CX72302

DATA SHEET CX72302: Spur-Free, 6.1 GHz Dual Fractional-N Frequency Synthesizer Applications • General purpose RF systems • 2.5G and 3G wireless infrastructures • Broadband wireless access • Low bit rate wireless telemetry • Wireless Local Loop (WLL) • Instrumentation Description Skyworks CX72302 direct digital modulation fractional-N frequency synthesizer provides ultra-fine frequency resolution, fast switching speed, and low phase-noise performance. This synthesizer is a key building block for high-performance radio system designs that require low power and fine step size. The ultra-fine step size of less than 400 Hz allows this synthesizer to be used in very narrowband wireless applications. With proper temperature sensing or through control channels, the synthesizer’s fine step size can compensate for crystal oscillator or Intermediate Frequency (IF) filter drift. As a result, crystal oscillators or crystals can replace temperature-compensated or ovenized crystal oscillators, reducing parts count and associated component cost. The device’s fine step size can also be used for Doppler shift corrections. The CX72302 has a phase noise floor of –80 dBc/Hz up to 6.1 GHz operation as measured inside the loop bandwidth. This is permitted by the on-chip low noise dividers and low divide ratios provided by the device’s high fractionality. Reference crystals or oscillators up to 50 MHz can be used with the CX72302. The crystal frequency is divided down by independent programmable dividers (1 to 32) for the main and auxiliary synthesizers. The phase detectors can operate at a maximum speed of 25 MHz, which allows better phase noise due to the lower division value. With a high reference frequency, the loop bandwidths can also be increased. Larger loop bandwidths improve the settling times and reduce in-band phase noise. Therefore, typical switching times of less than 100 µs can be achieved. The lower in-band phase noise also permits the use of lower cost Voltage Controlled Oscillators (VCOs) in customer applications. The CX72302 has a frequency power steering circuit that helps the loop filter to steer the VCO when the frequency is too fast or too slow, further enhancing acquisition time. The unit operates with a three-wire, high-speed serial interface. A combination of a large bandwidth, fine resolution, and the threewire, high-speed serial interface allows for a direct frequency modulation of the VCO. This supports any continuous phase, constant envelope modulation scheme such as Frequency Modulation (FM), Frequency Shift Keying (FSK), Minimum Shift Keying (MSK), or Gaussian Minimum Shift Keying (GMSK). Features • Spur-free operation • 6.1 GHz maximum operating frequency • 1000 MHz maximum auxiliary synthesizer • Ultra-fine step size, 400 Hz or less • High internal reference frequency enables large loop bandwidth implementations • Very fast switching speed (e.g., below 100 µs) • Phase noise to –80 dBc/Hz inside loop filter bandwidth @ 6100 MHz • Software programmable power-down modes • High speed serial interface up to 100 Mbps • Three-wire programming • Programmable division ratios on reference frequency • Phase detectors with programmable gains to provide a programmable loop bandwidth • Frequency power steering further enhances rapid acquisition time • On-chip crystal oscillator • Frequency adjust for temperature compensation • Direct digital modulation • 3 V operation • 5 V output to loop filter • 28-pin EP-TSSOP 6.4 x 9.7 mm package Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 101216G • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • July 22, 2004 1 DATA SHEET • CX72302 This capability can eliminate the need for In-Phase and Quadrature (I/Q) Digital-to-Analog Converters (DACs), quadrature upconverters, and IF filters from the transmitter portion of the radio system. Figure 1 shows a functional block diagram for the CX72302. The device package and pinout for the 28-pin Exposed Pad Thin Shrink Small Outline Package (EP-TSSOP) are shown in Figure 2. Data Clock CS Serial Interface Modulator Data Main ∆Σ Main Divider Registers Modulator Control Ref. Divider Synth Control Aux. Divider Aux. ∆Σ Mod_in Modulation Unit Mux Mux_out ∆Σ 18-Bit ∆Σ 10-Bit Fractional Unit Fvco_main Fvco_main Main Divider Main Divider Fpd_main Reference Frequency Oscillator Fractional Unit Fvco_aux Auxiliary Divider Auxiliary Prescaler Fvco_aux Fref_main Fref_aux Fpd_aux Main Phase/Freq. Detector and Charge Pump Fref Reference Frequency Oscillator Auxiliary Phase/Freq. Detector and Charge Pump CPout_main Lock Detection or Power Steering LD/PSmain CPout_aux LD/PSaux Lock Detection or Power Steering C1447 Figure 1. CX72302 Functional Block Diagram Clock Mod_in Mux_out VSUBdigital GNDcml VCCcml_main Fvco_main Fvco_main LD/PSmain VCCcp_main CPout_main GNDcp_main Xtalacgnd/OSC Xtalin/OSC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 CS Data VCCdigital GNDdigital VCCcml_aux Fvco_aux Fvco_aux GNDcp_aux CPout_aux VCCcp_aux LD/PSaux GNDxtal VCCxtal Xtalout/NC C1412 Figure 2. CX72302 Pinout, 28-Pin EP-TSSOP (Top View) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 2 July 22, 2004 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 101216G DATA SHEET • CX72302 Technical Description The CX72302 is a fractional-N frequency synthesizer using a ∆Σ modulation technique. The fractional-N implementation provides low in-band noise by having a low division ratio and fast frequency settling time. In addition, the CX72302 provides arbitrarily fine frequency resolution with a digital word, so that the frequency synthesizer can be used to compensate for crystal frequency drift in the RF transceiver. Serial Interface The serial interface is a versatile three-wire interface consisting of three pins: Clock (serial clock), Data (serial input), and CS (chip select). It enables the CX72302 to operate in a system where one or multiple masters and slaves are present. To perform a loopback test at start-up and to check the integrity of the board and processor, the serial data is fed back to the master device (e.g., a microcontroller or microprocessor unit) through a programmable multiplexer. This facilitates hardware and software debugging. Registers There are ten 16-bit registers in the CX72302. For more information, see the Register Descriptions section of this document. Main and Auxiliary ∆Σ Modulators The fractionality of the CX72302 is accomplished by the use of a proprietary, configurable 10-bit or 18-bit ∆Σ modulator for the main synthesizer and 10-bit ∆Σ modulator for the auxiliary synthesizer. Main and Auxiliary Fractional Units The CX72302 provides fractionality through the use of main and auxiliary ∆Σ modulators. The output from the modulators is combined with the main and auxiliary divider ratios through their respective fractional units. VCO Prescalers The VCO prescalers provide low-noise signal conditioning of the VCO signals. They translate from an off-chip, single-ended or differential signal to an on-chip differential Current Mode Logic (CML) signal. The CX72302 has independent main and auxiliary VCO prescalers. Main and Auxiliary VCO Dividers The CX72302 provides programmable dividers that control the CML prescalers and supply the required signals to the charge pump phase detectors. Programmable divide ratios ranging from 152 to 2148 are possible in fractional-N mode, and from 128 to 2172 in integer-N mode. Note that due to the fixed divide-by-four divider on the main synthesizer, the divide ratios are multiples of four. Programmable divide ratios ranging from 38 to 537 are possible in fractional-N mode, and from 32 to 543 in integer-N mode for the auxiliary synthesizer. Reference Frequency Oscillator The CX72302 has a self-contained, low-noise crystal oscillator. This crystal oscillator is followed by the clock generation circuitry that generates the required clock for the programmable reference frequency dividers. Reference Frequency Dividers The crystal oscillator signal can be divided by a ratio of 1 to 32 to create the reference frequencies for the phase detectors. The CX72302 has both a main and auxiliary frequency synthesizer, and provides independently configurable dividers of the crystal oscillator frequency for both the main and auxiliary phase detectors. The divide ratios are programmed through the Reference Frequency Dividers Register. NOTE: The divided crystal oscillator frequencies (which are the internal reference frequencies), Fref_main and Fref_aux, are referred to as reference frequencies throughout this document. Phase Detectors and Charge Pumps The CX72302 uses a separate charge pump phase detector for each synthesizer which provides a programmable gain, Kd, from 31.25 to 1000 µA/2π radians in 32 steps programmed using the Control Register. Frequency Steering When programmed for frequency power steering, the CX72302 has a circuit that helps the loop filter steer the VCO, through the LD/PSmain signal (pin 9). In this configuration, the LD/PSmain signal can provide for more rapid acquisition. When programmed for lock detection, internal frequency steering is implemented and provides frequency acquisition times comparable to conventional phase/frequency detectors. Lock Detection When programmed for lock detection, the CX72302 provides an active low, pulsing open collector output using the LD/PSmain signal (pin 9) to indicate the out-of-lock condition. When locked, the LD/PSmain signal is three-stated (high impedance). Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 101216G • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • July 22, 2004 3 DATA SHEET • CX72302 Power Down The CX72302 supports a number of power-down modes through the serial interface. For more information, see the Register Descriptions section of this document. present and that all the bits in the stream should be loaded into the Modulation Data Register. Synthesizer Register Programming Synthesizer register programming equations, described in this section, use the following variables and constants: Nfractional Desired VCO division ratio in fractional-N applications. This is a real number and can be interpreted as the reference frequency (Fref) multiplying factor such that the resulting frequency is equal to the desired VCO frequency. Desired VCO division ratio in integer-N applications. This number is an integer and can be interpreted as the reference frequency (Fref) multiplying factor so that the resulting frequency is equal to the desired VCO frequency. 9-bit unsigned input value to the divider ranging from 0 to 511 (integer-N mode) and from 6 to 505 (fractional-N mode). This constant equals 262144 when the ∆Σ modulator is in 18-bit mode, and 1024 when the ∆Σ modulator is in 10-bit mode. Operation This section describes the operation of the CX72302. The serial interface is described first, followed by information on how to obtain values for the Divide Ratio Registers. Serial Interface The serial interface consists of three pins: Clock (pin 1), Data (pin 27), and CS (pin 28). The Clock signal controls data on the two serial data lines (Data and CS). The Data pin bits shift into a temporary register on the rising edge of Clock. The CS line allows individual selection transfers that synchronize and sample the information of slave devices on the same bus. Figure 3 functionally depicts how a serial transfer takes place. A serial transfer is initiated when a microcontroller or microprocessor forces the CS line to a low state. This is followed immediately by an address/data stream sent to the Data pin that coincides with the rising edges of the clock presented on the Clock line. Each rising edge of the Clock signal shifts in one bit of data on the Data line into a shift register. At the same time, one bit of data is shifted out of the Mux_out pin (if the serial bit stream is selected) at each falling edge of Clock. To load any of the synthesizer registers, 16 bits of address or data must be presented to the Data line with the data LSB last while CS is low. If CS is low for more than 16 clock cycles, only the last address or data bits are used to load the synthesizer registers. If the CS line is brought to a high state before the 13th clock edge on Clock, the bit stream is assumed to be modulation data samples. In this case, it is assumed that no address bits are Ninteger Nreg divider dividend When in 18-bit mode, this is the 18-bit signed input value to the ∆Σ modulator, ranging from –131072 to +131071 and providing 262144 steps, each of Fdiv_ref/218 Hz. When in 10-bit mode, this is the 10-bit signed input value to the ∆Σ modulator, ranging from –512 to +511 and providing 1024 steps, each of Fdiv_ref/210 Hz. FVCO Fdiv_ref Desired VCO frequency (either Fvco_main or Fvco_aux). Divided reference frequency presented to the phase detector (either Fref_main or Fref_aux). Clock Data X A3 A2 A1 A0 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 XXX CS Last C1413 Figure 3. Serial Transfer Timing Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 4 July 22, 2004 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 101216G DATA SHEET • CX72302 Fractional-N Applications. The desired division ratio for the main synthesizer is given by: F VCO _ main Nfrac tion al = --------------------------------4 Fdiv _ r ef NOTE: As with all integer-N synthesizers, the minimum step size is related to the crystal frequency and reference frequency division ratio. A sample calculation for an integer-N application is provided in Figure 5. Register Loading Order. In applications where the main synthesizer is in 18-bit mode, the Main Dividend MSB Register holds the 10 MSBs of the dividend and the Main Dividend LSB Register holds the 8 LSBs of the dividend. The registers that control the main synthesizer’s divide ratio are to be loaded in the following order: • Main Divider Register • Main Dividend LSB Register • Main Dividend MSB Register (at which point the new divide ratio takes effect) In applications where the main synthesizer is in 10-bit mode, the Main Dividend MSB Register holds the 10 bits of the dividend. The registers that control the main synthesizer’s divide ratio are to be loaded in the following order: • Main Divider Register • Main Dividend MSB Register (at which point the new divide ratio takes effect) For the auxiliary synthesizer, the Auxiliary Dividend Register holds the 10 bits of the dividend. The registers that control the auxiliary synthesizer’s divide ratio are to be loaded in the following order: • Auxiliary Divider Register • Auxiliary Dividend Register (at which point the new divide ratio takes effect) NOTE: When in integer mode, the new divide ratios take effect as soon as the Main or Auxiliary Divider Register is loaded. Direct Digital Modulation The high fractionality and small step size of the CX72302 allow the user to tune to practically any frequency in the VCO’s operating range. This frequency tuning allows direct digital modulation by programming the different desired frequencies at precise instants. Typically, the channel frequency is selected through the Main Divider and Dividend Register and the instantaneous frequency offset from the carrier is entered through the Modulation Data Register. The Modulation Data Register can be accessed in three ways, which are defined in the following subsections. The desired division ratio for the auxiliary synthesizer is given by: F VCO _ aux Nfrac tion al = -----------------------F div _ r ef where Nfractional must be between 150 and 2150 for the main synthesizer or between 37.5 and 537.5 for the auxiliary synthesizer. The value to be programmed in the Main or Auxiliary Divider Register is given by: N reg = Round ( N fractional ) − 32 NOTE: The Round function rounds the number to the nearest integer. When in fractional mode, allowed values for Nreg are from 6 to 505 inclusive. The value to be programmed in the Main or Auxiliary Dividend Register is given by: dividend = Round [ divider ×( N fractional − N reg − 32 )] where the divider is either 1024 in 10-bit mode or 262144 in 18-bit mode. Therefore, the dividend is a signed binary value either 10 or 18 bits long. NOTE: Because of the high fractionality of the CX72302, there is no practical need for any integer relationship between the reference frequency and the channel spacing or desired VCO frequencies. Sample calculations for two fractional-N applications are provided in Figure 4. Integer-N Applications. The desired division ratio for the main or auxiliary synthesizer is given by: N int eger = Fvco _ main Fdiv _ ref where Ninteger is an integer number from 32 to 543 for both the main and auxiliary synthesizers. The value to be programmed in the Main or Auxiliary Divider Register is given by: N reg = N int eger − 32 When in integer mode, allowed values for Nreg are from 0 to 511 for both the main and auxiliary synthesizers. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 101216G • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • July 22, 2004 5 DATA SHEET • CX72302 Case 1: To achieve a desired Fvco_main frequency of 5900.4530 MHz using a crystal frequency of 40 MHz with operation of the synthesizer in 18-bit mode. Since the maximum internal reference frequency (Fdiv_ref) is 25 MHz, the crystal frequency is divided by 2 to obtain a Fdiv_ref of 20 MHz. Therefore: Nfractional = Fvco_main 4 × Fdiv_ref = 5900.4530 80 = 73.755663 The value to be programmed in the Main Divider Register is: Nreg = Round[Nfractional] – 32 = Round[73.755663] – 32 = 74 – 32 = 42 (decimal) = 000101010 (binary) With the modulator in 18-bit mode, the value to be programmed in the Main Dividend Registers is: dividend = Round[divider × (Nfractional – Nreg – 32)] = Round[262144 × (73.755663 – 42 – 32)] = Round[262144 × (–0.2443375)] = Round[–64051.6096] = –64052 (decimal) = 110000010111001100 (binary) where 11 0000 0101 is loaded in the MSB of the Main Dividend Register and 11001100 is loaded in the LSB of the Main Dividend Register. Summary: · · · · Main Divider Register = 0 0010 1010 Main Dividend LSB Register = 1100 1100 Main Dividend MSB Register = 11 0000 0101 The resulting main VCO frequency is 5900.4529 MHz Note: The frequency step size for this case is 4 × 20 MHz divided by 218, giving 305.2 Hz. C1449 Figure 4. Fractional-N Applications: Sample Calculation (1 of 2) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 6 July 22, 2004 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 101216G DATA SHEET • CX72302 Case 2: To achieve a desired Fvco_main frequency of 5217.1776 MHz using a crystal frequency of 19.2 MHz with operation of the synthesizer in 10-bit mode. Since the maximum internal reference frequency (Fdiv_ref) is 25 MHz, the crystal frequency does not require the internal division to be greater than 1, which makes Fdiv_ref = 19.2 MHz. Therefore: Nfractional = Fvco_main 4 × Fdiv_ref = 5217.1776 4 × 19.2 = 67.9320 The value to be programmed in the Main Divider Register is: Nreg = Round[Nfractional] – 32 = Round[67.9320] – 32 = 68 – 32 = 36 (decimal) = 000100100 (binary) With the modulator in 10-bit mode, the value to be programmed in the Main Dividend Registers is: dividend = Round[divider × (Nfractional – Nreg – 32)] = Round[1024 × (67.9320 – 36 – 32)] = Round[1024 × (– 0.068)] = Round[– 69.632] = –70 (decimal) = 1110111010 (binary) where 11 1011 1010 is loaded in the MSB of the Main Dividend Register. Summary: · · · Main Divider Register = 0 0010 0100 Main Dividend MSB Register = 11 1011 1010 The resulting main VCO frequency is 5217.15 MHz Note: The frequency step size for this case is 4 × 19.2 MHz divided by 210, giving 75 kHz. C1450 Figure 4. Fractional-N Applications: Sample Calculation (2 of 2) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 101216G • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • July 22, 2004 7 DATA SHEET • CX72302 To achieve a desired Fvco_aux frequency of 400 MHz using a crystal frequency of 16 MHz. Since the minimum divide ratio is 32, the reference frequency (Fdiv_ref) must be a maximum of 12.5 MHz. Choosing a reference frequency divide ratio of 2 provides a reference frequency of 8 MHz. Therefore: Ninteger = Fvco_aux Fdiv_ref = = 400 8 50 The value to be programmed in the Auxiliary Divider Register is: Nreg = Ninteger – 32 = 50 – 32 = 18 (decimal) = 000010010 (binary) Summary: · Auxiliary Divide Register = 0 0001 0010 C1416 Figure 5. Integer-N Applications: Sample Calculation Normal Register Write. A normal 16-bit serial interface write occurs when CS is 16 clock cycles wide. The corresponding 16-bit modulation data is simultaneously presented to the Data pin. The content of the Modulation Data Register is passed to the modulation unit at the next falling edge of the divided main VCO frequency (Fpd_main). Short CS Through Data Pin (No Address Bits Required). A shortened serial interface write occurs when CS is from 2 to 12 clock cycles wide. The corresponding modulation data (2 to 12 bits) is simultaneously presented to the Data pin. The Data pin is the default pin used to enter modulation data directly in the Modulation Data Register with shortened CS strobes. This method of data entry eliminates the register address overhead on the serial interface. All serial interface bits are re-synchronized internally at the reference oscillator frequency. The content of the Modulation Data Register is passed to the modulation unit at the next falling edge of the divided main VCO frequency (Fpd_main). Short CS Through Mod_in Pin (No Address Bits Required). A shortened serial interface write occurs when CS is from 2 to 12 clock cycles wide. The corresponding modulation data (2 to 12 bits) is simultaneously presented to the Mod_in pin. The Mod_in pin is the alternate pin used to enter modulation data directly into the Modulation Data Register with shortened CS strobes. This mode is selected through the Modulation Control Register. This method of data entry also eliminates the register address overhead on the serial interface and allows a different device than the one controlling the channel selection to enter the modulation data (e.g., a microcontroller for channel selection and a digital signal processor for modulation data). All serial interface bits are re-synchronized internally at the reference oscillator frequency and the content of the Modulation Data Register is passed to the modulation unit at the next falling edge of the divided main VCO frequency (Fpd_main). Modulation data samples in the Modulation Data Register can be from 2 to 12 bits long, and enable the user to select how many distinct frequency steps are to be used for the desired modulation scheme. The user can also control the frequency deviation through the modulation data magnitude offset in the Modulation Control Register. This allows shifting of the modulation data to accomplish a 2m multiplication of frequency deviation. NOTE: The programmable range of –0.5 to +0.5 of the main modulator can be exceeded up to the condition where the sum of the dividend and the modulation data conform to: −0.5625 ≤ ( N mod + dividend ) ≤ + 0.5625 When the sum of the dividend and modulation data lie outside this range, the value of Ninteger must be changed. For a more detailed description of direct digital modulation functionality, refer to the Skyworks Application Note, Direct Digital Modulation Using the CX72300, CX72301, and CX72302 Dual Synthesizers/PLLs (document number 101349). Register Descriptions This section describes the CX72302 registers. All register writes are programmed address first, followed directly with data. MSBs are entered first. On power-up, all registers are reset to 0x000 except registers at address 0x0 and 0x3, which are set to 0x006. Table 1 provides a description for each of the CX72302 device registers. For more information on register loading, refer to the Synthesizer Register Programming section in this document. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 8 July 22, 2004 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 101216G DATA SHEET • CX72302 Table 1. CX72302 Register Map Address (Hex) 0 1 2 3 4 5 6 7 8 9 — Main Divider Register Main Dividend MSB Register Main Dividend LSB Register Auxiliary Divider Register Auxiliary Dividend Register Reference Frequency Dividers Register Control Register—phase detector/charge pumps Control Register—power down/multiplexer output select Modulation Control Register Modulation Data Register Modulation Data Register (Note 2) — direct input Register (Note 1) Length (Bits) 12 12 12 12 12 12 12 12 12 12 2 ≤ length ≤ 12 bits Address (Bits) 4 4 4 4 4 4 4 4 4 4 0 Note 1: All registers are write only. Note 2: No address bits are required for modulation data. Any serial data between 2 and 12 bits long is considered modulation data. A3 0 A2 A1 0 0 A0 11 0 X 10 X 9 8 7 6 5 4 3 2 1 0 LSB X MSB Main Synthesizer Divider Index C1417 Figure 6. Main Divider Register (Write Only) Synthesizer Registers Main Synthesizer Registers. The Main Divider Register contains the integer portion closest to the desired fractional-N (or the integer-N) value minus 32 for the main synthesizer. This register, in conjunction with the Main Dividend Registers (which control the fraction offset from –0.5 to +0.5), allows selection of a precise frequency. NOTE: The fixed divide-by-four divider upstream from the programmable main divider must be taken into consideration to determine the value to be programmed in this register. For more information, refer to the Synthesizer Register Programming section in this document. As shown in Figure 6, the value to be loaded is: • Main Synthesizer Divider Index = 9-bit value for the integer portion of the main synthesizer dividers. Valid values for this register are from 6 to 505 (fractional-N) or 0 to 511 (integer-N). The Main Dividend MSB and LSB Registers control the fraction part of the desired fractional-N value and allow an offset of –0.5 to + 0.5 to the main integer selected through the Main Divider Register. As shown in Figures 7 and 8, the values to be loaded are: • Main Synthesizer Dividend (MSBs) = 10-bit value for the MSBs of the 18-bit dividend for the main synthesizer. • Main Synthesizer Dividend (LSBs) = 8-bit value for the LSBs of the 18-bit dividend for the main synthesizer. The Main Dividend MSB and LSB Register values are 2's complement format. NOTE: When in 10-bit mode, the Main Synthesizer Dividend (LSBs) is not required. For information on programming and loading order for these registers, see the Operation section in this document. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 101216G • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • July 22, 2004 9 DATA SHEET • CX72302 A3 0 A2 A1 0 0 A0 11 1 X 10 9 8 7 6 5 4 3 2 1 0 LSB X MSB Main Synthesizer Dividend (MSBs) C1418 Figure 7. Main Dividend MSB Register (Write Only) A3 0 A2 A1 0 1 A0 11 0 X 10 X 9 X 8 7 6 5 4 3 2 1 0 LSB X MSB Main Synthesizer Dividend (LSBs) C1419 Figure 8. Main Dividend LSB Register (Write Only) A3 0 A2 A1 0 1 A0 11 1 X 10 X 9 8 7 6 5 4 3 2 1 0 LSB X MSB Auxiliary Synthesizer Divider Index C1420 Figure 9. Auxiliary Divider Register (Write Only) Auxiliary Synthesizer Registers. The Auxiliary Divider Register contains the integer portion closest to the desired fractional-N (or integer-N) value minus 32 for the auxiliary synthesizer. This register, in conjunction with the Auxiliary Dividend Register, which controls the fraction offset (from –0.5 to +0.5) allows selection of a precise frequency. As shown in Figure 9, the value to be loaded is: • Auxiliary Synthesizer Divider Index = 9-bit value for the integer portion of the auxiliary synthesizer dividers. Valid values for this register are from 6 to 505 (fractional-N) or from 0 to 511 (integer-N). The Auxiliary Dividend Register controls the fraction part of the desired fractional-N value and allows an offset of –0.5 to +0.5 to the auxiliary integer selected through the Auxiliary Divider Register. As shown in Figure 10, the value to be loaded is: • Auxiliary Synthesizer Dividend = 10-bit value for the dividend for the auxiliary synthesizer. For information on programming and loading order for these registers, refer to the Operation section of this document. General Synthesizer Registers. The Reference Frequency Dividers Register configures the dual-programmable reference frequency dividers for the main and auxiliary synthesizers. The dual-programmable reference frequency dividers provide the reference frequencies to the phase detectors by dividing the crystal oscillator frequency. The lower five bits hold the reference frequency divide index for the main phase detector. The next five bits hold the reference frequency divide index for the auxiliary phase detector. Divide ratios from 1 to 32 are possible for each reference frequency divider (see Tables 2 and 3). As shown in Figure 11, the values to be loaded are: • Main Reference Frequency Divider Index = Desired main oscillator frequency division ratio –1. Default value on power-up is 0, signifying that the reference frequency is not divided for the main phase detector. • Auxiliary Reference Frequency Divider Index = Desired auxiliary oscillator frequency division ratio –1. Default value on power-up is 0, signifying that the reference frequency is not divided for the auxiliary phase detector. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 10 July 22, 2004 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 101216G DATA SHEET • CX72302 A3 0 A2 A1 1 0 A0 11 0 X 10 9 8 7 6 5 4 3 2 1 0 LSB X MSB Auxiliary Synthesizer Dividend C1421 Figure 10. Auxiliary Dividend Register (Write Only) Table 2. Programming the Main Reference Frequency Divider Decimal 0 1 2 — — — 31 Bit 4 (MSB) 0 0 0 — — — 1 Bit 3 0 0 0 — — — 1 Bit 2 0 0 0 — — — 1 Bit 1 0 0 1 — — — 1 Bit 0 (LSB) 0 1 0 — — — 1 Reference Divider Ratio 1 2 3 — — — 32 Table 3. Programming the Auxiliary Reference Frequency Divider Decimal 0 1 2 — — — 31 Bit 9 (MSB) 0 0 0 — — — 1 Bit 8 0 0 0 — — — 1 Bit 7 0 0 0 — — — 1 Bit 6 0 0 1 — — — 1 Bit 5 (LSB) 0 1 0 — — — 1 Reference Divider Ratio 1 2 3 — — — 32 A3 0 A2 A1 1 0 A0 11 1 X 10 X 9 8 7 6 5 4 3 2 1 0 Main Reference Frequency Divider Index Auxiliary Reference Frequency Divider Index C1422 Figure 11. Reference Frequency Dividers Register (Write Only) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 101216G • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • July 22, 2004 11 DATA SHEET • CX72302 The Control Register allows control of the gain for both phase detectors and configuration of the LD/PSmain and LD/PSaux pins for frequency power steering or lock detection. As shown in Figure 12, the values to be loaded are: • Main Phase Detector Gain = 5-bit value for programmable main phase detector gain. Range is from 0 to 31 decimal for 31.25 to 1000 µA/2π radian, respectively. • Main Power Steering Enable = 1-bit value to enable the frequency power steering circuitry of the main phase detector. When this bit is a 0, the LD/PSmain pin is configured to be a lock detect, active-low, open collector pin. When this bit is a 1, the LD/PSmain pin is configured to be a frequency power steering pin and can be used to bypass the external main loop filter to provide faster frequency acquisition. • Auxiliary Phase Detector Gain = 5-bit value for programmable auxiliary phase detector gain. Range is from 0 to 31 decimal for 31.25 to 1000 µA/2π radian, respectively. • Auxiliary Power Steering Enable = 1-bit value to enable the frequency power steering circuitry of the auxiliary phase detector. When this bit is a 0, the LD/PSaux pin is configured to be a lock detect, active-low, open collector pin. When this bit is a 1, the LD/PSaux pin is configured to be a frequency power steering pin and may be used to bypass the external auxiliary loop filter to provide faster frequency acquisition. The Power Down and Multiplexer Output Register allows control of the power-down modes, internal multiplexer output, and main ∆Σ synthesizer fractionality. As shown in Figure 13, the values to be loaded are: • Full Power Down = 1-bit value that powers down the CX72302 except for the reference oscillator and the serial interface. When this bit is 0, the CX72302 is powered up. When this bit is 1, the CX72302 is in full power-down mode excluding the Mux_out pin. • Main Synthesizer Power Down = 1-bit value that powers down the main synthesizer. When this bit is 0, the main synthesizer is powered up. When this bit is 1, the main synthesizer is in power-down mode. A3 0 A2 A1 1 1 A0 11 0 10 9 8 7 6 5 4 3 2 1 0 Main Phase Detector Gain Main Power Steering/Lock Detect Enable Auxiliary Phase Detector Gain Auxiliary Power Steering/Lock Detect Enable C1423 Figure 12. Control Register (Write Only) A3 0 A2 A1 1 1 A0 11 1 X 10 X 9 8 MSB 7 6 LSB 5 4 3 2 1 0 Full Power Down Main Synthesizer Power Down Main Synthesizer Mode Main Synthesizer ∆Σ Fractionality Auxiliary Synthesizer Power Down Auxiliary Synthesizer Mode Multiplexer Output Selection Mux_out Pin Three-State Enable C1424 Figure 13. Power Down and Multiplexer Output Register (Write Only) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 12 July 22, 2004 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 101216G DATA SHEET • CX72302 • Main Synthesizer Mode = 1-bit value that powers down the main synthesizer’s ∆Σ modulator and fractional unit to operate as an integer-N synthesizer. When this bit is 0, the main synthesizer is in fractional-N mode. When this bit is 1, the main synthesizer is in integer-N mode. • Main Synthesizer ∆Σ Fractionality = 1-bit value that configures the size of the main ∆Σ modulator. This has a direct effect on power consumption and on the level of fractionality and step size. When this bit is 0, the main ∆Σ modulator is 18-bit with a fractionality of 218 and a step size of Fref_main/262144. When this bit is 1, the main ∆Σ modulator is 10-bit with a fractionality of 210 and a step size of Fref_main/1024. • Auxiliary Synthesizer Power Down = 1-bit value that powers down the auxiliary synthesizer. When this bit is 0, the auxiliary synthesizer is powered up. When this bit is 1, the auxiliary synthesizer is in power-down mode. • Auxiliary Synthesizer Mode = 1-bit value that powers down the auxiliary synthesizer’s ∆Σ modulator and fractional unit to operate as an integer-N synthesizer. When this bit is 0, the auxiliary synthesizer is in fractional-N mode. When this bit is 1, the auxiliary synthesizer is in integer-N mode. NOTE: There are no special power-up sequences required for the CX72302. • Multiplexer Output Selection = 3-bit value that selects which internal signal is output to the Mux_out pin. The following internal signals are available on this pin: − Reference Oscillator, Fref − Main or auxiliary divided reference (post reference frequency main or auxiliary dividers), Fref_main or Fref_aux − Main or auxiliary phase detector frequency (post main and auxiliary frequency dividers), Fpd_main or Fpd_aux − Serial data out, for loop-back and test purposes Refer to Table 4 for more information. • Mux_out Pin Three-State Enable = 1-bit value to three-state the Mux_out pin. When this bit is 0, the Mux_out pin is enabled. When this bit is 1, the Mux_out pin is three-stated. The Modulation Control Register is used to configure the modulation unit of the main synthesizer The modulation unit adds or subtracts a frequency offset to the selected center frequency at which the main synthesizer operates. The size of the modulation data sample, controlled by the duration of the CS signal, can be from 2 to 12 bits wide, to provide from 4 to 4096 selectable frequency offset steps. The modulation data magnitude offset selects the magnitude multiplier for the modulation data and can be from 0 to 8. As shown in Figure14, the values to be loaded are: • Modulation Data Magnitude Offset = 4-bit value that indicates the magnitude multiplier (m) for the modulation data samples. Valid values range from 0 to 13, effectively providing a 2m multiplication of the modulation data sample. • Modulation Data Input Select = 1-bit value that indicates the pin on which modulation data samples are serially input when the CS signal is between 2 and 12 bits long. When this bit is 0, modulation data samples are to be presented on the Data pin. When this bit is 1, modulation data samples are to be presented on the Mod_in pin. • Modulation Address Disable = 1-bit value that indicates the presence of the address as modulation data samples are presented on either the Mod_in or Data pins. When this bit is 0, the address is presented with the modulation data samples (i.e., all transfers are 16 bits long). When this bit is 1, no address is presented with the modulation data samples (i.e., all transfers are 2 to 12 bits long). Table 4. Multiplexer Output Multiplexer Output Select (Bit 8) 0 0 0 0 1 1 1 Multiplexer Output Select (Bit 7) 0 0 1 1 0 0 1 Multiplexer Output Select (Bit 6) 0 1 0 1 0 1 0 Multiplexer Output (Mux_out) Reference Oscillator Auxiliary Reference Frequency (Fref_aux) Main Reference Frequency (Fref_main) Auxiliary Phase Detector Frequency (Fpd_aux) Main Phase Detector Frequency (Fpd_main) Serial data out Serial Interface Register test output Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 101216G • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • July 22, 2004 13 DATA SHEET • CX72302 A3 1 A2 A1 0 0 A0 11 0 X 10 X 9 8 7 6 5 4 3 0 2 0 1 0 0 0 Reserved Bits Modulation Data Magnitude Offset Modulation Data Input Select Modulation Address Disable C1425 Figure 14. Modulation Control Register (Write Only) A3 1 A2 A1 0 0 A0 11 1 MSB 10 9 8 7 6 5 4 3 2 1 0 LSB Modulation Data Bits C1426 Figure 15. Modulation Data Register (Write Only) The Modulation Data Register is used to load the modulation data samples to the modulation unit. This value is transferred to the modulation unit on the falling edge of Fpd_main where it is passed to the main ∆Σ modulator at the selected magnitude offset on the next falling edge of Fpd_main. Modulation Data Register values are 2's complement format. As shown in Figure 15, the value to be loaded is: • Modulation Data Bits = Modulation data samples that represent the desired instantaneous frequency offset to the selected main synthesizer frequency (selected channel) before being affected by the modulation data magnitude offset. Signal pin assignments and functional pin descriptions are specified in Table 5. The absolute maximum ratings of the CX72302 are provided in Table 6. The recommended operating conditions are specified in Table 7 and electrical specifications are provided in Table 8. Figure 16 provides a schematic diagram for the CX72302. Figure 17 shows the package dimensions for the 28-pin EP-TSSOP and Figure 18 provides the tape and reel dimensions. Electrostatic Discharge (ESD) Sensitivity The CX72302 is a static-sensitive electronic device. Do not operate or store near strong electrostatic fields. Take proper ESD precautions. Electrical and Mechanical Specifications The CX72302 is supplied as a 28-pin EP-TSSOP. The exposed pad is located on the bottom side of the package and must be connected to ground for proper operation. The exposed pad should be soldered directly to the circuit board. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 14 July 22, 2004 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 101216G DATA SHEET • CX72302 Table 5. CX72302 Signal Descriptions Pin # 1 2 3 Pin Name Clock Mod_in Mux_out Type Digital input Digital input Digital output Description Clock signal pin. When CS is low, the register address and data are shifted in address bits first on the Data pin on the rising edge of Clock. Alternate serial modulation data input pin. Address bits are followed by data bits. Internal multiplexer output. Selects from oscillator frequency, main or auxiliary reference frequency, main or auxiliary divided VCO frequency, serial data out, or testability signals. This pin can be three-stated from the general synthesizer registers. Substrate isolation. Connect to ground. Emitter Coupled Logic (ECL)/Current Mode Logic (CML) ground. ECL/CML 3 V. Removing power safely powers down the associated divider chain and charge pump. Main VCO differential input. Main VCO complimentary differential input. Programmable output pin. Indicates main phase detector out-of-lock as an active low pulsing open collector output (high impedance when lock is detected), or helps the loop filter steer the main VCO. This pin is configured from the general synthesizer registers. Main charge pump 3 to 5 V. Removing power safely powers down the associated divider chain and charge pump. Main charge pump output. The gain of the main charge pump phase detector can be controlled from the general synthesizer registers. Main charge pump ground. Reference crystal AC ground or external oscillator differential input. Reference crystal input or external oscillator differential input. Reference crystal output or no connect. Crystal oscillator ECL/CML 3 V. Crystal oscillator ground. Programmable output pin. Indicates auxiliary phase detector out-of-lock as an active low pulsing open collector output (high impedance when lock is detected), or helps the loop filter steer the auxiliary VCO. This pin is configured from the general synthesizer registers. Auxiliary charge pump 3 to 5 V. Removing power safely powers down the associated divider chain and charge pump. Auxiliary charge pump output. The gain of the auxiliary charge pump phase detector can be controlled from the general synthesizer registers. Auxiliary charge pump ground. Auxiliary VCO complimentary differential input. Auxiliary VCO differential input. ECL/CML 3 V. Removing power safely powers down the associated divider chain and charge pump. Digital ground. Digital 3 V. Serial address and data input pin. Address bits are followed by data bits. Active low enable pin. Enables loading of address and data on the Data pin on the rising edge of Clock. When CS goes high, data is transferred to the register indicated by the address. Subsequent clock edges are ignored. 4 5 6 7 8 9 VSUBdigital GNDecl/cml (Note 1) VCCcml_main (Note 1) Fvco_main Fvco_main LD/PSmain – Power and ground Power and ground Input Input Analog output 10 11 12 13 14 15 16 17 18 VCCcp_main (Note 1) CPout_main GNDcp_main (Note 1) Xtalacgnd/OSC Xtalin/OSC Xtalout/NC VCCxtal GNDxtal LD/PSaux Power and ground Analog output Power and ground Ground/input Input Input Power and ground Power and ground Analog output 19 20 21 22 23 24 25 26 27 28 VCCcp_aux (Note 1) CPout_aux GNDcp_aux (Note 1) Fvco_aux Fvco_aux VCCcml_aux (Note 1) GNDdigital (Note 1) VCCdigital (Note 1) Data CS Power and ground Analog output Power and ground Input Input Power and ground Power and ground Power and ground Digital input Digital input Note 1: Associated pairs of power and ground pins must be decoupled using 0.1 µF capacitors. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 101216G • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • July 22, 2004 15 DATA SHEET • CX72302 Table 6. Absolute Maximum Ratings Parameter Maximum analog RF supply voltage Maximum digital supply voltage Maximum charge pump supply voltage Storage temperature Operating temperature –65 –40 Min Max 3.6 3.6 5.25 +150 +85 Units VDC VDC VDC °C °C Note: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal values. Table 7. Recommended Operating Conditions Parameter Analog RF supplies Digital supply Charge pump supplies Operating temperature (TA) Min 2.7 2.7 2.7 –40 Max 3.3 3.3 5.0 +85 Units VDC VDC VDC °C Table 8. Electrical Characteristics (1 of 2) (VDD = 3 V, TA = 25 °C, unless otherwise noted) Parameter Power Consumption Total power consumption PTOTAL Charge pump currents of 200 µA. Both synthesizers fractional, FREF_MAIN = 20 MHz, FREF_AUX = 1 MHz Auxiliary synthesizer power down Power-down current Reference Oscillator Reference oscillator frequency Oscillator sensitivity (as a buffer) Frequency shift versus supply voltage VCOs Main synthesizer operating frequency Auxiliary synthesizer operating frequency RF input sensitivity Main fractional-N tuning step size Auxiliary fractional-N tuning step size FVCO_MAIN FVCO_AUX Symbol Test Conditions Min Typ Max Units 54 mW 39 10 (Note 1) mW µA ICC-PWDN FOSC VOSC FSHIFT_SUPPLY AC coupled, single-ended 2.7 V ≤ VXTAL ≤ 3.3 V 0.1 50 2.0 ±0.3 MHz Vpp ppm Sinusoidal, –40 °C to +85 °C Sinusoidal, –40 °C to +85 °C AC coupled 400 (Note 2) 100 (Note 3) 50 4 × FREF_MAIN/2 or FREF_MAIN/2 18 10 6100 1000 250 MHz MHz mVpeak Hz Hz VVCO ∆FSTEP_MAIN ∆FSTEP_AUX FREF_AUX/210 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 16 July 22, 2004 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 101216G DATA SHEET • CX72302 Table 8. Electrical Characteristics (2 of 2) (VDD = 3 V, TA = 25 °C, unless otherwise noted) Parameter Noise Phase noise floor Pnf Measured inside the loop bandwidth using 25 MHz reference frequency, –40 °C to +85 °C –128 + 20 Log (N) dBc/Hz Symbol Test Conditions Min Typ Max Units Phase Detectors and Charge Pumps Main phase detector frequency Auxiliary phase detector frequency Charge pump output source current Charge pump output sink current Charge pump accuracy Charge pump output voltage linearity range Charge pump current versus temperature Charge pump current versus voltage Digital Pins High level input voltage Low level input voltage High level output voltage Low level output voltage Timing – Serial Interface Clock frequency Data and CS set up time to Clock rising Data and CS hold time after Clock rising fCLOCK tSU tHOLD 3 0 100 MHz ns ns VIH VIL VOH VOL IOH = –2 mA IOL = +2 mA VDIGITAL –0.2 GND + 0.2 0.7 VDIGITAL 0.3 VDIGITAL V V V V FREF_MAIN FREf_AUX ICP-SOURCE ICP-SINK ICP-ACCURACY ICP vs VCP ICP vs T ICP vs VCP 0.5 V ≤ VCP ≤ (VCCCP – 0.5 V) VCP = 0.5 VCCCP –40 °C < T < +85 °C 0.5 V ≤ VCP ≤ (VCCCP – 0.5 V) GND + 400 –40 °C to +85 °C –40 °C to +85 °C VCP = 0.5 VCCCP VCP = 0.5 VCCCP 125 –125 ±20 VCCCP – 400 5 8 25 25 1000 –1000 MHz MHz µA µA % mV % % Note 1: A 5 V charge pump power supply (on pin 10 and/or pin 19) results in higher power-down leakage current. Note 2: The minimum synthesizer frequency is 48 x FOSC, where FOSC is the frequency at the Xtalin/OSC pin. Note 3: The minimum synthesizer frequency is 12 x FOSC, where FOSC is the frequency at the Xtalin/OSC pin. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 101216G • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • July 22, 2004 17 DATA SHEET • CX72302 2 3 4 A A 2 Mod_in Data VCCdigital GNDdigital VCCcml_aux Fvco_aux Fvco_aux GNDcp_aux A 27 3V C1 1 nF C2 1 nF A A 3 3V 4 VSUBdigital GNDecl/cml VCCcml_main Fvco_main Fvco_main LD/PSmain VCCcp_main CPout_main GNDcp_main Xtalacgnd/OSC GND Mux_out 25 24 23 C4 C6 A 26 5 C3 1 nF A 2 6 A VCC VCC Auxiliary VCO 4 A 3 Auxiliary VCO VT 3V C7 8 9 CPout_aux VCCcp_aux LD/PSaux GNDxtal VCCxtal Xtalout/NC 18 17 A 3 5 4 2 21 20 GND A Lock Detect Main Output A RFOUT RF Out Main J1 1 C5 7 22 R1 100 k Ω 3V 10 C11 1 nF 11 12 A A 3V 19 A C8 R3 R2 C9 A VCC 3 VCC 2 RFOUT 3V 16 15 C10 1 nF C12 A A VT 1 R4 R5 C14 C15 A A 29 Figure 16. CX72302 Application Schematic GND A 4 14 Xtalin/OSC 13 Main VCO Auxiliary Synthesizer Loop Filter C17 1 nF A A External Pad Connection to Ground C17 A C16 100 pF Y1 C19 3V R6 100 k Ω C18 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 3V 1 1 Clock CS 28 Lock Detect Auxiliary Output July 22, 2004 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 101216G Main Synthesizer Loop Filter 1 C1427 5 18 To Microprocessor RF Out Auxiliary J1 DATA SHEET • CX72302 0.25 +0.5/–0.6 0.65 BSC Pin 1 4.4 ± 0.10 6.40 BSC 9.70 BSC 5.50 Top View Exposed Pad Bottom View 1.10 0.90 ± 0.05 0.10 ± 0.05 0.60 ± 0.10 Side View All measurements are in millimeters C1428 Figure 17. CX72302 28-Pin EP-TSSOP Package Dimensions 4.00 ± 0.10 8.00 ± 0.10 Pin #1 1.50 ± 0.10 2.00 ± 0.05 1.75 ± 0.10 A A 7.50 ± 0.10 B 1.50 ± 0.25 3.96 1.10 8o Max 6.75 ± 0.10 1.60 ± 0.10 Notes: 1. 2. 3. 4. 0.318 ± 0.013 7o Max 9.95 ± 0.10 A B Carrier tape material: black conductive polycarbonate or polystyrene Cover tape material: transparent conductive PSA Cover tape size: 13.3 mm width All measurements are in millimeters C1430 Figure 18. CX72302 Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 101216G • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • July 22, 2004 16.00 +0.30/–0.10 B 3.00 19 DATA SHEET • CX72302 Ordering Information Model Name CX72302 Frequency Synthesizer CX72302-11 Manufacturing Part Number Evaluation Kit Part Number PH00-D122 Copyright © 2001, 2002, 2004, Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products. These materials are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials. Skyworks may make changes to its documentation, products, specifications and product descriptions at any time, without notice. Skyworks makes no commitment to update the information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from future changes to its documentation, products, specifications and product descriptions. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by or under this document. Except as may be provided in Skyworks Terms and Conditions of Sale for such products, Skyworks assumes no liability whatsoever in association with its documentation, products, specifications and product descriptions. THESE MATERIALS ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED OR OTHERWISE, RELATING TO SALE AND/OR USE OF SKYWORKS PRODUCTS INCLUDING WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. SKYWORKS FURTHER DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THESE MATERIALS WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. The following are trademarks of Skyworks Solutions, Inc.: Skyworks™, the Skyworks logo, and Breakthrough Simplicity™. Product names or services listed in this publication are for identification purposes only, and may be trademarks of Skyworks or other third parties. Third-party brands and names are the property of their respective owners. Additional information, posted at www.skyworksinc.com, is incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 20 July 22, 2004 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 101216G