IRM8602

EVERLIGHT ELECTRONICS CO., LTD. MODEL NO: Device Number: DMO-860-002 REV: IRM-8602 ECN: Page: 2.1 1/10 ■ PACKAGE DIMENSIONS： OFFICE: NO 25,Lane 76,Chung Yang Rd, Sec.3 Tucheng, Taipei 236, Taiwan, R.O.C. TEL FAX : 886-2-2267-2000,2266-9936 ( 22 Lines ) : 886-2-2267-6189 http://www.everlight.com EVERLIGHT ELECTRONICS CO., LTD. MODEL NO: Device Number: DMO-860-002 REV: IRM-8602 ECN: Page: 2.1 2/10 ■ NOTES： 1. This drawing measure is a standard value. All dimensions are in millimeter. 2. In case of designation is tolerance ± 0.3mm. 3. Lead spacing is measured where the lead emerge from the package. 4. Protruded resin under flange 1.0mm Max. 5. Lens color: Black. 6. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 7. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don't reproduce or cause anyone to reproduce them without EVERLIGHT consent. 8. When using this produce, please observe the absolute maximum ratings and the instructions for use outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. EVERLIGHT ELECTRONICS CO., LTD. MODEL NO: Device Number: DMO-860-002 REV: IRM-8602 ECN: Page: 2.1 3/10 ■ Description： The device is a miniature type infrared remote control system receiver which has been developed and designed by utilizing the most updated IC technology. The PIN diode and preamplifier are assembled on lead frame, the epoxy package is designed as an IR filter. The demodulated output signal can directly be decoded by a microprocessor. ■ Feature： High protection ability to EMI and metal case can be customized. Mold type and metal case type to meet the design of front panel. Elliptic lens to improve the characteristic against Line-up for various center carrier frequencies. Low voltage and low power consumption. High immunity against ambient light. Photodiode with integrated circuit. TTL and CMOS compatibility. Long reception distance. 10. High sensitivity. 1. 2. 3. 4. 5. 6. 7. 8. 9. ■ Application： 1. Optical switch 2. Light detecting portion of remote control • AV instruments such as Audio, TV, VCR, CD, MD, etc. • Home appliances such as Air-conditioner, Fan , etc. • The other equipments with wireless remote control. • CATV set top boxes • Multi-media Equipment EVERLIGHT ELECTRONICS CO., LTD. MODEL NO: Device Number: DMO-860-002 REV: IRM-8602 ECN: Page: 2.1 4/10 ■ Absolute maximum ratings： Parameter Symbol Ratings Supply Voltage Vcc 0~6 -20〜+75 Operating Temperature Topr -20〜+85 Storage Temperature Tstg Soldering Temperature Tsol 260 Unit V ℃ ℃ ℃ (Ta=25℃) Notice 4mm from mold body less than 5 seconds ■ Electro Optical Characteristics： Parameter TYP Symbol MIN Vcc 4.5 5 Supply Voltage Icc Supply Current B.P.F Center Frequency Peak Wavelength Transmission Distance Half Angle (Horizontal) Half Angle (Vertical) High Level Pulse Width Low Level Pulse Width High Level Output Voltage Low Level Output Voltage MAX 5.5 3 800 800 0.5 Unit V mA KHz nm m deg deg µs µs V V (Ta=25℃) Condition DC voltage No signal input fo λp L0 L45 θh θv TH TL VH VL 8 4 400 400 4.5 - 38 940 45 35 0.2 At the ray axis *1 At the ray axis *2 *1:The ray receiving surface at a vertex and relation to the ray axis in the range of φ= 0° and φ=45°. *2:A range from 30cm to the arrival distance. Average value of 50 pulses. EVERLIGHT ELECTRONICS CO., LTD. MODEL NO: Device Number: DMO-860-002 REV: IRM-8602 ECN: Page: 2.1 5/10 ■ TEST METHOD： The specified electro-optical characteristics is satisfied under the following Conditions at the controllable distance. Measurement place A place that is nothing of extreme light reflected in the room. External light Project the light of ordinary white fluorescent lamps which are not high Frequency lamps and must be less then 10 Lux at the module surface. (Ee≦10Lux) Standard transmitter A transmitter whose output is so adjusted as to Vo=400mVp-p and the output Wave form shown in Fig.-1.According to the measurement method shown in Fig.-2 the standard transmitter is specified. However , the infrared photodiode to be used for the transmitter should be λp=940nm,∆λ=50nm. Also, photodiode is used of PD438B (VR=5V). (Standard light / Light source temperature 2856°K). Measuring system According to the measuring system shown in Fig.-3 EVERLIGHT ELECTRONICS CO., LTD. MODEL NO: Device Number: DMO-860-002 IRM-8602 ECN: REV: Page: 2.1 6/10 ■ Block Diagram： ■ Application Circuit： RC Filter should be connected closely between Vcc pin and GND pin. EVERLIGHT ELECTRONICS CO., LTD. MODEL NO: Device Number: DMO-860-002 REV: IRM-8602 ECN: Page: 2.1 7/10 Fig.-1 Transmitter Wave Form Carrier frequency is adjusted to center frequency of each product. D.U.T output Pulse IR TANSMITTER OUTPUT WAVE FORM OUTPUT PULSE OF DEVICE Duty=0.5 Fig.-2 Measuring Method 20cm 10k +5.0± 0.1V 10uF Fig.-3 Measuring System L: Transmission Distance Vcc θ θ OUT D.U.T GND Standard Transmitter 100k Vout Standard Transmitter Vout Oscilloscope θ: Angle Of Horizontal & Vertical Direction EVERLIGHT ELECTRONICS CO., LTD. MODEL NO: Device Number: DMO-860-002 REV: IRM-8602 ECN: Page: 2.1 8/10 ■ TYPICAL ELECTRICAL/OPTICAL/CHARACTERISTICS CURVES Fig.-4 Relative Spectral Sensitivity vs. Wavelength Fig.-5 Relative Transmission Distance vs. Direction θ Fig.-6 Output Pulse Length vs. Arrival Distance Fig.-7 Arrival Distance vs. Supply Voltage Fig.-8 Relative Transmission Distance vs. Center Carrier Frequency Fig.-9 Arrival Distance vs. Ambient Temperature EVERLIGHT ELECTRONICS CO., LTD. MODEL NO: Device Number: DMO-860-002 REV: IRM-8602 ECN: Page: 2.1 9/10 ■ Reliability test item and condition： The reliability of products shall be satisfied with items listed below. Confidence level: 90% LTPD: 10% Test Items Operation life Test Conditions Failure Judgement Criteria Samples(n) Defective(c) n=22,c=0 L0≦ L× 0.8 L45≦ L× 0.8 n=22,c=0 Vcc=5V,Ta:25℃ 1000hrs 1 cycle -40℃ +25℃ +85℃ Temperature (30min)(5min)(30min) cycle 50 cycle test -10℃ to +100℃ Thermal shock (5min) (10sec) (5min) 50 cycle test High temperature Temp: +85℃ storage 1000hrs Low temperature Temp: -40℃ storage 1000hrs High temperature Ta: 85℃,RH:85% High humidity 1000hrs Solder heat Solderability Temp: 260± 5℃ 5sec 4mm Form the bottom of the package. Temp: 230± 5℃ 5sec n=22,c=0 n=22,c=0 L: Lower specification limit n=22,c=0 n=22,c=0 n=22,c=0 More than 90% of Lead to be covered n=22,c=0 4mm Form the bottom of the package. by soldering EVERLIGHT ELECTRONICS CO., LTD. MODEL NO: Device Number: DMO-860-002 REV: IRM-8602 ECN: Page: 2.1 10/10 ■ Packing Specifications 1.Bag 4.5 3.5 4.0 5.5 15± 0.5 Label 19± 0.5 22 EVERLIGHT Opto-electronic,Compoments 2.Box 15 Label 3.Carton 33 E V E R L I G H T 24 9 Label 48 Label UNIT：cm CPN : Customer’s Production Number P/N : Production Number QTY : Packing Quantity CAT : Ranks HUE : Peak Wavelength REF : Reference LOT NO : Lot Number MADE IN TAIWAN : Production place Packing Quantity Specification 1. 250 Pcs/1Bag，6 Bags/1Box 2. 10 Boxes/1Carton