P3065

PRODUCT DATA SHEET LOW PROFILE LINE MATCHING TRANSFORMER Features ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ Low Distortion Lead-free (Pb-free) RoHS compliant Low Profile (11mm) Vacuum encapsulated IEC 60950 and UL 60950 certified UL Recognized Component High Thermal Stability P3065 Applications ∗ ∗ ∗ ∗ ∗ ∗ V.34 modems Data rates to 33.6kbps Line matching Portable computers Fax/modems Instrumentation DESCRIPTION P3065 is intended for data communications to 33,600 bits/second data rates. P3065 is specifically designed to be easily matched to both 600 ohm and complex impedance telephone lines, using a minimum of external components. P3065 also exhibits stable characteristics over its operating temperature range to maximize data throughput under varying environmental conditions without the need for modem retraining. P3065 is certified to IEC 60950 and UL 60950. P3065 is a UL Recognized Component, and is supported by an IEC CB Test Certificate. The part is completely lead-free, compliant with RoHS Directive 2002/95/EC, and suitable for lead-free and conventional processing. ETALDOC 479/14 Page 1 of 5 February 2006 P3065 SPECIFICATIONS Electrical At T = 25ºC and as circuit Fig. 2 unless otherwise stated. Parameter Insertion Loss Frequency Response Conditions f = 2kHz, RL = 470Ω LF -3dB cutoff HF -3dB cutoff 200Hz - 4kHz 200Hz - 4kHz 0dBm in line, 3rd Harmonic f = 600Hz -10dBm in line, 3rd Harmonic f = 600Hz DC - 5kHz Excitation 50Hz 250Vrms. Output voltage across line 50Hz DC Ambient temperature -25 -40 +85 +125 95 ºC ºC %R.H. Min 16 80 Typ 2.5 30 15 -85 -100 Max 3.0 ±0.2 -80 -95 Units dB Hz kHz dB dB dBm dBm dB Return Loss Distortion (1) Balance Saturation 3.88 5.5 - 10 65 - Vrms Vpeak kVrms kV Voltage (2) isolation Operating range: Functional Storage Humidity Lumped equivalent circuit parameters as Fig. 1 DC resistance, RDC(3) Leakage inductance ΔL Shunt inductance Lp(4) Shunt loss Rp(4) 100mV 200Hz 100mV 1kHz 10mV 200Hz 10mV 1kHz Sum of windings 170 3.5 12 18 20 6 4 210 16 Ω mH H H kΩ kΩ Notes 1. Third harmonic typically exceeds other harmonics by 10dB. 2. Components are 100% tested at 6.5kV DC. 3. Caution: do not pass DC through windings. Telephone line current, etc. must be diverted using semiconductor line hold circuit. 4. At signal levels greater than 100mV, Lp will increase and Rp will decrease slightly but the effect is usually favourable to the return loss characteristic. Equivalent Circuit F1 ig IDE AL 1:1 LINE MODE M ETALDOC 479/14 Page 2 of 5 February 2006 P3065 PERFORMANCE CHARACTERISTICS 600Ω MATCH Recommended Circ uit F2 ig 600 4.7μF LINE 10nF 22nF 470 EUROPEAN CTR21 COMPLEX MATCH Recommended Circ uit F3 ig Recommended Circ uit F4 ig 150nF 270 2.2μ F 120nF 270 750 150nF 2.2μ F 750 47nF LINE 100 LINE 750 33nF 68nF 820 Figure 3 gives flat RX and TX responses against the reference impedance (typically around ±0.5dB 300Hz - 3.4kHz). Return loss is typically better than 20dB. The 120nF capacitor should be of a temperature stable dielectric. In practice, the 100ohm resistor will normally connect to a low impedance TX output. For circuits with existing board drillings, figure 4 gives good return loss (>20dB) against the reference impedance, but TX and RX flatness are degraded by the use of this topology. In practice, the 820ohm resistor will normally connect to a low impedance TX output. The 68nF capacitor, which should be of a temperature stable dielectric, should be placed in parallel with the 820ohm resistor (rather than in parallel with the transformer winding) to obtain good TX flatness. For recommended matching to other reference impedances please contact Profec Technologies. ETALDOC 479/14 Page 3 of 5 February 2006 P3065 CONSTRUCTION e2 Dimensions shown are in millimetres (inches). Geometric centres of outline and pin grid coincide within a tolerance circle of 0.6mmØ. Windings may be used interchangeably as primary or secondary. SAFETY Constructed in accordance with IEC 60950-1:2001, EN60950-1:2001, and UL 60950-1 First Edition, supplementary insulation, 250Vrms maximum working voltage, flammability class V-0. Distances through solid insulation 0.4mm minimum. CERTIFICATION Certified under the IEC CB scheme (Certificate DK-9431) to IEC 60950-1:2001, sub-clauses 1.5, 1.5.1, 1.5.2, 1.7, 1.7.1, 2, 2.9, 2.9.1, 2.9.2, 2.9.3, 2.10, 2.10.1, 2.10.2, 2.10.3, 2.10.3.1, 2.10.3.3, 2.10.4, 2.10.5, 2.10.5.1, 2.10.5.4, 4, 4.7, 4.7.1, 4.7.3, 4.7.3.1, 4.7.3.4, 5, 5.2, 5.2.1, and 5.2.2 for a maximum working voltage of 250Vrms, nominal mains supply voltage not exceeding 300Vrms and a maximum operating temperature of 85ºC in Pollution Degree 2 environments, supplementary insulation, including national differences for Denmark, Finland, Germany, Norway, Sweden, Switzerland, USA, Canada and UK. Recognized under the Component Recognition Program of Underwriters Laboratories Inc. to US and Canadian requirements CAN/CSA C22.2 No. 60950-1-03/UL60950-1, First Edition, based on IEC 60950-1, First Edition, maximum working voltage 250Vrms, Pollution Degree 2, reinforced insulation. UL File number E203175. Additionally, Profec Technologies certifies all transformers as providing voltage isolation of 3.88kVrms, 5.5kV DC minimum. All shipments are supported by a Certificate of Conformity to current applicable safety standards. ETALDOC 479/14 Page 4 of 5 February 2006 P3065 ABSOLUTE MAXIMUM RATINGS (Ratings of components independent of circuit). Short term isolation voltage (2s) DC current Storage temperature Lead temperature, 10s 4.6kVrms, 6.5kVDC 100μA -40ºC to +125ºC 260ºC COPYRIGHT ETAL and P3065 are Trade Marks of Profec Technologies Ltd. The Trade Mark ETAL is registered at the UK Trade Marks Registry. Profec Technologies Ltd. is the owner of the design right under the Copyright Designs and Patents Act 1988 and no rights or licences are hereby granted or implied to any third party. © 1997-2006 Profec Technologies Ltd. Reproduction prohibited. E203175 ISO 9001 FM 25326 ETAL Group Oy, Kuormatie 14, FIN-03101, Nummela Telephone: +358 (0)20 7500 330 Fax: +358 (0)20 7500 333 Website: www.etalgroup.com Email: etalgroup@egruppen.com ETALDOC 479/14 Page 5 of 5 February 2006