L1084S5

NIKO-SEM 5A Adjustable Low Dropout Linear Regulator (LDO) FEATURES L1084S5 TO-263 GENERAL DESCRIPTION The L1084 is a positive and low dropout three-terminal voltage regulator with 5A output current capability. This device is designed for use in low voltage applications that offers lower dropout voltage and faster transient response. This device is fully protected against over current faults, over temperature operation, reversed input polarity, reversed lead insertion, transient voltage spike …etc. On-Chips trimming the reference voltage to 1% and features the low dropout of maximum 1.45 volts. The L1084 Series regulators are available in the popular industry standard TO-263 packages. Very easy to use, it requires only two external resistors to set the output voltage Low dropout voltage: 1.2V typical at up to 5A Low ground current Fast transient response Current & thermal limiting Line regulation: 0.5% typical Load regulation: 0.5% typical TO-263 packages APPLICATIONS High current microprocessor supplies Low voltage logic supply Powering VGA & sound card Portable instrumentation Constant current regulator Post regulator for switching power supply TYPICAL APPLICATION Vin 5 L1084X5 IN ADJ OUT 3 Vout Vref Cin 10uF 2 + R1 + Cout 10uF Iadj R2 Vo = Vref (1+R2/R1) + Iadj x R2 1. Cin needed if device is far from filter capacitors. 2. Cout required for stability. - Basic Adjustable Regulator Circuit - 1 Rev. 1.0 MAR NIKO-SEM 5A Adjustable Low Dropout Linear Regulator (LDO) L1084S5 TO-263 ABSOLUTE MAXIMUM RATINGS Maximum Supply Voltage Power Dissipation Thermal Resistance Junction to Case, θJC Thermal Resistance Junction to Ambient, θJA TO-263 7V Internally Limited 2.5 °C/W Operating Junction Temperature Range Storage Temperature Range Lead Temperature (Soldering, 10 Seconds) 0 to 125 °C -40 to 150 °C 260 °C 60 °C/W ELECTRICAL CHARACTERISTICS (Unless otherwise specified, TA = 25 °C.) Parameter Reference Voltage Dropout Voltage Line Regulation Load Regulation Minimum Load Current Symbol VREF Test Conditions VIN = 5V, IOUT = 10mA Typical 1.25V 1.2V 0.5% 0.5% 10mA 55µA 7.5A 0.003% of VOUT 72dB Limits 1.23VMin 1.27VMax 1.45V 2% 2.5% 100µA 5.0A (Min) VD ΔVREF = 1%, IOUT = 5A REG(LINE) (VOUT + 1.5V) ≤ VIN ≤ 7V, IOUT = 10mA REG(LOAD) (VIN -VOUT) = 3V, 10mA ≤ IOUT ≤ 5A IO IADJ ICL VN RA f = 120Hz, CADJ = 22µF for ADJ pin, VIN = 5V, IOUT = 5A 1.5V ≤ (VIN -VOUT) ≤ 5.75V VIN - VOUT = 2V Adjust Pin Current Current Limit RMS Output Noise Ripple Rejection Ratio 60dB (Min) DEVICE SELECTION GUIDE Device Package Marking L1084S5 TO-263 (5-Lead) L1084S5 2 Rev. 1.0 MAR NIKO-SEM 5A Adjustable Low Dropout Linear Regulator (LDO) L1084S5 TO-263 PIN CONFIGURATIONS Pin # 1 2 3 4 5 Function NC Adjust Output NC Input Note: TAB is Output Pin 3 Rev. 1.0 MAR NIKO-SEM 5A Adjustable Low Dropout Linear Regulator (LDO) L1084S5 TO-263 TO-263 (D2PAK, 5-Lead) MECHANICAL DATA mm Dimension A B C D E F G 0.3 -0.102 8.5 9 Min. 14.5 4.2 1.20 2.8 0.4 0.5 0.203 9.5 Typ. 15 Max. 15.8 4.7 1.35 Dimension H I J K L M N 0.7 1.57 Min. 1.0 9.8 6.5 1.5 0.85 1.7 1.0 1.83 mm Typ. 1.5 Max. 1.8 10.3 4 Rev. 1.0 MAR