GS1K

RS GS1A THRU GS1M SURFACE MOUNT STANDARD RECOVERY RECTIFIER VOLTAGE - 50 TO 1000 VOLTS CURRENT - 1.0 AMPERE FEATURES For surface mount applications Glass passivated junction Low profile package Built-in strain relief Easy pick and place Low forward voltage drop Plastic package has Underwriters Laboratory Flammability Classification 94V-0 High temperature soldering: 250oC/10 seconds at terminals B C A D J H G E SMA / DO-214AC Dim Min Max A 2.29 2.92 B 4.00 4.60 1.25 1.65 C 0.152 0.305 D 4.80 5.59 E 0.051 0.203 G 0.76 1.52 H 2.00 2.62 J All Dimensions in mm MECHANICAL DATA Case: JEDEC DO-214AC molded plastic Terminals: Solder plated, solderable per MIL-STD-202, method 208 Polarity: Color band denotes cathode end Standard Package: 12mm tape (EIA STD EIA-481) Weight: 0.002 ounce, 0.064 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25oC ambient temperature unless otherwise specified Single phase half wave 60 Hz, resistive or inductive load For capacitive load, derate current by 20% Maximum Repetitive Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at TL = 100oC Peak Forward Surge Current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum Instantaneous Forward Voltage at 1.0A Maximum DC Reverse Current at Rated DC Blocking Voltage TA = 25oC TA = 125oC IR CJ R R JA JL SYMBOL GS1A GS1B GS1D GS1G GS1J GS1K GS1M UNITS 50 100 200 400 600 VRRM 800 1000 Volts 35 70 140 280 420 VRMS 560 700 Volts 50 100 200 400 600 800 1000 Volts VDC I(AV) 1.0 Amps IFSM VF 30 1.1 5 50 12 75 30 -55 to +150 Amps Volts A pF o Typical Junction Capacitance (NOTE 1) Maximum Thermal Resistance (NOTE 2) Operating and Storage Temperature Range C/W o TJ, TSTG C NOTES: 1. Measured at 1.0 MHz and applied reverse voltage of 4.0 volts 2. P.C.B. mounted on 0.2 x 0.2" (5.0 x 5.0mm) copper pad areas RS GS1A THRU GS1M 30 AVERAGE FORWARD CURRENT (AMPS) P.C.B. MOUNTED ON 0.2 x 0.2" (5.0 x 5.0mm) COPPER PAD AREAS 1.0 PEAK FORWARD SURGE CURRENT (AMPS) 1.5 25 8.3 MS SINGLE HALF SINE-WAVE JEDEC METHOD 20 0.5 SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD 15 0 0 25 50 75 100 125 O 10 150 175 LEAD TEMPERATURE ( C) 5 Figure 1. Typical Forward Current Derating Curve 0 1 10 100 NUMBER OF CYCLES AT 60Hz Figure 2. Maximum Non-Repetitive Peak Forward Surge Current INSTANTANEOUS FORWARD CURRENT (AMPS) 100 100 TJ = 25OC f = 1.0MHz Vsig = 50mVp-p 10 JUNCTION CAPACITANCE (pF) 1 TJ = 25OC PULSE WIDTH = 300 1% DUTY CYCLE 10 S 0.1 1 0.01 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0.1 1.0 10 100 REVERSE VOLTAGE (VOLTS) INSTANTANEOUS FORWARD VOLT AGE (VOLTS) Figure 4.Typical Junction Capacitance Figure 3. Typical Instantaneous Forward Characteristics 10 INSTANTANEOUS REVERSE CURRENT A) TJ = 125 OC 1 1000 THERMAL IMPEDANCE (OC / W) TJ = 100 OC 0.1 100 10 UNITS MOUNTED ON 0.2x0.2" (5.0x5.0mm) x 0.5mil. INCHES (0.013mm) THICK COPPER LAND AREAS TJ = 25 OC 0.01 1 0.01 0.1 1.0 10 100 0.001 HEATING TIME (SEC) 0 20 40 60 80 100 Figure 5.Transient Thermal Impedance PERCENT OF PEAK REVERSE VOLT AGE(%) Figure 6.Typical Reverse Characteristics