AZ696-1C-24D

AZ696 10 AMP SUBMINIATURE POWER RELAY FEATURES • • • • • • • High sensitivity, 110 mW pickup Dielectric strength 4000 Vrms Isolation spacing greater than 8 mm Proof tracking index (PTI/CTI) 250 10 Amp switching capability Epoxy sealed version available Reinforced insulation, EN 60730-1 (VDE 0631, part 1) EN 60335-1 (VDE 0700, part 1) • UL, CUR file E44211, • VDE file 117422 ÜG CONTACTS Arrangement Ratings SPDT (1 Form C) SPST (1 Form A and 1 Form B) Resistive load: Max. switched power: 240 W or 2500 VA Max. switched current: 10 A Max. switched voltage: 240 VDC* or 440 VAC * Note: If switching voltage is greater than 30 VDC, GENERAL DATA Life Expectancy Mechanical Electrical Operate Time (typical) Release Time (typical) Minimum operations 1 X 107 1 X 105 at 8 A 250 VAC Res. 10 ms at nominal coil voltage 5 ms at nominal coil voltage (with no coil suppression) special precautions must be taken. Please contact the factory. Dielectric Strength 4000 Vrms coil to contact (at sea level for 1 min.) 1000 Vrms between open contacts Insulation Resistance Insulation (according to DIN VDE 0110, IEC 60664-1) Dropout Ambient Temperature Operating Storage Vibration 1000 megohms min. at 20°C, 500 VDC, 50% RH C250 Overvoltage category: III Pollution degree: 3 Nominal voltage: 250 VAC Greater than 10% of nominal coil voltage At nominal coil voltage -40°C (-40°F) to 85°C (185°F) -40°C (-40°F) to 105°C (221°F) 0.062" (1.5 mm) DA at 10–55 Hz 20 g P.B.T. polyester, UL94 V-0 Tinned copper alloy, P.C. 270°C (518°F) 5 seconds 80°C (176°F) 30 seconds 14 grams 50 per plastic tray / 1500 per carton box Rated Load UL, CUR 10 A at 30 VDC resistive 10 A at 250 VAC general use 1/4 HP 120 VAC 1/2 HP 250 VAC B 300 pilot duty 8 A at 250 VAC resistive, 100k cycles [1] 10 A at 250 VAC resistive, 50k cycles [2] Silver cadmium oxide [1] or silver tin oxide [2] < 30 milliohms initially VDE Material Resistance COIL Power At Pickup Voltage (typical) Max. Continuous Dissipation Temperature Rise Temperature 110 mW 140 mW (48 VDC coil) 1.5 W at 20°C (68°F) ambient 20°C (36°F) at nominal coil voltage Max. 110°C (230°F) Shock Enclosure Terminals Max. Solder Temp. Max. Solder Time Max. Solvent Temp. Max. Immersion Time Weight NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Specifications subject to change without notice. 4. It’s recommended to remove vent nipple on sealed versions to expand life expectancy when switching higher loads. Packing unit in pcs ZETTLER electronics GmbH Tel. +49 89 800 97 0 Fax +49 89 800 97 200 office@ZETTLERelectronics.com www.ZETTLERelectronics.com 2004-11-25 Junkersstrasse 3, D-82178 Puchheim, Germany AZ696 RELAY ORDERING DATA COIL SPECIFICATIONS Nominal Coil VDC 5 6 9 12 18 24 48 Must Operate VDC 3.5 4.2 6.3 8.4 12.6 16.8 33.6 Max. Continuous VDC 12.0 14.5 22.0 29.5 44.0 54.0 102.0 Coil Resistance Ohm ± 10% 110 160 360 660 1,500 2,200 8,000 ORDER NUMBER* 1 Form A (SPST-NO) AZ696–1A–5D AZ696–1A–6D AZ696–1A–9D AZ696–1A–12D AZ696–1A–18D AZ696–1A–24D AZ696–1A–48D 1 Form C (SPDT) AZ696–1C–5D AZ696–1C–6D AZ696–1C–9D AZ696–1C–12D AZ696–1C–18D AZ696–1C–24D AZ696–1C–48D * Substitute “1B” in place of “1A” for 1 Form B contact. Add suffix “E” to “1A” or “1B” or “1C” for silver tin oxide contacts. Add suffix “E” at the end of order number for sealed version. MECHANICAL DATA Coil Temperature Rise 1 FORM C 1 FORM A and 1FORM B 100 90 1.18 (30) .394 (10) 1.10 (28) .394 (10) 80 Coil Temperature Rise °C 70 60 50 40 30 20 10 0 60 80 100 120 140 10 A 0A FORM C .618 (15.7) .638 (16.2) .618 (15.7) .638 (16.2) .138 (3.5) .138 (3.5) .024 x .035 (0.6 x 0.9) .024 x .039 (0.6 x 1) .024 x .035 (0.6 x 0.9) .024 x .039 (0.6 x 1) 160 180 200 220 Percent of Nominal Coil Voltage at 20°C PC BOARD LAYOUT 1 FORM C 2 x ø .051 (ø 1.3) .299 (7.6.) 3 x ø .059 (ø 1.5) .126 (3.2) WIRING DIAGRAMS 1 1 FORM C 4 Maximum Switching Capacity 10.0 2 3 5 .122 (3.1) .748 (19.) .126 (3.2) 9.0 8.0 7.0 6.0 5.0 4.0 3.0 DC Resistive Load 1 FORM A 1 3 2.0 1 FORM A and 1 FORM B 2 x ø .051 (ø 1.3) .299 (7.6.) 2 x ø .059 (ø 1.5) 2 4 CURRENT AC Resistive Load 1.0 .9 .8 .7 .6 .5 1 FORM B 1 3 .4 .3 .2 10 100 .197 (5) 2 4 Viewed toward terminals Viewed toward terminals VOLTAGE Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" ZETTLER electronics GmbH Tel. +49 89 800 97 0 Fax +49 89 800 97 200 office@ZETTLERelectronics.com www.ZETTLERelectronics.com 2004-11-25 Junkersstrasse 3, D-82178 Puchheim, Germany 1000 .122 (3.1) .748 (19) .1 20 30 40 50 60 70 80 90 200 300 400 500 600 700 800 900