase Suspend mode.) If the output is high (Ready), the device is ready to read array data (including during the Erase Suspend mode), or is in the standby mode. Table 7 shows the outputs for RY/ BY . F49L800UA/F49L800BA Output Enable ( OE ) is asserted low. Refer to Figure 21, Data Polling Timings (During Embedded Algorithms), Figure 19 shows the Data Polling algorithm. DQ6:Toggle BIT I Toggle Bit I on DQ6 indicates whether an Embedded Program or Erase algorithm is in progress or complete, or whether the device has entered the Erase Suspend mode. Toggle Bit I may be read at any address, and is valid after the rising edge of the final WE pulse in the command sequence (prior to the program or erase operation), and during the sector erase time-out. During an Embedded Program or Erase algorithm operation, successive read cycles to any address cause DQ6 to toggle. The system may use either OE or CE to control the read cycles. When the operation is complete, DQ6 stops toggling. When an erase command sequence is written, if all sectors selected for erasing are protected, DQ6 toggles for approximately 100 µs, then returns to reading array data. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. The system can use DQ6 and DQ2 together to determine whether a sector is actively erasing or is erase-suspended. When the device is actively erasing (i.e. the Embedded Erase algorithm is in progress), DQ6 toggles. When the device enters the Erase Suspend mode, DQ6 stops toggling. However, the system must also use DQ2 to determine which sectors are erasing or erase-suspended. Alternatively, the system can use DQ7. If a program address falls within a protected sector, DQ6 toggles for approximately 2 µs after the program command sequence is written, then returns to reading array data. DQ6 also toggles during the erase-suspend-program mode, and stops toggling once the Embedded Program algorithm is complete. Table 7 shows the outputs for Toggle Bit I on DQ6. Figure 20 shows the toggle bit algorithm. Figure 22 shows the toggle bit timing diagrams. Figure 25 shows the differences between DQ2 and DQ6 in graphical form. Refer to the subsection on DQ2: Toggle Bit II. DQ7: Data Polling The DQ7 indicates to the host system whether an Embedded Algorithm is in progress or completed, or whether the device is in Erase Suspend mode. The Data Polling is valid after the rising edge of the final WE pulse in the program or erase command sequence. During the Embedded Program algorithm, the device outputs on DQ7 the complement of the datum programmed to DQ7. This DQ7 status also applies to programming during Erase Suspend. When the Embedded Program algorithm is complete, the device outputs the true data on DQ7. The system must provide the program address to read valid status information on DQ7. If a program address falls within a protected sector, Data Polling on DQ7 is active for approximately 1 µs, then the device returns to reading array data. During the Embedded Erase algorithm, Data Polling produces a “0” on DQ7. When the Embedded Erase algorithm is complete, or if the device enters the Erase Suspend mode, Data Polling produces a “1” on DQ7. The system must provide an address within any of the sectors selected for erasure to read valid status information on DQ7. After an erase command sequence is written, if all sectors selected for erasing are protected, Data Polling on DQ7 is active for approximately 100 µs, then the device returns to reading array data. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. When the system detects DQ7 has changed from the complement to true data, it can read valid data at DQ7~ DQ0 on the following read cycles. This is because DQ7 may change asynchronously with DQ0–DQ6 while DQ2: Toggle Bit II The “Toggle Bit II” on DQ2, when used with DQ6, indicates whether a particular sector is actively erasing (that is, the Embedded Erase algorithm is in progress), or whether that sector is erase-suspended. Toggle Bit II is valid after the rising edge of the final WE or CE , whichever happens first, in the command sequence. Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 15/47 ESMT DQ2 toggles when the system reads at addresses within those sectors that have been selected for erasure. (The system may use either OE or CE to control the read cycles.) But DQ2 cannot distinguish whether the sector is actively erasing or is erase-suspended. DQ6, by comparison, indicates whether the device is actively erasing, or whether is in erase-suspended, but cannot distinguish which sectors are selected for erasure. Thus, both status bits are required for sector and mode information. Refer to Table 7 to compare outputs for DQ2 and DQ6. Figure 20 shows the toggle bit algorithm in flowchart form. See also the DQ6: Toggle Bit I subsection. Figure 22 shows the toggle bit timing diagram. Figure 25 shows the differences between DQ2 and DQ6 in graphical form. F49L800UA/F49L800BA exceeded the specified limits(internal pulse count). Under these conditions DQ5 will produce a "1". This time-out condition indicates that the program or erase cycle was not successfully completed. Data Polling and Toggle Bit are the only operating functions of the device under this condition. If this time-out condition occurs during sector erase operation, it specifies that a particular sector is bad and it may not be reused. However, other sectors are still functional and may be used for the program or erase operation. The device must be reset to use other sectors. Write the Reset command sequence to the device, and then execute program or erase command sequence. This allows the system to continue to use the other active sectors in the device. If this time-out condition occurs during the chip erase operation, it specifies that the entire chip is bad or combination of sectors are bad. If this time-out condition occurs during the programming operation, it specifies that the sector containing that byte is bad and this sector may not be reused, however other sectors are still functional and can be reused. The time-out condition will not appear if a user tries to program a non blank location without erasing. Please note that this is not a device failure condition since the device was incorrectly used. Reading Toggle Bits DQ6/ DQ2 Refer to Figure 20 for the following discussion. Whenever the system initially begins reading toggle bit status, it must read DQ7–DQ0 at least twice in a row to determine whether a toggle bit is toggling. Typically, the system would note and store the value of the toggle bit after the first read. After the second read, the system would compare the new value of the toggle bit with the first. If the toggle bit is not toggling, the device has completed the program or erase operation. The system can read array data on DQ7–DQ0 on the following read cycle. However, if after the initial two read cycles, the system determines that the toggle bit is still toggling, the system should note whether the value of DQ5 is high (see the section on DQ5). If it is, the system should then determine again whether the toggle bit is toggling, since the toggle bit may have stopped toggling just as DQ5 went high. If the toggle bit is no longer toggling, the device has successfully completed the program or erase operation. If it is still toggling, the device did not completed the operation successfully, and the system must write the reset command to return to reading array data. The remaining scenario is that the system initially determines that the toggle bit is toggling and DQ5 has not gone high. The system may continue to monitor the toggle bit and DQ5 through successive read cycles, determining the status as described earlier. Alternatively, it may choose to perform other system tasks. In this case, the system must start at the beginning of the algorithm when it returns to determine the status of the operation. DQ3:Sector Erase Timer After writing a sector erase command sequence, the system may read DQ3 to determine whether or not an erase operation has begun. (The sector erase timer does not apply to the chip erase command.) If additional sectors are selected for erasure, the entire timeout also applies after each additional sector erase command. When the time-out is complete, DQ3 switches from “0” to “1.” If the time between additional sector erase commands from the system can be assumed to be less than 50 µs, the system need not monitor DQ3. When the sector erase command sequence is written, the system should read the status on DQ7 (Data Polling) or DQ6 (Toggle Bit I) to ensure the device has accepted the command sequence, and then read DQ3. If DQ3 is “1”, the internally controlled erase cycle has begun; all further commands (except Erase Suspend) are ignored until the erase operation is complete. If DQ3 is “0”, the device will accept additional sector erase commands. To ensure the command has been accepted, the system software should check the status of DQ3 prior to and following each subsequent sector erase command. If DQ3 is high on the second status check, the last command might not have been accepted. Table 7 shows the outputs for DQ3. DQ5: Exceeded Timing Limits DQ5 indicates whether the program or erase time has Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 16/47 ESMT 7.4 More Device Operations Hardware Data Protection The command sequence requirement of unlock cycles for programming or erasing provides data protection against inadvertent writes. In addition, the following hardware data protection measures prevent accidental erasure or programming, which might otherwise be caused by spurious system level signals during VCC power-up and power-down transitions, or from system noise. F49L800UA/F49L800BA Logical Inhibit Write cycles are inhibited by holding any one of OE = VIL, CE = VIH or WE = VIH. To initiate a write cycle, CE and WE must be a logical zero while OE is a logical one. Power Supply Decoupling In order to reduce power switching effect, each device should have a 0.1uF ceramic capacitor connected between its VCC and GND. Low VCC Write Inhibit When VCC is less than VLKO, the device does not accept any write cycles. This protects data during VCC power-up and power-down. The command register and all internal program/erase circuits are disabled, and the device resets. Subsequent writes are ignored until VCC is greater than VLKO. The system must provide the proper signals to the control pins to prevent unintentional writes when VCC is greater than VLKO. Power-Up Sequence The device powers up in the Read Mode. In addition, the memory contents may only be altered after successful completion of the predefined command sequences. Write Pulse "Glitch" Protection Noise pulses of less than 5 ns (typical) on CE or WE do not initiate a write cycle. Power-Up Write Inhibit If WE = CE = VIL and OE = VIH during power up, the device does not accept commands on the rising edge of WE . The internal state machine is automatically reset to reading array data on power-up. Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 17/47 ESMT 8. ABSOLUTE MAXIMUM RATINGS Storage Temperature Plastic Packages . . . . . . . . . . . . . . –65°C to +150°C Ambient Temperature with Power Applied. . . . . . . .. . . . . . –65°C to +125°C Voltage with Respect to Ground VCC (Note 1) . . . . . . . . . . .–0.5 V to +4.0 V A9, OE , and RESET (Note 2) …. . . .. . . . . –0.5 V to +10.5 V All other pins (Note 1). . . . . . . . . . –0.5 V to VCC +0.5 V Output Short Circuit Current (Note 3) .. . .. 200 mA Notes: 1. Minimum DC voltage on input or I/O pins is –0.5 V. During voltage transitions, input or I/O pins may overshoot VSS to –2.0 V for periods of up to 20 ns. See Figure 1. Maximum DC voltage on input or I/O pins is VCC +0.5 V. During voltage transitions, input or I/O pins may overshoot to VCC +2.0 V for periods up to 20 ns. See Figure 2. F49L800UA/F49L800BA 2. Minimum DC input voltage on pins A9, OE , and RESET is -0.5 V. During voltage transitions, A9, OE , and RESET may overshoot VSS to –2.0 V for periods of up to 20 ns. See Figure 1. Maximum DC input voltage on pin A9 is +10.5 V which may overshoot to 14.0 V for periods up to 20 ns. 3. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second. Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability. Figure 1. Maximum Negative Overshoot Waveform 20 n s +0.8V -0.5V -2.0V 20 n s 20 n s Figure 2. Maximum Positive Overshoot Waveform 20 n s Vc c +2.0V Vc c +0.5V 2.0V 20 n s 20 n s Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 18/47 ESMT OPERATING RANGES F49L800UA/F49L800BA Commercial (C) Devices Ambient Temperature (TA) . . . . . . . . . . . 0°C to +70°C VCC Supply Voltages VCC for all devices . . . . . . . . . . . . . . . . . . . . .2.7 V to 3.6 V Operating ranges define those limits between which the functionality of the device is guaranteed. Table 8. Capacitance TA = 25°C , f = 1.0 MHz Symbol CIN1 CIN2 COUT Description Input Capacitance Control Pin Capacitance Output Capacitance Conditions VIN = 0V VIN = 0V VOUT = 0V Min. Typ. Max. 8 12 12 Unit pF pF pF 9. DC CHARACTERISTICS Table 9. DC Characteristics TA = 0C to 70C, VCC = 2.7V to 3.6V Symbol ILI ILIT ILO Description Input Leakage Current A9 Input Leakage Current Output Leakage Current Conditions VIN = VSS or VCC, VCC = VCC max. VCC = VCC max; A9=10.5V VOUT = VSS or VCC, VCC = VCC max CE = VIL, OE = VIH ( Byte Mode ) CE = VIL, OE = VIH ( Word Mode ) Min. Typ. Max. ±1 35 ±1 Unit uA uA uA mA mA mA mA mA uA uA uA V V V V @5MHz @1MHz @5MHz @1MHz 9 2 9 2 20 25 25 25 -0.5 0.7x VCC 25 5 40 5 50 100 100 100 0.8 VCC + 0.3 10.5 0.45 ICC1 VCC Active Read Current ICC2 ICC3 ICC4 ICC5 VIL VIH VID VOL VOH1 VOH2 VLKO Notes : VCC Active write Current VCC Standby Current VCC Standby Current During Reset Automatic sleep mode Input Low Voltage(Note 1) Input High Voltage Voltage for Auto-Select and Temporary Sector Unprotect Output Low Voltage Output High Voltage(TTL) Output High Voltage Low VCC Lock-out Voltage CE = VIL, OE = VIH CE ; RESET = VCC ± 0.3V RESET = VSS ± 0.3V VIH = VCC ± 0.3V; VIL = VSS ± 0.3V VCC =3.3V IOL = 4.0mA, VCC = VCC min IOH = -2mA, VCC = VCC min IOH = -100uA, VCC min 10 0.7x VCC VCC -0.4 2.3 2.5 V 1. VIL min. = -1.0V for pulse width is equal to or less than 50 ns. VIL min. = -2.0V for pulse width is equal to or less than 20 ns. 2. VIH max. = VCC + 1.5V for pulse width is equal to or less than 20 ns If VIH is over the specified maximum value, read operation cannot be guaranteed. 3. Automatic sleep mode enable the low power mode when addresses remain stable for 250 ns Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 19/47 ESMT 10. AC CHARACTERISTICS TEST CONDITIONS F49L800UA/F49L800BA Figure 3. Test Setup 2.7K DEVICE UNDER TEST +3.3V CL 6 .2 K DIODES = IN3064 O R EQ U I V A L E N T C L = 1 0 0 p F I n c lu d i n g ji g c a p a c it a n c e C L = 3 0 p F f o r F4 9 L 8 0 0 U/ BA Figure 4. Input Waveforms and Measurement Levels 3.0V 0V 1.5V In p u t Test Poin t s Out pu t 1.5V A C TE S TIN G : In p u t s a r e d ri v e n a t 3 . 0 V f o r a l o g i c " 1 " a n d 0 V f o r a l o g i c " 0 " In p u t p u l s e r i s e a n d f a l l t i m e s a r e < 5 n s . Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 20/47 ESMT 10.1 Read Operation TA = 0C to 70C, VCC = 2.7V~3.6V F49L800UA/F49L800BA Table 10. Read Operations Symbol tRC tACC tCE tOE tDF Description Read Cycle Time (Note 1) Address to Output Delay CE to Output Delay CE = OE = VIL Conditions -70 Min. 70 Max. 70 70 30 25 0 10 0 10 0 Min. 90 -90 Max. 90 90 35 30 Unit ns ns ns ns ns ns ns ns OE = VIL CE = VIL CE = VIL OE to Output Delay OE High to Output Float (Note1) Output Enable Read Toggle and Data Polling tOEH tOH Hold Time Address to Output hold CE = OE = VIL 0 Notes : 1. Not 100% tested. 2. tDF is defined as the time at which the output achieves the open circuit condition and data is no longer driven. Figure 5. Read Timing Waveform tRC Addr es s Addresses Stabl e tAC C CE tOE OE tOEH WE tCE tOH Ou t pu t s High-Z tDF High-Z Output Vali d RESET RY/BY 0V Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 21/47 ESMT 10.2 Program/Erase Operation F49L800UA/F49L800BA Table 11. WE Controlled Program/Erase Operations(TA = 0C to 70C, VCC = 2.7V~3.6V) Symbol tWC tAS tAH tDS tDH tOES tGHWL tCS tCH tWP tWPH tWHWH1 tWHWH2 tVCS tRB tbusy Description Write Cycle Time (Note 1) Address Setup Time Address Hold Time Data Setup Time Data Hold Time Output Enable Setup Time Read Recovery Time Before Write ( OE High to WE low) CE Setup Time CE Hold Time -70 Min. 70 0 45 35 0 0 0 0 0 35 30 9(typ.) 0.7(typ.) 50 0 90 Max. -90 Min. 90 0 45 35 0 0 0 0 0 35 30 9(typ.) 0.7(typ.) 50 0 90 Max. Unit ns ns ns ns ns ns ns ns ns ns ns us sec us ns ns Write Pulse Width Write Pulse Width High Programming Operation (Note 2) (Byte program time) Sector Erase Operation (Note 2) VCC Setup Time (Note 1) Recovery Time from RY/ BY Program/Erase Valid to RY/ BY Delay Notes : 1. Not 100% tested. 2. See the "Erase and Programming Performance" section for more information. Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 22/47 ESMT Symbol tWC tAS tAH tDS tDH tOES tGHEL tWS tWH tCP tCPH tWHWH1 tWHWH2 Notes : Description Write Cycle Time (Note 1) Address Setup Time Address Hold Time Data Setup Time Data Hold Time Output Enable Setup Time Read Recovery Time Before Write WE Setup Time WE Hold Time CE Pulse Width CE Pulse Width High F49L800UA/F49L800BA Table 12. CE Controlled Program/Erase Operations(TA = 0C to 70C, VCC =2.7V~3.6V) -70 Min. 70 0 45 35 0 0 0 0 0 35 30 9(typ.) 0.7(typ.) Max. -90 Min. 90 0 45 35 0 0 0 0 0 35 30 9(typ.) 0.7(typ.) Max. Unit ns ns ns ns ns ns ns ns ns ns ns us sec Programming Operation(note2) Sector Erase Operation (note2) 1. Not 100% tested. 2. See the "Erase and Programming Performance" section for more information. Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 23/47 ESMT VCC 3V F49L800UA/F49L800BA Figure 6. Write Command Timing Waveform Addr es s VIH VIL tAS VIH ADD Valid tAH WE VIL tOES tWP tCW C tWPH CE VIH VIL tCS tCH VIH VIL tDS tDH DIN OE Dat a VIH VIL Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 24/47 ESMT F49L800UA/F49L800BA Figure 7. Embedded Programming Timing Waveform Pr ogr am C omm an d S equ en ce ( l as t t wo cycl e) Read Stat us D at a ( last t w o cycl e) tWC Addr es s 5 55 h tAS PA tAH PA PA CE tGHWL tCH OE tW HW H1 tWP WE tCS tDS tDH A0 h PD tB US Y tWPH Dat a St at u s DOUT tRB RY/BY tVCS VCC Notes : 1. PA = Program Address, PD = Program Data, DOUT is the true data the program address. Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 25/47 ESMT F49L800UA/F49L800BA Figure 8. Embedded Programming Algorithm Flowchart S tart W rite Data AAH Address 555H W rite Data 55H Address 2AAH W rite Data A0H Address 555H In c r e m e n t address W rite Program Data/Address Data Poll from system No Verify W ork OK? Ye s No Last address? Ye s Embedded Program Completed Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 26/47 ESMT 555 for prog ram PA f or p rog r am 2AA for erase SA for sector erase 555 for ch ip eras e F49L800UA/F49L800BA Figure 9. CE Controlled Program Timing Waveform Data Pol li n g PA Addr es s tWC tWH WE tG HEL tAS tAH OE tCP tWHWH1 CE tWS tDS tDH Dat a A0 f o r p r og r a m PD f o r p r o g r a m 30 f or sect or erase 55 for erase 10 f or ch ip erase or 2 tCPH tBUSY DQ7 DOUT tRH RESET RY/BY Notes : 1. PA = Program Address, PD = Program Data, DOUT = Data Out , DQ7 = complement of data written to device 2. Figure indicates the last two bus cycles of the command sequence.. Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 27/47 ESMT Er as e Com mand Sequ en ce( last t w o cycl e) F49L800UA/F49L800BA Figure 10. Embedded Chip Erase Timing Waveform Read Statu s Dat a tWC Addr es s 2AAh tAS 5 55 h tAH VA VA CE tCH tGHWL OE tWP WE tCS tDS tDH 5 5h 1 0h tBUSY tWPH tW HW H2 Dat a In Progress Complete tRB RY/BY tVCS VCC Notes : SA = Sector Address (for Sector Erase, VA = Valid Address for reading status data (see "Write Operation Status") Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 28/47 ESMT F49L800UA/F49L800BA Figure 11. Embedded Chip Erase Algorithm Flowchart S tart W rite Data AAH Address 555H W rite Data 55H Address 2AAH W rite Data 80H Address 555H W rite Data AAH Address 555H W rite Data 55H Address 2AAH W rite Data 10H Address 555H Data Poll from System No Data = FFh? Ye s Embedded Chip Erease Completed Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 29/47 ESMT F49L800UA/F49L800BA Figure 12. Embedded Sector Erase Timing Waveform Er as e Com mand Sequ en ce( last t w o cycl e) Read Statu s Dat a tWC Addr es s 2AAh tAS SA tAH VA VA CE tCH tGHWL OE tWP WE tCS tDS tDH 55 h 3 0h tBUSY tWPH tW HW H2 Dat a In Progress Complete tRB RY/BY tVCS VCC Notes : SA = Sector Address (for Sector Erase, VA = Valid Address for reading status data (see "Write Operation Status") Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 30/47 ESMT S tart F49L800UA/F49L800BA Figure 13. Embedded Sector Erase Algorithm Flowchart W rite Data AAH Address 5 55H W rite Data 55 H Address 2AAH W rite Data 80H Address 555H W rite Data AAH Add ress 555H W rit e Data 55H Address 2AAH W rite Data 3 0H Address SA Last Sector to Erase Yes Data Po ll fro m System No No Data = FFH? Embedde d Sector Ere ase Co mplete d Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 31/47 ESMT S tart F49L800UA/F49L800BA Figure 14. Erase Suspend/Erase Resume Flowchart W rite Data B0H ERASE SUSPEND Tog gle Bi t c h ec kin g Q 6 not toggled No Ye s Read Array or Program Readi ng or Pr og r am m in g En d No Ye s W rite Data 30H ERASE RESUME Continue Erase An oth er Er ase Suspend? No Ye s Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 32/47 ESMT F49L800UA/F49L800BA Figure 15. In-System Sector Protect/Unprotect Timing Waveform ( RESET Control) VID VIH RESET SA,A 6 A1,A0 Valid* Sec t or P r ot ec t Sec tor U npr ot ec t Valid* Ver if y 4 0h Sector Protect = 150us Sec t or Un p r ot ect = 15m s Vali d* Dat a 1us 60 h 6 0h St at u s CE WE OE Notes : When sector protect, A6=0, A1=1, A0=0. When sector unprotect, A6=1, A1=1, A0=0. Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 33/47 ESMT S tart F49L800UA/F49L800BA Figure 16. In-System Sector Protect/Unprotect Algorithm ( RESET = VID) Start PLSCNT = 1 Protect all sector : The indicated portion of the sector protect algorithm must be performed for all unprotected sectors prior to issuing the first sector unprotect address PLSCNT = 1 RESET = V I D RESET = V I D W ait 1μ s? W ait 1μ s? T emporary Sector Unprotect Mode No First W rite Cyc le = 6 0 h ? First W rite Cyc le = 6 0 h ? No Temporary Sector Unprotect Mode Ye s Set up sector address No Ye s Al l s ec t o r s pr otected ? Sector Protect : W rite 60h to sector address with A6 = 0, A1 = 1, A0 = 0 Ye s Set up first sector address W ait 150 μ s? Sector Unprotect : W rite 60h to sector address with A6 = 1, A1 = 1, A0 = 0 Reset PLSCNT = 1 In c r e m e n t PL SC NT Verify Sector Protect : W rite 40h to sector address with A6 = 0, A1 = 1, A0 = 0 W ait 15 ms? Read from sector address with A6 = 0, A1 = 1, A0 = 0 No P LSCNT = 25? No Data = 01h? Ye s Protect another s e c to r ? No Remove V I D from RESET Ye s In c r e m e n t PL SC NT Verify Sector Unprotect : W rite 40h to sector address with A6 = 1, A1 = 1, A0 =0 Ye s Dev ice failed Read from sector address with A6 = 1, A1 = 1, A0 =0 No PLSCNT = 1000? Ye s Dev ice failed No Data = 00h? Set up next sector address Ye s Last sector v erified ? Ye s No W rite reset command Sector Protect Algorithm Sector Protect c o m p le te Sector Unprotect Algorithm Remove V I D from RESET W rite reset command Sector Protect c o m p le te Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 34/47 ESMT F49L800UA/F49L800BA Figure 17. Sector Protect Timing Waveform (A9, OE Control) Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 35/47 ESMT F49L800UA/F49L800BA Figure 18. Sector Protection Algorithm (A9, OE Control) S tart Set up sector address PLSCNT = 1 OE = V ID , A9 = V ID , CE = V I L A6 = V IL Activ ate W E Pluse Time out 150us Set W E = V I H , C E = OE = V I L A9 should remain V I D No No PLSCNT = 32? Ye s Dev ice Failed Read from Sector Address = SA, A0=1, A1 = 1 Data = 01H? Protect Another Sector? Ye s Remov e VID from A9 W rite reset command Sector Protection C o m p l e te Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 36/47 ESMT F49L800UA/F49L800BA WRITE OPERATION STATUS Figure 19. Data Polling Algorithm S tart Read DQ7~DQ0 Add. = VA(1) DQ7 = Data? Ye s No No D Q5 = 1? Ye s Read DQ7~DQ0 Add. = VA DQ7 = Data? Ye s (2 ) No FAIL Pass Notes : 1. VA =Valid address for programming. 2. DQ7 should be re-checked even DQ5 = "1" because DQ7 may change simultaneously with DQ5. Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 37/47 ESMT S tart F49L800UA/F49L800BA Figure 20. Toggle Bit Algorithm Read DQ7 ~ DQ0 Read DQ7 ~ DQ0 (Note 1) Toggle Bit = DQ6 Toggle? No Ye s No D Q 5 = 1? Ye s Re ad D Q7 ~D Q 0 Tw ice (Note 1,2) Toggle bit D Q6 = Tog gle? No Ye s Program / Erase operation Not complete, write reset command Program / Erase operation complete Note : 1. Read toggle bit twice to determine whether or not it is toggle. 2. Recheck toggle bit because it may stop toggling as DQ5 change to "1". Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 38/47 ESMT tRC Addr es s tAC C tCE CE tCH tOE OE tOEH tDF VA F49L800UA/F49L800BA Figure 21. Data Polling Timings (During Embedded Algorithms) VA WE tO H High-Z DQ7 Complement Complement Tr u e Vai l d Dat a High-Z DQ0~DQ6 tB US Y Statu s Data Statu s Data Tr u e Vai l d Dat a RY/BY Notes : VA = Valid Address. Figure shows first status cycle after command sequence, last status read cycle, and array data read cycle. Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 39/47 ESMT tRC Addr es s VA tAC C tCE CE tCH tOE OE tOEH tDF VA F49L800UA/F49L800BA Figure 22. Toggle Bit Timing Waveforms (During Embedded Algorithms) VA VA WE tOH DQ6/DQ2 High-Z tBUSY Vaild Status Vaild Status Vaild Data (stops tog gling ) Vaild Data (fi rst re ad ) (sec ond read ) RY/BY Notes : VA = Valid Address; not required for DQ6. Figure shows first status cycle after command sequence, last status read cycle, and array data read cycle. Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 40/47 ESMT 10.3 Hardware Reset Operation F49L800UA/F49L800BA Table 13. AC CHARACTERISTICS Symbol TREADY1 TREADY2 TRP TRH TRB Description RESET Pin Low (During Embedded Algorithms) to Read or Write (See Note) RESET Pin Low (NOT During Embedded Algorithms) to Read or Write (See Note) RESET Pulse Width (During Embedded Algorithms) RESET High Time Before Read(See Note) All Speed Options Max Max Min Min Min 20 500 500 50 0 Unit us ns ns ns ns RY/ BY Recovery Time(to CE , OE go low) Notes : Not 100% tested Figure 23. RESET Timing Waveform RY/BY CE, O E tRH RESET tRP tRead y2 Reset T i mi ng NO T dur i ng Au tom at i c Al gor i th m s tRead y1 RY/BY tRB CE, O E RESET tRP Reset Tim ing during Automatic Algorithm s Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 41/47 ESMT 10.4 TEMPORARY SECTOR UNPROTECT Operation Symbol TVIDR TRSP Notes: Not 100% tested Description VID Rise and Fall Time (See Note) RESET Setup Unprotect F49L800UA/F49L800BA Table 14. Temporary Sector Unprotect All Speed Options Min Sector Min 500 4 Unit ns us Time for Temporary Figure 24. Temporary Sector Unprotect Timing Diagram 10V RE SE T 0 or VC C t V I DR CE Pr ogr am or Er as e C om ma nd Se quen c e 0 or V C C tV IDR WE t RS P RY/BY Figure 25. DQ6 vs DQ2 for Erase and Erase Suspend Operations En ter E m bedde d Er as in g WE Er as e S u s pe n d Enter Eras e Suspend Program Er as e Su s pen d Pr ogr am Er as e Resume Er as e Su s pen d Read Er as e Er as e Com pl et e DQ6 DQ2 Notes : The system can use OE or CE to toggle DQ2 / DQ6, DQ2 toggles only when read at an address within an erase-suspended. Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 42/47 ESMT S tart F49L800UA/F49L800BA Figure 26. Temporary Sector Unprotect Algorithm RESET = V ID ( Note 1) P rogram Erase or Program Operation Operation Completed RESET = V I H Temporary Sector Unprotect Completed (Note 2) Notes : 1. All protected status are temporary unprotect. VID = 10V~10.5V 2. All previously protected sectors are protected again. Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 43/47 ESMT F49L800UA/F49L800BA Figure 27. ID Code Read Timing Waveform Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 44/47 ESMT 11. ERASE AND PROGRAMMING PERFORMANCE F49L800UA/F49L800BA Table 15. Erase And Programming Performance (Note.1) Parameter Sector Erase Time Chip Erase Time Byte Programming Time Word Programming Time Chip Programming Time Erase/Program Cycles (1) Data Retention Notes: 1.Not 100% Tested, Excludes external system level over head. 2.Typical values measured at 25°C, 3.3V. 3.Maximum values measured at 85°C, 2.7V. Byte Mode Word Mode Limits Typ.(2) 0.7 14 9 11 9 5.8 100,000 20 300 360 27 17 Max.(3) 15 Unit Sec Sec Us Us Sec Sec Cycles Years Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 45/47 ESMT 12. PACKAGE DIMENSION 48-LEAD TSOP(I) ( 12x20 mm ) F49L800UA/F49L800BA Symbol A A1 A2 b b1 c c1 Dimension in mm Min Norm Max ------- ------- 1.20 0.05 ------- 0.15 0.95 1.00 1.05 0.17 0.22 0.27 0.17 0.10 0.10 0.20 ------------0.23 0.21 0.16 Dimension in inch Dimension in mm Symbol Min Norm Max Min Norm Max D ------- ------- 0.047 20.00 BSC 0.006 ------- 0.002 D1 18.40 BSC 0.037 0.039 0.041 E 12.00 BSC 0.007 0.009 0.011 0.50 BSC e L 0.007 0.008 0.009 0.50 0.60 0.70 0.004 0.004 ------------0.008 0.006 θ 0 O Dimension in inch Min Norm Max 0.787 BSC 0.724 BSC 0.472 BSC 0.020 BSC 0.020 0O 0.024 ------0.028 8O ------- 8 O Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 46/47 ESMT All rights reserved. F49L800UA/F49L800BA Important Notice No part of this document may be reproduced or duplicated in any form or by any means without the prior permission of ESMT. The contents contained in this document are believed to be accurate at the time of publication. ESMT assumes no responsibility for any error in this document, and reserves the right to change the products or specification in this document without notice. The information contained herein is presented only as a guide or examples for the application of our products. No responsibility is assumed by ESMT for any infringement of patents, copyrights, or other intellectual property rights of third parties which may result from its use. No license, either express , implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of ESMT or others. Any semiconductor devices may have inherently a certain rate of failure. To minimize risks associated with customer's application, adequate design and operating safeguards against injury, damage, or loss from such failure, should be provided by the customer when making application designs. ESMT 's products are not authorized for use in critical applications such as, but not limited to, life support devices or system, where failure or abnormal operation may directly affect human lives or cause physical injury or property damage. If products described here are to be used for such kinds of application, purchaser must do its own quality assurance testing appropriate to such applications. Elite Semiconductor Memory Technology Inc. Publication Date : Jan. 2008 Revision: 1.6 47/47