P3191

PRODUCT DATA SHEET MICROPROFILE SMD LINE MATCHING TRANSFORMER Features ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ Surface Mount Lead-free (Pb-free) RoHS compliant 7mm seated height Vacuum encapsulated IEC 60950 and UL 60950 certified UL Recognized Component Simple 600Ω match P3191 Applications ∗ ∗ ∗ ∗ Telecommunications V.34 modems Portable computers Fax/Modems DESCRIPTION P3191 is a low distortion microprofile transformer for applications where high performance and safety isolation to international standards are required in an extremely small case size. Designed specifically as a surface mount device, the P3191 features a 7mm seated height and is offered in the same package as the now familiar P2781. The part is compliant with RoHS Directive 2002/95/EC, and suitable for lead-free and conventional placement and reflow. Despite the subminiature size, the performance is superior to that of much larger components. The P3191 offers reinforced insulation, is ideal for data communications at high data rates, and can be matched to both 600Ω and complex impedance telephone lines. When used with 600Ω lines no external compensation components are required. At moderate transmit power levels (e.g. -10dBm) performance to 33,600 bits/second may be achieved. P3191 is certified to IEC 60950 and UL 60950. P3191 is a UL Recognized Component, and is supported an IEC CB Test Certificate. ETALDOC 590/10 Page 1 of 4 October 2007 P3191 SPECIFICATIONS Electrical At T = 25°C and as circuit Fig. 2 unless otherwise stated. Parameter Insertion Loss Frequency response Conditions f = 2kHz -3dB LF cutoff -3dB HF cutoff 200Hz - 4kHz 200Hz - 4kHz 600Hz -10dBm in line DC - 5kHz Method TG25 Excitation 50Hz 250Vrms. Output voltage across line 50Hz DC Ambient temperature -25 –40 +85 +125 95 °C °C %R.H. Min 16 80 Typ 50 35 -93 Max 4.5 ±0.2 Units dB Hz kHz dB dB dBm dB Return Loss Third Harmonic Distortion (1) Balance Saturation 3.88 5.5 - 10 65 - Vrms Vpeak kVrms kV Voltage isolation(2) Operating range: Functional Storage(5) Humidity Lumped equivalent circuit parameters as Fig. 1 DC resistance, RDC(3) Leakage inductance ΔL Shunt inductance Lp(4) Shunt loss Rp (4) Sum of windings 270 - 5.6 340 - Ω mH 10mv 200Hz 10mV 200Hz 2.4 7 - - H kΩ Notes 1. Third harmonic typically exceeds other harmonics by 20dB. 2. Components are 100% tested at 6.5 kVDC. 3. Caution: do not pass DC through windings. Telephone line current, etc. must be diverted using choke or semiconductor line hold circuit. 4. At signal levels greater than 100mV, Lp will increase and Rp will decrease slightly but the effect is usually favourable to the return loss characteristic. 5. Excludes shipping materials. Components are dry-packed and sealed as shipped. Handle in accordance with IPC/JEDEC J-STD-033 procedure for components classified as IPC/JEDEC J-STD-020 Moisture Sensitivity Level 5a. Equivalent Circuit Fig. 1 ½ L ½R ½R ½L IDEAL 1:1 ETALDOC 590/10 Page 2 of 4 October 2007 P3191 MATCHING RECOMMENDATIONS 600Ω MATCH Recommended Circ uit F2 ig 600 6.8μF EUROPEAN CTR21 COMPLEX MATCH Recommended Circ uit F3 ig 150nF 270 2.2μF LINE 430 750 15n LINE 100n 910 In practice, the 910Ω load resistor will connect to a low output impedance TX driver. The 100nF capacitor should appear in parallel with the 910Ω load resistor (rather than in parallel with transformer winding) to obtain optimum TX flatness to line. CONSTRUCTION Connections Fig 4 Dimensions F3 ig 2.54 2.54 (0.1) (0.1) e3 9.0 max (0.36) 7.0 max (0.28) 13.0 max (0.51) 1 2 3 6 5 4 1.77 (0.07) 1.32 (0.052) 1.5 (0.06) NOT : E Dimensions shown are in millimetres (inches) T olerance ± 0.3mm T erminals electroplated pure tin (S 5µm minimum. n) JES D97 c ategory = e3. T erminal size : 1.5 (0.06) long, 1.32 (0.05) wide Dimensions shown are in millimetres (inches). Geometric centres of outline and pad grid coincide within a tolerance circle of 0.3mm∅. Windings may be used interchangeably as primary or secondary. ETALDOC 590/10 Page 3 of 4 October 2007 P3191 SAFETY Manufactured from materials conforming to flammability requirements of UL94V-0. Distance through reinforced insulation 0.4mm minimum. Creepage and clearances in circuit are 7mm minimum where PCB pads do not exceed 3mmØ. Construction complies with IEC 60950-1, EN 60950-1 and UL 60950-1, reinforced insulation, 250Vrms maximum working voltage. CERTIFICATION Certified by BSI to IEC 60950 Third Edition (1999) (IEC CB Test Certificate No. GB592W) sub-clauses 1.5, 1.5.1, 1.5.2, 2.9, 2.9.1, 2.9.2, 2.9.3, 2.9.4, 2.9.5, 2.10, 2.10.1, 2.10.2, 2.10.3, 2.10.3.1, 2.10.3.2, 2.10.4, 2.10.5, 2.10.5.1, 2.10.7, 2.10.8, 4.7, 4.7.3, 4.7.3.1, 4.7.3.4, (Flammability Class V-0) ,5.2, 5.2.1, and 5.2.2 for a maximum working voltage of 250Vrms, nominal mains supply voltage not exceeding 250Vrms and a maximum operating temperature of +85°C in Pollution Degree 2 environment, reinforced insulation. Recognized under the Component Recognition Program of Underwriters Laboratories Inc. to US and Canadian requirements CAN/CSA C22.2 No. 60950-1-03/UL60950-1, First Edition, based on IEC 60950-1, First Edition, maximum working voltage 250Vrms, Pollution Degree 2, reinforced insulation. UL File number E203175. Additionally, Profec Technologies certifies all transformers as providing voltage isolation of 3.88kVrms, 5.5kV DC minimum. All shipments are supported by a Certificate of Conformity to current applicable safety standards. ABSOLUTE MAXIMUM RATINGS (Ratings of components independent of circuit). Short term isolation voltage (2s) DC current Storage temperature 4.6 kVrms, 6.5kVDC 100μA -40°C to +125°C Soldering temperature Profile peak 260°C 10s Recommended peak body temperature 245°C in accordance with IPC/JEDEC J-STD-033. ORDERING CODE P3191 TR = Tape and Reel (Blank) = Bulk in tubes. Carrier tape width 24mm, 500 parts per 13” reel. COPYRIGHT ETAL, P3191 and P2781 are Trade Marks of Profec Technologies Ltd. The Trade Mark ETAL is registered at the UK Trade Marks Registry. Profec Technologies Ltd. is the owner of the design right under the Copyright Designs and Patents Act 1988 and no rights or licences are hereby granted or implied to any third party. British Patent No. 2283195 US Patent No. 5879598 European Patent No. 0725719 © 1998 - 2005 Profec Technologies Ltd. Reproduction prohibited. E203175 ETAL Group Oy, Kuormatie 14, FIN-03101, Nummela Telephone: +358 (0)20 7500 330 Fax: +358 (0)20 7500 333 Website: www.etalgroup.com Email: etalgroup@egruppen.com ISO 9001 FM 25326 ETALDOC 590/10 Page 4 of 4 October 2007