P2821

PRODUCT DATA SHEET POWERLINE CARRIER ISOLATION TRANSFORMERS P2820 P2821 P2822 P2823 Applications ∗ Powerline Carrier Features ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ Lead-free (Pb-free) RoHS compliant Reinforced insulation 14.6mm seated height Vacuum encapsulated Low distortion IEC 60950 and UL 60950 certified UL Recognized Component DESCRIPTION The family of transformers P2820, P2821, P2822 and P2823 is specifically designed to provide signal coupling with safety for Powerline Carrier applications over four bands from 40kHz to 148.5kHz. Typically, the devices are driven from lowimpedance sources and are connected to the mains network using capacitors whose values are chosen to resonate with the transformer leakage inductance. They are particularly suitable for use with tri-state power amplifiers, e.g. Texas Instruments TLE2301. The devices are completely lead-free, compliant with RoHS Directive 2002/95/EC, and suitable for lead-free and conventional processing. The devices are certified to IEC 60950 and UL 60950 for reinforced insulation. They are UL Recognized Components and are supported by an IEC CB Test Certificate. Furthermore, the devices are designed for low distortion and meet the requirements of EN 50065-1 for conducted emissions. ETALDOC 345/10 Page 1 of 6 March 2006 P2820, P2821, P2822, P2823 SPECIFICATIONS Distortion Exceed requirements of EN 50065-1 (1991) for conducted emissions Conditions: P2820, Fundamental 40-90kHz into artificial mains network of EN 50065-1 at 122dBµV and AC magnetizing current of 40mA rms at 50Hz. Circuit as Figure 1. P2822, Fundamental 125-140kHz into artificial mains network of EN 50065-1 at 116dBμV and AC magnetizing current of 3mA rms at 50Hz. Circuit as Figure 3. P2821, Fundamental 95-125kHz into artificial mains network of EN 50065-1 at 116dBμV and AC magnetizing current of 10mA rms at 50Hz. Circuit as Figure 2. P2823, Fundamental 140-148.5kHz into artificial mains network of EN 50065-1 at 116dBμV and AC magnetizing current of 3mA rms at 50Hz. Circuit as Figure 4. ETALDOC 345/10 Page 2 of 6 March 2006 P2820, P2821, P2822, P2823 Summary Specification Voltage Isolation 4kVrms at 50Hz Operating range Ambient Storage Relative Humidity -25 to +85ºC -40 to +125ºC to 95% Typical lumped parameters as Fig. 5 referred to pins 1-3. Parameter Series resistance RS (DCR+ AC resistance) Leakage inductance ΔL Shunt inductance LP Shunt loss RP Turns ratio, N Conditions 1V 100kHz 1V 100kHz 1V 100kHz 1V 100kHz 1V 100kHz P2820 0.5 14.4 400 >20 1.67 P2821 0.6 22 600 >20 3.22 P2822 1.0 46 1200 >20 3.15 P2823 1.3 58 1600 >20 3.00 Units Ω µH µH kΩ Equivalent Circuit F5 ig IDEAL 1:N ETALDOC 345/10 Page 3 of 6 March 2006 P2820, P2821, P2822, P2823 Detailed Specification, P2820 Electrical At T = 25ºC and as circuit fig. 5 unless otherwise indicated. Parameter Series resistance Conditions Refered to pins 1-3 40kHz 90kHz 40-90kHz 1-3; 5% drop in shunt inductance, Lp Coil to ambient Min 0.2 – 0.2 120 1.65 50Hz DC Ambient temperature -25 -40 +85 +125 ºC ºC 4.0 5.5 Typ 0.27 0.38 150 50 1.68 Max 0.7 0.7 70 1.71 Units Ω Ω Ω mA ºC/W kVrms kV Saturation Current Thermal resistance Turns ratio, N Voltage isolation (1) Operating range: Functional Storage Lumped equivalent circuit parameters as Fig. 6 DC resistance Leakage inductance ΔL Shunt inductance Lp Shunt loss Rp Interwinding capacitance, Ciw Notes: 1. Components are 100% tested at 6.5kVDC. 1,3 : 4,6 1-3, -25ºC to +85ºC 4-6, -25ºC to +85ºC -25ºC to +85ºC 25ºC -25ºC to +85ºC 0.08 0.20 13.9 300 175 10 0.2 0.54 15.9 700 1200 20 Ω Ω µH µH µH kΩ pF 14.9 500 8 Lumped Circuit parameters F6 ig IDEAL 1:1.68 ETALDOC 345/10 Page 4 of 6 March 2006 P2820, P2821, P2822, P2823 CONSTRUCTION e2 Dimensions shown are in millimetres (inches). Geometric centres of outline and pad grid coincide within a tolerance circle of 0.3mmØ. Windings may be used interchangeably a primary or secondary. SAFETY Constructed in accordance with IEC 60950-1:2001, EN 60950-1:2001 and UL 60950-1, first Edition, reinforced insulation 250Vrms maximum working voltage, flammability class V-0. Distance through solid insulation 0.4mm minimum. Creepage and clearances in circuit are 9mm minimum where PCB pads do not exceed Ø3mm. CERTIFICATION Certified under the IEC CB scheme (Certificate DK-9431) to IEC 60950-1:2001, sub-clauses 1.5, 1.5.1, 1.5.2, 1.7, 1.7.1, 2, 2.9, 2.9.1, 2.9.2, 2.9.3, 2.10, 2.10.1, 2.10.2, 2.10.3, 2.10.3.1, 2.10.3.3, 2.10.4, 2.10.5, 2.10.5.1, 2.10.5.4, 4, 4.7, 4.7.1, 4.7.3, 4.7.3.1, 4.7.3.4, 5, 5.2, 5.2.1, and 5.2.2 for a maximum working voltage of 250Vrms, nominal mains supply voltage not exceeding 250Vrms and a maximum operating temperature of 85ºC in Pollution Degree 2 environments, reinforced insulation, including national differences for Denmark, Finland, Germany, Norway, Sweden, Switzerland, USA, Canada and UK. Recognized under the Component Recognition Program of Underwriters Laboratories Inc. to US and Canadian requirements CAN/CSA C22.2 No. 60950-1-03/UL60950-1, First Edition, based on IEC 60950-1, First Edition, maximum working voltage 250Vrms, Pollution Degree 2, reinforced insulation. UL File number E203175. Additionally, Profec Technologies certifies all transformers as providing voltage isolation of 3.88kVrms, 5.5kV DC minimum. All shipments are supported by a certificate of conformity to current applicable safety standards. ETALDOC 345/10 Page 5 of 6 March 2006 P2820, P2821, P2822, P2823 ABSOLUTE MAXIMUM RATINGS (Ratings of components independent of circuit). Short term isolation voltage (1s) Coil temperature (continuous) Storage temperature Lead temperature, 10s 4.6kVrms, 6.5kVDC 155ºC -40ºC to +125ºC 260ºC COPYRIGHT ETAL, P2820, P2821, P2822, and P2823 are Trade Marks of Profec Technologies Ltd. The Trade Mark ETAL is registered at the UK Trade Marks Registry. Profec Technologies Ltd. is the owner of the design right under the Copyright Designs and Patents Act 1988 and no rights or licences are hereby granted or implied to any third party. © 1996 - 2006 Profec Technologies Ltd. Reproduction prohibited. E203175 ISO 9001 FM 25326 ETAL Group Oy, Kuormatie 14, FIN-03101, Nummela Telephone: +358 (0)20 7500 330 Fax: +358 (0)20 7500 333 Website: www.etalgroup.com Email: etalgroup@egruppen.com ETALDOC 345/10 Page 6 of 6 March 2006