C-51496GNFJ-AB

First Edition Apr 15, 2002 OPTREX LCD Module Technical Specification C-51496GNFJ-AB Final Revision ****** Type No. Approved by (Production Div.) Checked by (Quality Assurance Div.) Checked by (Design Engineering Div.) Prepared by (Production Div.) Table of Contents 1. General Specifications .................................................................................................................................. 2 2. Electrical Specifications ............................................................................................................................... 3 3. Optical Specifications ................................................................................................................................... 6 4. I/O Terminal ...................................................................................................................................................... 8 5. Test ................................................................................................................................................................... 10 6. Appearance Standards ............................................................................................................................... 11 7. Code System of Production Lot ............................................................................................................... 14 8. Type Number.................................................................................................................................................. 14 9. Applying Precautions .................................................................................................................................. 14 10. Precautions Relating Product Handling................................................................................................ 15 11. Warranty ........................................................................................................................................................ 16 Revision History Rev. Date Page Comment C-51496GNFJ-AB (AB) No. 2002-0119 OPTREX CORPORATION Page 1/16 1. General Specifications Operating Temp. Storage Temp. Display Format Display Fonts Viewing Area Outline Dimensions : : : : : : min. -10°C ~ max. 60°C min. -20°C ~ max. 70°C 16 characters × 2 lines 5 × 8 dots ( 1 character ) 61.0 (W) × 16.5 (H) mm 64.0* (W) × 25.0** (H) × 2.2 max. (D) mm * Without Area of Injection Port **Without Flat Cable 7.4g max. NRD-21276 ( F-STN / Black &White-mode / Reflective ) 6:00 4-bit parallel data transfer Serial data transfer None Dimensional Outline UE-310928 Weight LCD Type : : Viewing Angle Data Transfer : : : : : Backlight Drawings C-51496GNFJ-AB (AB) No. 2002-0119 OPTREX CORPORATION Page 2/16 2. Electrical Specifications 2.1. Absolute Maximum Ratings GND=0V Parameter Supply Voltage (Logic) Supply Voltage (LCD Drive) Input Voltage VI -0.3 VCC +0.3 V V1OUT-V EE -0.3 7.0 V Symbol VCC -GND Conditions Min. -0.3 Max. 7.0 Units V 2.2. DC Characteristics Ta=25°C, GND=0V Parameter Supply Voltage (Logic) Supply Voltage (LCD Drive) High Level Input Voltage Low Level Input Voltage Supply Current ICC VCC -GND=3.0V 0.1 0.15 mA VIL VCC =2.8~3.2V -0.3 0.15× VCC V VIH 0.7× VCC VCC V V1OUT-V EE Shown in 3.1 V Symbol VCC -GND Conditions Min. 2.8 Typ. Max. 3.2 Units V C-51496GNFJ-AB (AB) No. 2002-0119 OPTREX CORPORATION Page 3/16 2.3. AC Characteristics 2.3.1. 4 Bit Bus Interface Timing VCC =2.8~3.2V Parameter Enable Cycle Time Enable High Level Pulse Width Enable Low Level Pulse Width Enable Rise/Fall Time Setup Time (RS to E,CS*) Address Hold Time Write Data Setup Time Write Data Hold Time V IH VIL Symbol Min. 500 80 250 60 20 60 20 V IH V IL Max. 25 - Units ns ns ns ns ns ns ns ns tCYCE PW EH PW EL tEr, tEf tASE tAHE tDSW E tHE RS/CS* tA S E PW EH tAHE PW E L V IH VIL V IL E/SCL V IH V IL t Er tDSW E DB0 /ID DB1 ∼ DB3 VIH V IL tE f tDHWE V IH V IL Valid Data tCYC C-51496GNFJ-AB (AB) No. 2002-0119 OPTREX CORPORATION Page 4/16 2.3.2. Serial Interface Sequence VCC =2.8∼3.2V Parameter Serial Clock Cycle Time Serial Clock High Level Width Serial Clock Low Level Width Serial Clock Rise/Fall Time Chip Select Setup Time Chip Select Hold Time Serial Input Data Setup Time Serial Input Data Hold Time Start: S Symbol Min. 0.2 80 80 60 200 40 40 Max. 20 20 End: P Units µs ns ns ns ns ns ns ns tSCYC tSCH tSCL tSC r, tSC f tCSU tCH tSISU tSIH RS/CS* V IL t CSU t SC r V IL t SCYC t SISU VIH VIL t SIH t SCH t SCL t SCf VIL V IL t CH E/SCL VIH V IH V IH SDA Valid Data Valid Data 2.3.3. Reset Timing Parameter Reset Low Level Width Symbol Conditions tRES RESET* VIL VIL Min. 1 Max. - Units ms tRES C-51496GNFJ-AB (AB) No. 2002-0119 OPTREX CORPORATION Page 5/16 3. Optical Specifications 3.1. LCD Driving Voltage Parameter Recommended LCD Driving Voltage Note 1 V1OUT-GND Symbol Conditions Ta= -10°C Ta=25°C Ta=60°C Min. 4.6 4.5 Typ. 5.0 Max. 5.1 5.3 Units V V V Note 1 : Voltage (Applied actual waveform to LCD Module) for the best contrast. The range of minimum and maximum shows tolerance of the operating voltage. The specified contrast ratio and response time are not guaranteed over the entire range. 3.2. Optical Characteristics Ta=25°C, 1/18 Duty, 1/5 Bias, VOD =5.0V (Note 4), θ= 0°, φ=-° Parameter Contrast Ratio Viewing Angle Response Time Rise Note 2 Decay Note 3 TON TOFF Note 1 Symbol CR Conditions θ= 0°,φ = -° Min. Typ. 6.5 Max. Units Shown in 3.3 110 120 200 200 ms ms Note 1 :Contrast ratio is definded as follows.(CR = LOFF / LON ) LON : Luminance of the ON segments LOFF : Luminance of the OFF segments Measuring Spot: 0.9mmφ Note 2 :The time that the luminance level reaches 90% of the saturation level from 0% when ON signal is applied. Note 3 :The time that the luminance level reaches 10% of the saturation level from 100% when OFF signal is applied. Note 4 :Definition of Driving Voltage VOD Assuming that the typical driving waveforms shown below are applied to the LCD Panel at 1/A Duty - 1/B Bias (A: Duty Number, B: Bias Number). Driving voltage VOD is definded as follows. VOD = (Vth1+Vth2) / 2 Vth1: The voltage VO-P that should provide 70% of the saturation level in the luminance at the segment which the ON signal is applied to. Vth2: The voltage VO-P that should provide 20% of the saturation level in the luminance at the segment which the OFF signal is applied to. Vo-p ( B-2 ) ×Vo-p/B 1/( f F× A ) 1 /f F ( ON SIGNAL ) ( OFF SIGNAL ) C-51496GNFJ-AB (AB) No. 2002-0119 OPTREX CORPORATION Page 6/16 3.3. Definition of Viewing Angle and Optimum Viewing Area *Point • shows the point where contrast ratio is measured. : θ= 0°, φ= -° *Driving condition: 1/18 Duty, 1/5 Bias, VOD =5.0V, fF =88Hz 90° 135° 45° φ 180° ( φ = 0°) θ 90° 10 20 30 40 50 θ 180° 225° 270° φ 0° 315° 270° *Area   shows typ. CR≥3 (Measuring Spot: 0.9mmφ) 3.4. System Block Diagram Temperature Chamber Rotation Table ( θ,φ ) Photometer #1980A WB φ LCD Optical Fiber θ Computer Control Unit & Waveform Generator Halogen bulb C-51496GNFJ-AB (AB) No. 2002-0119 OPTREX CORPORATION Page 7/16 4. I/O Terminal 4.1. Pin Assignment CN1 No. 1 2 Symbol NC IM2 Non-connection Interface Mode Select Signal H : Data Bus Mode L : Serial Mode 3 IM1 Interface Mode Select Signal H : Data Bus Mode L : Serial Mode 4 5 6 7 8 9 DB3 DB2 DB1 DB0/ID RESET* RS/CS* Data Bus Line Data Bus Line Data Bus Line Data Bus Line Reset Signal L : Reset Register Select Signal L:Instraction H:Data Chip Select Signal L : Active 10 E/SCL Input for Serial Clock Enable Signal 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 SDA GND VCC CAP2+ CAP2CAP1+ CAP1VLOUT VLCD V1OUT V2OUT V3OUT V4OUT V5OUT NC Input for Serial Data Power Supply ( 0V, GND ) Power Supply for Logic DC/DC Voltage Converter Capacitor 2 Positive Connection DC/DC Voltage Converter Capacitor 2 Negative Connection DC/DC Voltage Converter Capacitor 1 Positive Connection DC/DC Voltage Converter Capacitor 1 Negative Connection DC/DC Voltage Converter Output Power Supply for LCD Drive Output Terminal of Internal Operational Amplifier Output Terminal of Internal Operational Amplifier Output Terminal of Internal Operational Amplifier Output Terminal of Internal Operational Amplifier Output Terminal of Internal Operational Amplifier Non-connection Function C-51496GNFJ-AB (AB) No. 2002-0119 OPTREX CORPORATION Page 8/16 4.2. Block Diagram V5OUT V4OUT V3OUT V2OUT V1OUT VLCD VLOUT C1C1+ C2C2+ VCC GND SDA E/SCL HCD66704 Control LSI SEG 80 LCDP COM 16 16 Characters × 2 Lines RS/CS* RESET* DB0/ID DB1 DB2 DB3 IM1 IM2 C-51496GNFJ-AB (AB) No. 2002-0119 OPTREX CORPORATION Page 9/16 5. Test No change on display and in operation under the following test condition. Conditions: Unless otherwise specified, tests will be conducted under the following condition. Temperature: 20±5°C Humidity : 65±5%RH tests will be not conducted under functioning state. Parameter High Temperature Operating Low Temperature Operating High Temperature Storage Low Temperature Storage Damp Proof Test Vibration Test Conditions 60°C±2°C, 96hrs (operation state) -10°C±2°C, 96hrs (operation state) 70°C±2°C, 96hrs -20°C±2°C, 96hrs 40°C±2°C,90~95%RH, 96hrs Total fixed amplitude : 1.5mm Vibration Frequency : 10~55Hz One cycle 60 seconds to 3 directions of X, Y, Z for each 15 minutes 7 Shock Test To be measured after dropping from 60cm high on the concrete surface in packing state. Dropping method corner dropping F E B 60cm Concrete Surface G D A C A corner : once Edge dropping B,C,D edge : once Face dropping E,F,G face : once No. 1 2 3 4 5 6 Notes 1 2 1,2 1,2 3 Note 1 :No dew condensation to be observed. Note 2 :The function test shall be conducted after 4 hours storage at the normal Temperature and humidity after removed from the test chamber. Note 3 :Vibration test will be conducted to the product itself without putting it in a container. C-51496GNFJ-AB (AB) No. 2002-0119 OPTREX CORPORATION Page 10/16 6. Appearance Standards 6.1. Inspection conditions The LCD shall be inspected under 40W white fluorescent light. The distance between the eyes and the sample shall be more than 30cm. All directions for inspecting the sample should be within 45°against perpendicular line. 45° 6.2. Definition of applicable Zones X X X A Zone B Zone X C Zone X : Maximum Seal Line A Zone : Active display area B Zone : Out of active display area ~ Maximum seal line C Zone : Rest parts A Zone + B Zone = Validity viewing area C-51496GNFJ-AB (AB) No. 2002-0119 OPTREX CORPORATION Page 11/16 6.3. Standards No. 1 Parameter Black and White Spots, Foreign Substances Dimension (mm) D ≤ 0.1 0.1 < D ≤ 0.2 0.2 < D ≤ 0.3 0.3 < D D = ( Long + Short ) / 2 (2) Line Shape Zone X(mm) 2.0≥L 1.0≥L 1.0≥L Y(mm) 0.02≥W 0.03≥W 0.04≥W 0.05≥W 0.05