ECG050B-PCB

ECG050 Product Features x DC – 4 GHz x +19 dBm P1dB at 1 GHz x +34 dBm OIP3 at 1 GHz x 19 dB Gain at 1 GHz The Communications Edge TM Product Information InGaP HBT Gain Block Product Description The ECG050 is a general-purpose buffer amplifier that offers high dynamic range in a low-cost surface-mount package. At 1000 MHz, the ECG050 typically provides 19 dB of gain, +34 dBm Output IP3, and +19 dBm P1dB. The ECG050 consists of Darlington pair amplifiers using the high reliability InGaP/GaAs HBT process technology and only requires DC-blocking capacitors, a bias resistor, and an inductive RF choke for operation. The device is ideal for wireless applications and is available in low-cost, surface-mountable plastic SOT-86 and SOT-89 packages. The ECG050 is also available in a lead-free/green/RoHScompliant SOT-89 package. All devices are 100% RF and DC tested. The broadband MMIC amplifier can be directly applied to various current and next generation wireless technologies such as GPRS, GSM, CDMA, and W-CDMA. In addition, the ECG050 will work for other various applications within the DC to 4 GHz frequency range such as CATV and fixed wireless. Functional Diagram GND 4 x 5.5 dB Noise Figure at 2 GHz x Available in SOT-86, SOT89 and lead-free / green SOT89 Package Styles x Internally matched to 50 : 1 RF IN 2 GND 3 RF OUT ECG050B / ECG050B-G GND 4 Applications x x x x x x Mobile Infrastructure CATV / DBS W-LAN / ISM RFID Defense / Homeland Security Fixed Wireless RF In 1 3 RF Out 2 GND ECG050C Specifications (1) Parameter Operational Bandwidth Test Frequency Gain Output P1dB Output IP3 (2) Test Frequency Gain Input Return Loss Output Return Loss Output P1dB Output IP3 (2) Noise Figure Device Voltage Device Current Typical Performance (3) Units MHz MHz dB dBm dBm MHz dB dB dB dBm dBm dB V mA Min DC Typ 1000 19 +19 +34 2000 17 19 15 +18.5 +31 5.4 5.0 70 Max 4000 Parameter Frequency S21 S11 S22 Output P1dB Output IP3 Noise Figure Units MHz dB dB dB dBm dBm dB 500 20 -17 -15 +18 +33 3.5 Typical 900 19.2 -18 -15 +19 +34 4 1900 17 -19 -15 +18.5 +31 5.4 ¡ ¡ 2140 16 -20 -15 +18.2 +30.5 3.8 System. 3. Test conditions: T = 25º C, Supply Voltage = +6 V, Device Voltage = +5.0V, Rbias = 14 , 50 4.2 5.2 ¡ ¡ 1. Test conditions unless otherwise noted: 25º C, Supply Voltage = +6 V, Rbias = 14 , 50 System. 2. 3OIP measured with two tones at an output power of +4 dBm/tone separated by 1 MHz. The suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule. Ordering Information Absolute Maximum Rating Parameter Operating Case Temperature Storage Temperature RF Input Power (continuous) Device Current Junction Temperature -40 to +85 qC -65 to +150 qC +12 dBm 150 mA +250 qC Part No. ECG050B ECG050B-G ECG050C ECG050B-PCB ECG050C-PCB Description (leaded SOT-89 Pkg) Rating InGaP HBT Gain Block InGaP HBT Gain Block (lead-free/green/RoHS-compliant SOT-89 Pkg) InGaP HBT Gain Block (SOT-86 Pkg) 700 –2400 MHz Fully Assembled Eval. Board 700 –2400 MHz Fully Assembled Eval. Board Specifications and information are subject to change without notice Operation of this device above any of these parameters may cause permanent damage. WJ Communications, Inc         Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: sales@wj.com W eb site: www.wj.com December 2004 ECG050 Frequency S21 S11 S22 Output P1dB Output IP3 Noise Figure The Communications Edge TM Product Information InGaP HBT Gain Block Typical Device RF Performance Supply Bias = +6 V, Rbias = 14 :, Icc = 70 mA 100 20.4 -17 -15 +18 +33 3.4 500 20 -17 -15 +18 +33 3.5 ¡ MHz dB dB dB dBm dBm dB 900 19.2 -18 -15 +19 +34 4 1900 17.2 -19 -15 +18.7 +31 5.4 ¡ 2140 16.7 -20 -15 +18.2 +30.5 5.8 2400 16.1 -20 -15 +17.8 +29 6 3500 14.2 -19 -14 +12.2 5800 10.3 -11 -7.5 1. Test conditions: T = 25º C, Supply Voltage = +6 V, Device Voltage = 5.0 V, Rbias = 14 , Icc = 70 mA typical, 50 System. 2. 3OIP measured with two tones at an output power of +4 dBm/tone separated by 1 MHz. The suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule. 3. Data is shown as device performance only. Actual implementation for the desired frequency band will be determined by external components shown in the application circuit. Gain vs. Frequency 22 20 Gain (dB) 18 16 14 12 10 0 1 2 3 4 5 6 Frequency (GHz) OIP3 vs. Frequency 40 35 30 25 25° C 20 500 1000 85° C -40° C 2500 3000 0 500 NF (dB) 6 S11, S22 (dB) 0 -5 -10 -15 -20 -25 0 1 S11, S22 vs. Frequency 200 160 Icc (mA) S22 120 25° C 80 40 0 2 3 4 Frequency (GHz) 5 6 0 1 Icc vs. Vde S11 2 3 Vde (V) 4 5 6 Noise Figure vs. Frequency 26 22 18 14 P1dB vs. Frequency 4 2 P1dB (dBm) OIP3 (dBm) 25° C 1000 1500 2000 10 500 1000 85° C -40° C 2500 3000 1500 2000 Frequency (MHz) Frequency (MHz) 1500 2000 Frequency (MHz) Specifications and information are subject to change without notice         WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: sales@wj.com W eb site: www.wj.com December 2004 ECG050 The Communications Edge TM Product Information InGaP HBT Gain Block Recommended Application Circuit Vcc Icc = 70 mA R4 Bias Resistor C4 Bypass Capacitor C3 0.018 µF L1 RF Choke RF IN ECG050 C1 Blocking Capacitor C2 Blocking Capacitor RF OUT ECG050B-PCB ECG050C-PCB Reference Designator L1 C1, C2, C4 50 820 nH .018 µF Recommended Component Values Frequency (MHz) 500 900 1900 2200 220 nH 68 nH 27 nH 22 nH 1000 pF 100 pF 68 pF 68 pF 2500 18 nH 56 pF 3500 15 nH 39 pF 1. The proper values for the components are dependent upon the intended frequency of operation. 2. The following values are contained on the evaluation board to achieve optimal broadband performance: Ref. Desig. L1 C1, C2 C3 C4 R4 Value / Type 39 nH wirewound inductor 56 pF chip capacitor 0.018 PF chip capacitor Do Not Place 14 : 1% tolerance Size 0603 0603 0603 0805 Recommended Bias Resistor Values Supply R1 value Size Voltage 6V 14.3 ohms 0805 7V 28.6 ohms 1210 8V 43 ohms 1210 9V 57 ohms 2010 10 V 71 ohms 2010 12 V 100 ohms 2512 The proper value for R1 is dependent upon the supply voltage and allows for bias stability over temperature. WJ recommends a minimum supply bias of +6 V. A 1% tolerance resistor is recommended. Specifications and information are subject to change without notice         WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: sales@wj.com W eb site: www.wj.com December 2004 ECG050 The Communications Edge TM Product Information InGaP HBT Gain Block ECG050B (SOT-89 Package) Mechanical Information This package may contain lead-bearing materials. The plating material on the leads is SnPb. Outline Drawing Product Marking The component will be marked with an “E050” designator with an alphanumeric lot code on the top surface of the package. Tape and reel specifications for this part are located on the website in the “Application Notes” section. MSL / ESD Rating ESD Rating: Value: Test: Standard: Class 1A Passes between 250 and 500V Human Body Model (HBM) JEDEC Standard JESD22-A114 ¢ MSL Rating: Level 3 at +235 C convection reflow Standard: JEDEC Standard J-STD-020 Mounting Config. Notes Land Pattern 1. Ground / thermal vias are critical for the proper performance of this device. Vias should use a .35mm (#80 / .0135” ) diameter drill and have a final plated thru diameter of .25 mm (.010” ). 2. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 3. Mounting screws can be added near the part to fasten the board to a heatsink. Ensure that the ground / thermal via region contacts the heatsink. 4. Do not put solder mask on the backside of the PC board in the region where the board contacts the heatsink. 5. RF trace width depends upon the PC board material and construction. 6. Use 1 oz. Copper minimum. 7. All dimensions are in millimeters (inches). Angles are in degrees. Specifications and information are subject to change without notice         WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: sales@wj.com W eb site: www.wj.com December 2004 ECG050 The Communications Edge TM Product Information InGaP HBT Gain Block This package is lead-free/Green/RoHS-compliant. It is compatible with both lead-free (maximum 260qC reflow temperature) and leaded (maximum 245qC reflow temperature) soldering processes. The plating material on the leads is NiPdAu. ECG050B-G (Green / Lead-free SOT-89 Package) Mechanical Information Outline Drawing Product Marking The component will be marked with an “ E050G” designator with an alphanumeric lot code on the top surface of the package. Tape and reel specifications for this part are located on the website in the “ Application Notes” section. MSL / ESD Rating ESD Rating: Value: Test: Standard: Class 1A Passes between 250 and 500V Human Body Model (HBM) JEDEC Standard JESD22-A114 ¢ Land Pattern MSL Rating: Level 3 at +260 C convection reflow Standard: JEDEC Standard J-STD-020 Mounting Config. Notes 1. Ground / thermal vias are critical for the proper performance of this device. Vias should use a .35mm (#80 / .0135” ) diameter drill and have a final plated thru diameter of .25 mm (.010” ). 2. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 3. Mounting screws can be added near the part to fasten the board to a heatsink. Ensure that the ground / thermal via region contacts the heatsink. 4. Do not put solder mask on the backside of the PC board in the region where the board contacts the heatsink. 5. RF trace width depends upon the PC board material and construction. 6. Use 1 oz. Copper minimum. 7. All dimensions are in millimeters (inches). Angles are in degrees. Specifications and information are subject to change without notice         WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: sales@wj.com W eb site: www.wj.com December 2004 ECG050 The Communications Edge TM Product Information InGaP HBT Gain Block ECG050C (SOT-86 Package) Mechanical Information Outline Drawing Product Marking The component will be marked with a twodigit numeric lot code followed by a “ V” designator on the top surface of the package. Tape and reel specifications for this part are located on the website in the “ Application Notes” section. MSL / ESD Rating ESD Rating: Value: Test: Standard: Class 1A Passes between 250 and 500V Human Body Model (HBM) JEDEC Standard JESD22-A114 ¢ MSL Rating: Level 1 at +235 C convection reflow Standard: JEDEC Standard J-STD-020 Land Pattern Mounting Config. Notes 1. Ground / thermal vias are critical for the proper performance of this device. Vias should use a .35mm (#80 / .0135” ) diameter drill and have a final plated thru diameter of .25 mm (.010” ). 2. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 3. Mounting screws can be added near the part to fasten the board to a heatsink. Ensure that the ground / thermal via region contacts the heatsink. 4. Do not put solder mask on the backside of the PC board in the region where the board contacts the heatsink. 5. RF trace width depends upon the PC board material and construction. 6. Use 1 oz. Copper minimum. 7. All dimensions are in millimeters (inches). Angles are in degrees. Specifications and information are subject to change without notice £ £ £ £ WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: sales@wj.com W eb site: www.wj.com December 2004 ECG050 Freq (MHz) S11 (dB) The Communications Edge TM Product Information InGaP HBT Gain Block Typical Device S-Parameters – ECG050B / ECG050B-G S-Parameters (Vdevice = +5 V, ICC = 70 mA, T = 25 C, calibrated to device leads) S11 (ang) 50 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 -24.67 -23.02 -20.62 -18.00 -15.55 -13.31 -12.32 -10.81 -9.44 -8.05 -6.55 -5.51 -4.48 -3.70 -46.71 -90.90 -120.26 -154.19 173.42 144.67 116.58 93.67 72.95 55.09 39.20 25.52 Typical Device S-Parameters – ECG050C S-Parameters (Vdevice = +5, ICC = 70 mA, T = 25 C, calibrated to device leads) Freq (MHz) S11 (dB) S11 (ang) 50 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 -20.98 -20.20 -19.34 -18.54 -18.87 -19.47 -20.32 -21.04 -18.70 -16.20 -12.95 -10.83 -8.87 1.45 -4.73 -18.92 -33.65 -50.53 -73.82 -97.64 -138.52 -173.90 159.57 137.68 123.87 110.42 Device S-parameters are available for download off of the website at: http://www.wj.com £ £ £ £ WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 ¢ S21 (dB) S21 (ang) S12 (dB) S12 (ang) S22 (dB) S22 (ang) 21.16 20.62 19.55 18.33 17.43 16.53 15.45 14.33 13.19 12.09 10.89 9.64 8.50 176.94 148.95 121.77 98.78 77.57 55.93 35.48 15.84 -3.31 -20.87 -38.22 -54.94 -70.62 -23.25 -22.86 -21.99 -20.82 -19.60 -18.78 -18.21 -17.75 -17.44 -17.20 -17.20 -17.33 -17.57 0.44 2.51 3.04 0.20 -6.65 -15.98 -25.37 -35.05 -45.26 -55.51 -66.45 -76.61 -87.04 -19.85 -17.88 -15.13 -12.53 -10.50 -8.97 -7.94 -7.23 -6.22 -5.47 -4.64 -4.04 -3.59 -5.11 -66.96 -106.94 -136.27 -164.08 169.04 142.85 121.33 101.54 83.50 67.48 51.93 38.34 ¢ S21 (dB) S21 (ang) S12 (dB) S12 (ang) S22 (dB) S22 (ang) 20.66 20.19 19.27 18.09 17.03 15.90 14.91 14.02 13.20 12.38 11.64 10.80 9.99 176.82 153.75 130.28 109.96 92.08 75.80 61.09 46.72 32.70 19.24 5.50 -8.36 -21.17 -22.87 -22.67 -22.24 -21.62 -20.77 -19.95 -19.08 -18.29 -17.51 -16.83 -16.30 -15.88 -15.56 0.51 4.30 8.25 10.86 12.09 11.53 9.94 6.69 2.82 -2.20 -7.81 -14.30 -20.60 -17.49 -18.13 -18.82 -19.01 -19.21 -18.26 -16.38 -14.83 -12.69 -11.23 -9.78 -8.58 -7.59 -2.70 -31.56 -58.47 -89.85 -122.43 -148.97 -175.04 166.20 150.06 134.69 122.17 108.98 97.93 Specifications and information are subject to change without notice e-mail: sales@wj.com W eb site: www.wj.com December 2004