MX98224EC

PRELIMINARY MX98224EC 24-port Dual-Speed Ethernet Switch Controller FEATURES l l l l l l l l Single chip 24-port 10/100M wire speed Ethernet switching controller with all memory embedded Integration of 24-port dual speed, full/half duplex capable Media Access Controllers (MACs) with RMII interfaces Support IEEE 802.3x compliant flow control for FDX and back-pressure flow control for HDX Auto-negotiation through MDC/MDIO Support source/destination MAC address lookup and aging within built-in storage of 8K MAC address (4K entries each entry table) Self address learning, forwarding, and filtering schemes Store-and-Forward switching operation 12-group port base VLAN with port overlapping l l l l l l l l l l l IEEE 802.1q CoS and two priority queues support based on port, tagging, and TOS configurations Address table and PHY register access allowed through CPU processor Dynamic buffer management No head-of-line blocking system support Power on self diagnostic Serial EEPROM (93C46) interface for autoconfiguration Broadcast storm prevention Serial CPU interface support for system configuration required Three alter/self-diagnostic LED interface CMOS, 1.8/3.3V I/O tolerance 208 PQFP package GENERAL DESCRIPTION MX98224EC is a stand-alone 10/100M Ethernet switch controller with SRAM embedded which saves 2-3 extra 64KX64 SRAM cost. Any standalone desktop or enterprising Ethernet switches can be achieved by simply combining MX98224EC and quad/octal physical devices. All 24 ports are full duplex capable to provide dedicated 20/200M bandwidth connections each port. MX98224EC basically supports store-and-forward switching scheme with two address entry tables, 4K size each. The function modules integrated in controller include 24-port half/full-duplex compatible media access controller with RMII interface, address resolution logic (ARL) for address learning, filtering, recognition, priority queue manager, port base VLAN. It fully complies with IEEE Std. 802.3/802.3u/802.1q specifications and supports MDC/MDIO interface for physical layer management with industrial standard physical devices. The switch architecture adopting dynamic buffer management shared by 24 ports can reach full-line speed of high performance application. To save system cost, single 50Mhz clock is for RMII and system requirement. MX98224EC proceeds in advanced foundry and smaller package which consumes lower power dissipation. The smart features with low power CPU or EEPROM are for system configuration and ALR access required. Also, it emphasizes at Class of Service (CoS) which extracts various packet types in appropriate forwarding scheme. Now, Voice over IP (VoIP) is applied the feature for cutting voice packet latency and promise the quality of service. In addition, port-base VLAN is another valuable feature for the switches. MX98224EC offers 12 groups with port overlapping allowed. The feature can add on more security and data flow in the same switch with different groups should get connection through router. The powerful switching architecture and robust design can easily reach high performance, non-blocking data flow. Head-of-line blocking prevents switch performance, and operation defective from other port impacts. The switch architecture provides a clean port independent operation. It guarantees port transmission or receive is not affected by other ports. Moreover, user can discard broadcast packets regarding the threshold of system overload. This prevents potential broadcast storming from abnormal events. After buffer fullness drops in the safe margin, the switch controller jumps into flow control state to allow physical ports work as normal condition. MX98224EC provides self on test as soon as power on or reset. It will detect all buffer memory and address table and others. If defective, LED is automatically on. Several LEDs are defined in switch controller like status of broadcast storm, packet loss, and buffer full. P/N:PM0782 1 REV. 0.2, Apr, 18, 2001 MX98224EC ECS ESK EDI EDO LEDA LEDB LEDC INCLK IODATA CPUSEL PRITY0 PRITY23 ENPRITY MDC MDIO CRSDV_P RXD_P[1:0] TXEN_P TXD_P[1:0] CPU I/F EEPROM I/F Registers LED I/F Pin Setting Unicast Link List Multicast Link List 10/100M Ethernet MAC Empty Table Buffer Memory MDC/MDIO I/F CLK RESET Address Resolution Logic 4K Address Table Figure 1. MX98224EC Functional Block Diagram P/N:PM0782 2 REV. 0.2, Apr, 18, 2001 MX98224EC RS-232 CPU MXIC 24-port Switch EEPROM Octal PHY Octal PHY Octal PHY Transformer Transformer Transformer Figure 2. MX98224EC System Block Diagram Optional Components P/N:PM0782 3 REV. 0.2, Apr, 18, 2001 MX98224EC TXD_22[1] TXD_22[0] TXEN_22 CRSDV_22 RXD_22[0] RXD_22[1] TXD_23[1] TXD_23[0] TXEN_23 CRSDV_23 RXD_23[0] RXD_23[1] Vcc GND PRITY23 PRITY22 PRITY21 PRITY20 PRITY19 PRITY18 Vdd GND PRITY17 PRITY16 PRITY15 PRITY14 PRITY13 PRITY12 PRITY11 PRITY10 PRITY9 PRITY8 Vcc GND PRITY7 PRITY6 PRITY5 PRITY4 PRITY3 PRITY2 PRITY1 PRITY0 ENPRITY Vdd GND LEDC ENCPU/LEDB ENROM/LEDA ECS/CPUSEL ESK/OUTCLK EDI/IODATA EDO/INCLK 207 208 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 61 60 59 58 57 56 55 54 65 64 63 205 202 203 198 199 200 195 196 187 188 189 190 191 192 178 179 180 181 182 183 184 174 171 172 166 167 159 160 161 162 163 TXD_0[1] TXD_0[0] TXEN_0 CRSDV_0 RXD_0[0] RXD_0[1] TXD_1[1] TXD_1[0] TXEN_1 CRSDV_1 RXD_1[0] RXD_1[1] TXD_2[1] TXD_2[0] TXEN_2 Vdd GND CRSDV_2 RXD_2[0] RXD_2[1] TXD_3[1] TXD_3[0] TXEN_3 CRSDV_3 RXD_3[0] RXD_3[1] TXD_4[1] TXD_4[0] TXEN_4 CRSDV_4 RXD_4[0] RXD_4[1] Vcc GND TXD_5[1] TXD_5[0] TXEN_5 CRSDV_5 RXD_5[0] RXD_5[1] TXD_6[1] TXD_6[0] TXEN_6 CRSDV_6 RXD_6[0] RXD_6[1] Vdd GND TXD_7[1] TXD_7[0] TXEN_7 CRSDV_7 MX98224EC 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 RXD_21[1] RXD_21[0] CRSDV_21 TXEN_21 TXD_21[0] TXD_21[1] RESET# RXD_20[1] MDIO MDC GND Vdd RXD_20[0] CRSDV_20 TXEN_20 TXD_20[0] TXD_20[1] RXD_19[1] RXD_19[0] CRSDV_19 TXEN_19 GND Vcc TXD_19[0] TXD_19[1] RXD_18[1] RXD_18[0] CRSDV_18 TXEN_18 TXD_18[0] TXD_18[1] RXD_17[1] RXD_17[0] CRSDV_17 TXEN_17 GND Vdd TXD_17[0] TXD_17[1] RXD_16[1] RXD_16[0] CRSDV_16 TXEN_16 TXD_16[0] TXD_16[1] RXD_15[1] RXD_15[0] CRSDV_15 TXEN_15 TXD_15[0] TXD_15[1] RXD_14[1] Figure 3. MX98224EC Pin Diagram Top View 72 71 70 69 68 67 80 79 78 77 76 75 74 88 87 86 85 84 83 RXD_14[0] CRSDV_14 TXEN_14 TXD_14[0] TXD_14[1] RXD_13[1] RXD_13[0] GND Vcc CRSDV_13 TXEN_13 TXD_13[0] TXD_13[1] RXD_12[1] RXD_12[0] CRSDV_12 TXEN_12 TXD_12[0] GND Vdd TXD_12[1] RXD_11[1] RXD_11[0] CRSDV_11 CLK TXEN_11 TXD_11[0] TXD_11[1] RXD_10[1] GND Vcc RXD_10[0] CRSDV_10 TXEN_10 TXD_10[0] TXD_10[1] RXD_9[1] RXD_9[0] CRSDV_9 TXEN_9 TXD_9[0] GND Vdd TXD_9[1] RXD_8[1] RXD_8[0] CRSDV_8 TXEN_8 TXD_8[0] TXD_8[1] RXD_7[1] RXD_7[0] P/N:PM0782 4 REV. 0.2, Apr, 18, 2001 MX98224EC PIN DESCRIPTION 10/100Mbps RMII INTERFACE PIN# 4 10 18 24 30 38 44 52 58 66 72 81 89 95 103 109 115 123 129 137 143 154 160 166 6, 5 12, 11 20, 19 26, 25 32, 31 40, 39 46, 45 54, 53 60, 59 68, 67 76, 73 83, 82 91, 90 99, 98 105, 104 111, 110 117, 116 125, 124 131, 130 139, 138 149, 144 156, 155 162, 161 168, 167 PIN NAME CRSDV_0 CRSDV_1 CRSDV_2 CRSDV_3 CRSDV_4 CRSDV_5 CRSDV_6 CRSDV_7 CRSDV_8 CRSDV_9 CRSDV_10 CRSDV_11 CRSDV_12 CRSDV_13 CRSDV_14 CRSDV_15 CRSDV_16 CRSDV_17 CRSDV_18 CRSDV_19 CRSDV_20 CRSDV_21 CRSDV_22 CRSDV_23 RXD_0[1:0] RXD_1[1:0] RXD_2[1:0] RXD_3[1:0] RXD_4[1:0] RXD_5[1:0] RXD_6[1:0] RXD_7[1:0] RXD_8[1:0] RXD_9[1:0] RXD_10[1:0] RXD_11[1:0] RXD_12[1:0] RXD_13[1:0] RXD_14[1:0] RXD_15[1:0] RXD_16[1:0] RXD_17[1:0] RXD_18[1:0] RXD_19[1:0] RXD_20[1:0] RXD_21[1:0] RXD_22[1:0] RXD_23[1:0] I/O I DESCRIPTION Carrier Sense/Receive Data Valid Active high, indicate receive medium is non-idle. CRSDV is asserted asynchronously with respect to CLK. I Receive Data From Port 0 to Port 23, synchronous to CLK and RXD[1] is MSB. While CRSDV is deasserted, RXD[1:0] is “00”. P/N:PM0782 5 REV. 0.2, Apr, 18, 2001 MX98224EC 3 9 15 23 29 37 43 51 57 65 71 79 88 94 102 108 114 122 128 136 142 153 159 165 1, 2 7, 8 13, 14 21, 22 27, 28 35, 36 41, 42 49, 50 55, 56 61, 64 69, 70 77, 78 84, 87 92, 93 100, 101 106, 107 112, 113 118, 119 126, 127 132, 133 140, 141 151, 152 157, 158 163, 164 80 Subtotal TXEN_0 TXEN_1 TXEN_2 TXEN_3 TXEN_4 TXEN_5 TXEN_6 TXEN_7 TXEN_8 TXEN_9 TXEN_10 TXEN_11 TXEN_12 TXEN_13 TXEN_14 TXEN_15 TXEN_16 TXEN_17 TXEN_18 TXEN_19 TXEN_20 TXEN_21 TXEN_22 TXEN_23 TXD_0[1:0] TXD_1[1:0] TXD_2[1:0] TXD_3[1:0] TXD_4[1:0] TXD_5[1:0] TXD_6[1:0] TXD_7[1:0] TXD_8[1:0] TXD_9[1:0] TXD_10[1:0] TXD_11[1:0] TXD_12[1:0] TXD_13[1:0] TXD_14[1:0] TXD_15[1:0] TXD_16[1:0] TXD_17[1:0] TXD_18[1:0] TXD_19[1:0] TXD_20[1:0] TXD_21[1:0] TXD_22[1:0] TXD_23[1:0] CLK O 4mA Transmit Enable Active high, assertion indicates the MAC is presenting di-bits on TXD[1:0] for transmission. TXEN is asserted synchronously with first nibble of preamable and remained asserted while all di-bits transmitted are presented on RMII. TXEN is negated prior to 1st CLK rising edge following the final di-bit of frame. O 4mA Transmit Data From Port 0 to Port 23, synchronous to CLK and TXD[1] is MSB. When TXEN is asserted, TXD[1:0] are accepted fro transmission. TXD[1:0] is “00” when TXEN is deasserted. I Reference Clock For RMII and system clock use. 50MHz. 145 P/N:PM0782 6 REV. 0.2, Apr, 18, 2001 MX98224EC EEPROM INTERFACE PIN# 204 PIN NAME ENROM I/O I DESCRIPTION EEPROM Enable Internally pull down. Default disable. Active high; indicated configuration data is auto-loaded from EEPROM after reset. Tying this pin to ground disables EEPROM interface and prevents autoconfiguration. EEPROM Chip Select Active high. EEPROM Clock 390KHz derived from system clock. EEPROM Data Input Output data to the corresponding EDI pin of EEPROM. EEPROM Data Output Input data to the corresponding EDO pin of EEPROM. 5 205 206 207 208 Subtotal ECS ESK EDI EDO O 4mA O 8mA O 4mA I CoS PRIORITY SETTING PIN# 199 PIN NAME ENPRITY I/O I DESCRIPTION Priority Queue Enable Internally pull down. Per port base pin setting priority function enable. If the pin is enabled, per port base priority settings used by EEPROM or CPU is invalid. Port base priority settings controlled by EEPROM or CPU will be valid when the pin is pull down. Per Port Priority Enable Active low. If pin pull high, the mapped port will act as high priority. 198-191 188-179 176-171 PRITY0 PRITY1 PRITY2 PRITY3 PRITY4 PRITY5 PRITY6 PRITY7 PRITY8 PRITY9 PRITY10 PRITY11 PRITY12 PRITY13 PRITY14 PRITY15 PRITY16 PRITY17 PRITY18 PRITY19 PRITY20 PRITY21 PRITY22 PRITY23 I P/N:PM0782 7 REV. 0.2, Apr, 18, 2001 MX98224EC Subtotal 25 CPU INTERFACE PIN# 203 PIN NAME ENCPU I/O I DESCRIPTION CPU Interface Enable Internally pull down. At reset, the pin is latched as CPU interface enable. CPU Selection The selected chip enable from CPU. CPU Input Clock The switch generates 8.3MHz serial clock to CPU. CPU Data Input/Output CPU read/write data & command. CPU Output Clock CPU generates 8.3MHz serial clock to Ethernet switch. 5 205 206 207 208 Subtotal CPUSEL OUTCLK IODATA INCLK I O 8mA I/O 4mA I LED INTERFACE PIN# 204 PIN NAME LEDA I/O O 8mA DESCRIPTION Address Table Self-test/Buffer Full LED Internally pull down. Initially, after power on or reset, address table will be tested and LEDC (Reset function) is keeping on until internal test finished. If any error found in address table, LEDA will keep on. After LEDC off, the switch is functional. If global buffer utilization is full within previous 40ms intervals, LEDA will be on 40ms. It will keep on if the buffer utilization keeps full within current intervals. Buffer Memory Test/Packet Loss LED Internally pull down. If power on or reset, LEDC (Reset function) is keeping on and all buffer memory will be tested. If buffer memory has an error found, LEDB will be on. After LEDB and LEDC off, switch self-test is done. If packet loss found, LEDB is keeping on 40ms within each 40ms time intervals. Reset/Broadcast Storm LED Internally pull up. If reset, LEDC is on until all internal memory test finished. Then, the pin will show the status of broadcast storm packets. If the number of broadcast packets stored in switch over threshold within 40ms time intervals, LEDC will be on 40ms. It will be shown until broadcast storm released. 3 203 LEDB O 8mA 202 LEDC O 8mA Subtotal P/N:PM0782 8 REV. 0.2, Apr, 18, 2001 MX98224EC MISCELLANEOUS PIN# 147 148 PIN NAME MDC MDIO I/O I/O 16mA I/O 16mA I DESCRIPTION Management Data Clock Internal pull down. The pin provides 2.5MHz clock for MDIO. Management Data Bi-directional RMII management port data pin. MDIO is synchronous with respect to MDC and is sampled on the rising edge of MDC. Chip Reset Active low; be held low for some time after power-on. 1.8V Core Power 150 33, 74, 96, 134, 169, 189, RESET# Vcc 16, 47, 62, Vdd 85, 120, 145, 177, 200 GND 17, 34, 48, 63, 75, 86, 97, 121, 135, 146, 170, 178, 190, 201 Subtotal 3.3V I/O Power Ground 31 P/N:PM0782 9 REV. 0.2, Apr, 18, 2001 MX98224EC EEPROM AND CPU CONTROL REGISTERS OFFSET 0x00H 0x01H 0x02H 0x03H 0x04H 0x05H 0x06H 0x07H 0x08H 0x09H 0x0AH 0x0BH 0x0CH 0x0DH 0x0EH 0x0FH 0x10H 0x11H 0x12H 0x13H 0x14H 0x15H 0x16H 0x17H 0x18H 0x19H 0x1AH REGISTER Port Base VLAN Group 0 (0-11) Port Base VLAN Group 0 (12-23) Port Base VLAN Group 1 (0-11) Port Base VLAN Group 1 (12-23) Port Base VLAN Group 2 (0-11) Port Base VLAN Group 2 (12-23) Port Base VLAN Group 3 (0-11) Port Base VLAN Group 3 (12-23) Port Base VLAN Group 4 (0-11) Port Base VLAN Group 4 (12-23) Port Base VLAN Group 5 (0-11) Port Base VLAN Group 5 (12-23) Port Base VLAN Group 6 (0-11) Port Base VLAN Group 6 (12-23) Port Base VLAN Group 7 (0-11) Port Base VLAN Group 7 (12-23) Port Base VLAN Group 8 (0-11) Port Base VLAN Group 8 (12-23) Port Base VLAN Group 9 (0-11) Port Base VLAN Group 9 (12-23) Port Base VLAN Group 10 (0-11) Port Base VLAN Group 10 (12-23) Port Base VLAN Group 11 (0-11) Port Base VLAN Group 11 (12-23) Configuration 0 & Port Base Priority (0-7) Port Base Priority (8-23) Configuration 1 0x32H 0x33H 0x34H OFFSET 0x1BH 0x1CH 0x1DH 0x1EH 0x1FH 0x20H 0x21H 0x22H 0x23H 0x24H 0x25H 0x26H 0x27H 0x28H 0x29H 0x2AH 0x2BH 0x2CH 0x2DH 0x2EH 0x2FH 0x30H 0x31H REGISTER Aging Timer Reserved 802.3x Pause Frame Timer MAC Address 0 MAC Address 1 MAC Address 2 IP/VLAN Tagging Base Priority (0-7) IP/VLAN Tagging Base Priority (8-15) IP/VLAN Tagging Base Priority (16-23) Reserved Reserved Reserved LED Control & VLAN Group Reset CPU Access Data PHY/Address Table Operation Command Flow Control Enable (8-23) Reserved Flow Control Enable (0-7) Reserved Reserved Reserved Auto-negotiation Disable (0-15) Auto-negotiation (16-23) & Force Speed Setting (0-7) Force Speed Setting (8-23) Force Half/Full Duplex Setting (0-15) Force Half/Full Duplex Setting (16-23) Note : 1. 93C46 EEPROM must be in 16-bit mode 2. The contents of EEPROM and CPU access registers are the same as following descriptions 3. (A-B) means port number setting from A to B P/N:PM0782 10 REV. 0.2, Apr, 18, 2001 MX98224EC Port Base VLAN Group 0 (0-11) (Reg00H), default = 0x0FFFH BIT 0.11-0 DESCRIPTION Port 0-11 VLAN Group 0 Default 1; all ports are into single group. One bit per port; e.g. bit 0 for port 0 and bit 11 for port 11 0 : disable; to be treat as an isolated port 1 : enable; to be a group 0 member N/A TYPE R/W DEFAULT 0xFFF 0.15-12 Port Base VLAN Group 0 (12-23) (Reg01H), default = 0x0FFFH BIT 1.11-0 DESCRIPTION Port 12-23 VLAN Group 0 Default 1; all ports are into single group. One bit per port; e.g. bit 0 for port 12 and bit 11 for port 23 0 : disable; to be treat as an isolated port 1 : enable; to be a group 0 member N/A TYPE R/W DEFAULT 0xFFF 1.15-12 Port Base VLAN Group 1 (0-11) (Reg02H), default = 0x0000H BIT 2.11-0 DESCRIPTION Port 0-11 VLAN Group 1 Default 0; group 1 not in use if all zero. One bit per port; e.g. bit 0 for port 0 and bit 11 for port 11 0 : disable; to be treat as an isolated port 1 : enable; to be a group 1 member N/A TYPE R/W DEFAULT 0x000 2.15-12 Port Base VLAN Group 1 (12-23) (Reg03H), default = 0x0000H BIT 3.11-0 DESCRIPTION Port 12-23 VLAN Group 1 Default 0; group 1 not in use if all zero. One bit per port; e.g. bit 0 for port 12 and bit 11 for port 23 0 : disable; to be treat as an isolated port 1 : enable; to be a group 1 member N/A TYPE R/W DEFAULT 0x000 3.15-12 P/N:PM0782 11 REV. 0.2, Apr, 18, 2001 MX98224EC Port Base VLAN Group 2 (0-11) (Reg04H), default = 0x0000H BIT 4.11-0 DESCRIPTION Port 0-11 VLAN Group 2 Default 0; group 2 not in use if all zero. One bit per port; e.g. bit 0 for port 0 and bit 11 for port 11 0 : disable; to be treat as an isolated port 1 : enable; to be a group 2 member N/A TYPE R/W DEFAULT 0x000 4.15-12 Port Base VLAN Group 2 (12-23) (Reg05H), default = 0x0000H BIT 5.11-0 DESCRIPTION Port 12-23 VLAN Group 2 Default 0; group 2 not in use if all zero. One bit per port; e.g. bit 0 for port 12 and bit 11 for port 23 0 : disable; to be treat as an isolated port 1 : enable; to be a group 2 member N/A TYPE R/W DEFAULT 0x000 5.15-12 Port Base VLAN Group 3 (0-11) (Reg06H), default = 0x0000H BIT 6.11-0 DESCRIPTION Port 0-11 VLAN Group 3 Default 0; group 3 not in use if all zero. One bit per port; e.g. bit 0 for port 0 and bit 11 for port 11 0 : disable; to be treat as an isolated port 1 : enable; to be a group 3 member N/A TYPE R/W DEFAULT 0x000 6.15-12 Port Base VLAN Group 3 (12-23) (Reg07H), default = 0x0000H BIT 7.11-0 DESCRIPTION Port 12-23 VLAN Group 3 Default 0; group 3 not in use if all zero. One bit per port; e.g. bit 0 for port 12 and bit 11 for port 23 0 : disable; to be treat as an isolated port 1 : enable; to be a group 3 member N/A TYPE R/W DEFAULT 0x000 7.15-12 P/N:PM0782 12 REV. 0.2, Apr, 18, 2001 MX98224EC Port Base VLAN Group 4 (0-11) (Reg08H), default = 0x0000H BIT 8.11-0 DESCRIPTION Port 0-11 VLAN Group 4 Default 0; group 4 not in use if all zero. One bit per port; e.g. bit 0 for port 0 and bit 11 for port 11 0 : disable; to be treat as an isolated port 1 : enable; to be a group 4 member N/A TYPE R/W DEFAULT 0x000 8.15-12 Port Base VLAN Group 4 (12-23) (Reg09H), default = 0x0000H BIT 9.11-0 DESCRIPTION Port 12-23 VLAN Group 4 Default 0; group 4 not in use if all zero. One bit per port; e.g. bit 0 for port 12 and bit 11 for port 23 0 : disable; to be treat as an isolated port 1 : enable; to be a group 4 member N/A TYPE R/W DEFAULT 0x000 9.15-12 Port Base VLAN Group 5 (0-11) (Reg0AH), default = 0x0000H BIT A.11-0 DESCRIPTION Port 0-11 VLAN Group 5 Default 0; group 5 not in use if all zero. One bit per port; e.g. bit 0 for port 0 and bit 11 for port 11 0 : disable; to be treat as an isolated port 1 : enable; to be a group 5 member N/A TYPE R/W DEFAULT 0x000 A.15-12 Port Base VLAN Group 5 (12-23) (Reg0BH), default = 0x0000H BIT B.11-0 DESCRIPTION Port 12-23 VLAN Group 5 Default 0; group 5 not in use if all zero. One bit per port; e.g. bit 0 for port 12 and bit 11 for port 23 0 : disable; to be treat as an isolated port 1 : enable; to be a group 5 member N/A TYPE R/W DEFAULT 0x000 B.15-12 P/N:PM0782 13 REV. 0.2, Apr, 18, 2001 MX98224EC Port Base VLAN Group 6 (0-11) (Reg0CH), default = 0x0000H BIT C.11-0 DESCRIPTION Port 0-11 VLAN Group 6 Default 0; group 6 not in use if all zero. One bit per port; e.g. bit 0 for port 0 and bit 11 for port 11 0 : disable; to be treat as an isolated port 1 : enable; to be a group 6 member N/A TYPE R/W DEFAULT 0x000 C.15-12 Port Base VLAN Group 6 (12-23) (Reg0DH), default = 0x0000H BIT D.11-0 DESCRIPTION Port 12-23 VLAN Group 6 Default 0; group 6 not in use if all zero. One bit per port; e.g. bit 0 for port 12 and bit 11 for port 23 0 : disable; to be treat as an isolated port 1 : enable; to be a group 6 member N/A TYPE R/W DEFAULT 0x000 D.15-12 Port Base VLAN Group 7 (0-11) (Reg0EH), default = 0x0000H BIT E.11-0 DESCRIPTION Port 0-11 VLAN Group 7 Default 0; group 7 not in use if all zero. One bit per port; e.g. bit 0 for port 0 and bit 11 for port 11 0 : disable; to be treat as an isolated port 1 : enable; to be a group 7 member N/A TYPE R/W DEFAULT 0x000 E.15-12 Port Base VLAN Group 7 (12-23) (Reg0FH), default = 0x0000H BIT F.11-0 DESCRIPTION Port 12-23 VLAN Group 7 Default 0; group 7 not in use if all zero. One bit per port; e.g. bit 0 for port 12 and bit 11 for port 23 0 : disable; to be treat as an isolated port 1 : enable; to be a group 7 member N/A TYPE R/W DEFAULT 0x000 F.15-12 P/N:PM0782 14 REV. 0.2, Apr, 18, 2001 MX98224EC Port Base VLAN Group 8 (0-11) (Reg10H), default = 0x0000H BIT 10.11-0 DESCRIPTION Port 0-11 VLAN Group 8 Default 0; group 8 not in use if all zero. One bit per port; e.g. bit 0 for port 0 and bit 11 for port 11 0 : disable; to be treat as an isolated port 1 : enable; to be a group 8 member N/A TYPE R/W DEFAULT 0x000 10.15-12 Port Base VLAN Group 8 (12-23) (Reg11H), default = 0x0000H BIT 11.11-0 DESCRIPTION Port 12-23 VLAN Group 8 Default 0; group 8 not in use if all zero. One bit per port; e.g. bit 0 for port 12 and bit 11 for port 23 0 : disable; to be treat as an isolated port 1 : enable; to be a group 8 member N/A TYPE R/W DEFAULT 0x000 11.15-12 Port Base VLAN Group 9 (0-11) (Reg12H), default = 0x0000H BIT 12.11-0 DESCRIPTION Port 0-11 VLAN Group 9 Default 0; group 9 not in use if all zero. One bit per port; e.g. bit 0 for port 0 and bit 11 for port 11 0 : disable; to be treat as an isolated port 1 : enable; to be a group 9 member N/A TYPE R/W DEFAULT 0x000 12.15-12 Port Base VLAN Group 9 (12-23) (Reg13H), default = 0x0000H BIT 13.11-0 DESCRIPTION Port 12-23 VLAN Group 9 Default 0; group 9 not in use if all zero. One bit per port; e.g. bit 0 for port 12 and bit 11 for port 23 0 : disable; to be treat as an isolated port 1 : enable; to be a group 9 member N/A TYPE R/W DEFAULT 0x000 13.15-12 P/N:PM0782 15 REV. 0.2, Apr, 18, 2001 MX98224EC Port Base VLAN Group 10 (0-11) (Reg14H), default = 0x0000H BIT 14.11-0 DESCRIPTION Port 0-11 VLAN Group 10 Default 0; group 10 not in use if all zero. One bit per port; e.g. bit 0 for port 0 and bit 11 for port 11 0 : disable; to be treat as an isolated port 1 : enable; to be a group 10 member N/A TYPE R/W DEFAULT 0x000 14.15-12 Port Base VLAN Group 10 (12-23) (Reg15H), default = 0x0000H BIT 15.11-0 DESCRIPTION Port 12-23 VLAN Group 10 Default 0; group 10 not in use if all zero. One bit per port; e.g. bit 0 for port 12 and bit 11 for port 23 0 : disable; to be treat as an isolated port 1 : enable; to be a group 10 member N/A TYPE R/W DEFAULT 0x000 15.15-12 Port Base VLAN Group 11 (0-11) (Reg16H), default = 0x0000H BIT 16.11-0 DESCRIPTION Port 0-11 VLAN Group 11 Default 0; group 11 not in use if all zero. One bit per port; e.g. bit 0 for port 0 and bit 11 for port 11 0 : disable; to be treat as an isolated port 1 : enable; to be a group 11 member N/A TYPE R/W DEFAULT 0x000 16.15-12 Port Base VLAN Group 11 (12-23) (Reg17H), default = 0x0000H BIT 17.11-0 DESCRIPTION Port 12-23 VLAN Group 11 Default 0; group 11 not in use if all zero. One bit per port; e.g. bit 0 for port 12 and bit 11 for port 23 0 : disable; to be treat as an isolated port 1 : enable; to be a group 11 member N/A TYPE R/W DEFAULT 0x000 17.15-12 P/N:PM0782 16 REV. 0.2, Apr, 18, 2001 MX98224EC Configuration 0 and Port Base Priority (0-7) (Reg18H), default = 0x0022H BIT 18.0 DESCRIPTION Continuous 16-time Collision Drop Disable 0 : packet that runs into 16 consecutive collision will be dropped 1 : packet that runs into 16 consecutive collision will NOT be dropped Timeout disable 0 : packet will NOT be dropped if packet has been queued over 1 second 1 : packet will be dropped in spite of packet being queue over 1 second CRC Hashing Selection 48-bit DA/SA address is translated separated into 12-bit entry pointer of address table for address learning and recognition. The translation is by aid of CRC generator within the switch controller. The index of entry pointer selection is defined by: 00 : bit [11:0] of CRC are selected 01 : bit [16:5] of CRC are selected 10 : bit [24:13] of CRC are selected 11 : bit [30:19] of CRC are selected Direct Mapping It means bit [63:52] of DA/SA address directly as an index of address table. 0 : CRC calculation to get the hashing index of address table 1 : direct mapping enable Reserved N/A Reserved Port 0-7 Priority Port base priority settings from port 0 to port 7. If external pins of port base priority are set, the content of EEPROM or CPU will be overridden. One bit per port; e.g. bit 8 for port 0 and bit 15 for port 7. 0 : disable 1 : enable, the port of packets always in high priority R/W R/W 1 0x00H TYPE R/W DEFAULT 0 18.1 R/W 1 18.3-2 R/W 00 18.4 R/W 1 18.5 18.6 18.7 18.15-8 R/W 0 Port Base Priority (8-23) (Reg19H), default = 0x0000H BIT 19.15-0 DESCRIPTION Port 8-23 Priority Port base priority settings from port 8 to port 23. If external pins of port base priority are set, the content of EEPROM or CPU will be overridden. One bit per port; e.g. bit 0 for port 8 and bit 15 for port 23. 0 : disable 1 : enable, the port of packets always in high priority TYPE R/W DEFAULT 0x0000H P/N:PM0782 17 REV. 0.2, Apr, 18, 2001 MX98224EC Configuration 1 (Reg1AH), default = 0x502EH BIT 1A.3-0 1A.5-4 Reserved Backoff Operation Mode In normal backoff algorithm, packet transmission delays a random time within 2n –1 slot time (1 slot time = 512 bit times) when collision occurs. The switch provides some modification of backoff algorithm to improve Ethernet performance on half- duplex connection. 00 : standard operation. 01 : first two collisions follow standard backoff. More than two collisions in transmission, packet resend delays 0-3 slot times. 10 : packet resend delays 0 slot time only when port buffer full. 11 : packet resend delays 0 slot time all the time. Back Pressure Disable Enable back pressure on half duplex connection for all ports 0 : enable 1 : disable N/A Reserved High/Low Priority Ratio Bit 9 to 11 means a decimal value for low priority packets to be transmitted whereas bit 12 to 14 to a decimal value for high priority packets. Followings are some example of high to low priority value. High Priority Value Bit 14 Bit 13 Bit 12 0/1 0 1A.15 0/1 1 0/1 1 Low Priority Value Bit 11 Bit 10 Bit 9 0 0 0 0 0 1 Meaning High priority port packets need to be sent first until empty; then, low priority packets The transmission ratio of high to low priority packets is 3 : 1 R/W 0 R/W R/W 0 0x28H DESCRIPTION TYPE R/W R/W DEFAULT 0xFH 00 1A.6 R/W 0 1A.7 1A.8 1A.14-9 Aging Out Enable the function of aging out from address table. 0 : enable 1 : disable Aging Timer (Reg1BH), default = 0x0005H BIT 1B.15-0 DESCRIPTION Aging timer provides for address table. The timer period is defined to age out the least unused entries on address table. The formula is age_timer (bit 0-15) X 65536 X 1ms. Here are some examples: Bit 15 – Bit 0 0x0001H 0x0005H 0x001BH 0x0037H P/N:PM0782 18 Aging Timer 65.5 sec 327.7 sec 1769.5 sec 3604.5 sec (around 1 min) (around 5.5 min) (around 30 min) (around 1 hr) REV. 0.2, Apr, 18, 2001 TYPE R/W DEFAULT 0x0005H MX98224EC Reserved (Reg1CH), default = 0xC350H BIT 1C.15-0 Reserved DESCRIPTION TYPE R/W DEFAULT 0xC350H 802.3x Pause Frame Timer (Reg1DH), default = 0x01FFH BIT 1D.4-0 1D.15-5 Reserved Flow Control Counter The timer determines the period, namely “pause time”, to inhibit packet transmission from attached host for flow control. The variable pause time of pause frame is equal to the decimal value times 32 plus 31 slot time. DESCRIPTION TYPE R/W R/W DEFAULT 0x1FH 0x1E0H MAC Address 0 (Reg1EH), default = 0x0000H BIT 1E.15-0 DESCRIPTION Switch’ s MAC ID for address bit [15:0] TYPE R/W DEFAULT 0x0000H MAC Address 1 (Reg1FH), default = 0x0000H BIT 1F.15-0 DESCRIPTION Switch’ s MAC ID for address bit [31:16] TYPE R/W DEFAULT 0x0000H MAC Address 2 (Reg20H), default = 0x0000H BIT 20.15-0 DESCRIPTION Switch’ s MAC ID for address bit [47:32] TYPE R/W DEFAULT 0x0000H IP/VLAN Tagging Base Priority (0-7) (Reg21H), default = 0x0000H BIT 21.7-0 DESCRIPTION TOS (IP Base) Enable for port 0-7 to recognize the TOS field of IP priority packets. One bit per port; e.g. bit 0 for port 0 and bit 7 for port 7. 0 : disable 1 : enable TCI (VLAN Tagging Base) Enable for port 0-7 to recognize the TCI field of VLAN priority packets. One bit per port; e.g. bit 8 for port 0 and bit 15 for port 7. 0 : disable 1 : enable TYPE R/W DEFAULT 0x00H 21.15-8 R/W 0x00H P/N:PM0782 19 REV. 0.2, Apr, 18, 2001 MX98224EC IP/VLAN Tagging Base Priority (8-15) (Reg22H), default = 0x0000H BIT 22.7-0 DESCRIPTION TOS (IP Base) Enable for port 8-15 to recognize the TOS field of IP priority packets. One bit per port; e.g. bit 0 for port 8 and bit 7 for port 15. 0 : disable 1 : enable TCI (VLAN Tagging Base) Enable for port 8-15 to recognize the TCI field of VLAN priority packets. One bit per port; e.g. bit 8 for port 8 and bit 15 for port 15. 0 : disable 1 : enable TYPE R/W DEFAULT 0x00H 22.15-8 R/W 0x00H IP/VLAN Tagging Base Priority (16-23) (Reg23H), default = 0x0000H BIT 23.7-0 DESCRIPTION TOS (IP Base) Enable for port 16-23 to recognize the TOS field of IP priority packets. One bit per port; e.g. bit 0 for port 16 and bit 7 for port 23. 0 : disable 1 : enable TCI (VLAN Tagging Base) Enable for port 8-15 to recognize the TCI field of VLAN priority packets. One bit per port; e.g. bit 8 for port 16 and bit 15 for port 23. 0 : disable 1 : enable TYPE R/W DEFAULT 0x00H 23.15-8 R/W 0x00H Reserved (Reg24H), default = 0xB081H BIT 24.15-0 Reserved DESCRIPTION TYPE R/W DEFAULT 0xB081H Reserved (Reg25H), default = 0x0040H BIT 25.15-0 Reserved DESCRIPTION TYPE R/W DEFAULT 0x0040H Reserved (Reg26H), default = 0x0082H BIT 26.15-0 Reserved DESCRIPTION TYPE R/W DEFAULT 0x0082H P/N:PM0782 20 REV. 0.2, Apr, 18, 2001 MX98224EC LED Control and VLAN Group Reset (Reg27H), default = 0x0200H BIT 27.0 DESCRIPTION Port Grouping Command When, initially, the execution of default values of the VLAN registers (Reg00H-17H) or VLAN grouping settings required via CPU/EEPROM, VLAN grouping contents need to write into the registers; then, grouping command is put into action. After grouping command is done, the bit will be self-clean to 0. 0 : Idle 1 : Port regrouping enable Reserved Broadcast Storm LED 0 : LED displays the broadcast storm symptom in high priority packets 1 : LED displays the broadcast storm symptom of all packets Packet Loss LED 0 : LED displays the high priority packet loss 1 : LED displays all packet loss N/A TYPE R/W DEFAULT 0 27.2-1 27.3 R/W R/W 00 1 27.4 R/W 1 27.15-5 0x010H CPU Access Data (Reg28H), default = 0x0000H BIT 28.15-0 DESCRIPTION Access Data Generally, bit 15-0 is the access data for PHY registers and address table. In case, CPU requires to select PHY ID and register number before PHY register access. The starting PHY ID for the switch is 0. Bit 4-0 can be presented for PHY register number and bit 9-5 for PHY ID in address selection of PHY registers operation. TYPE R/W DEFAULT 0x0000H PHY/Address Table Operation Command (Reg29H), default = 0x0000H BIT 29.0 DESCRIPTION CPU Action If CPU takes read/write actions to address table or PHY registers, set the bit on. After action done, the bit will be self-clean to 0. 0 : Idle 1 : CPU action CPU Read/Write Read or write action set to address table or PHY registers. 0 : Read operation 1 : Write operation PHY/ALR Selection CPU access to PHY or address table 0 : PHY access 1 : Address table access TYPE R/W DEFAULT 0 29.1 R/W 0 29.2 R/W 0 P/N:PM0782 21 REV. 0.2, Apr, 18, 2001 MX98224EC 29.5-3 PHY/ALR Command In PHY register access 000 : A searching function for PHY ID and PHY register number when CPU access data filled relevant information. 001 : A command for switch internal control register to CPU access data based on read operation or a command for CPU access data to register to switch internal control register based on write operation. 100 : A command for content of PHY register to switch internal control register based on read operation or a command for switch internal control register to PHY register based on write operation. In address table access 000 : MAC ID for address bit [15:0] access from CPU access data to switch internal control register based on CPU write operation. It also can be MAC ID access bit [15:0] from switch internal control register to CPU access data based on CPU read operation. 001 : MAC ID for address bit [31:16] access from CPU access data to internal control register and based on CPU write operation; and vice versa. 010 : MAC ID for address bit [47:32] access from CPU access data to switch internal control register based on CPU write operation; and vice versa. 011 : Status of address table entry access like port number bit [8:4], aging timer bit [3:1], and valid bit [0] from switch internal control register to CPU access data based on CPU read operation. 100 : Based on read operation from content of an address table entry to switch internal control register or write operation from switch internal control register to content of an address table entry. Frozen Port The switch provides frozen function for an entry in address table; that is, an entry with learned MAC address and port number as an input will protect not to be aging out when the port number and assigned MAC have been set. Frozen function can only work on the first layer of address table. It’ s because the entry of second-layer of address table should be for dynamic MAC address. If frozen port sets to all one and CPU read/write command is one, the frozen MAC address will be released. If frozen port sets all one and CPU read/write command is zero, the host processor will read the content of second layer of address table. Reserved R/W 0x0H 29.10-6 R/W 0x00H 29.15-11 R/W 0x00H Flow Control Enable (8-23) (Reg2AH), default = 0x0000H BIT 2A.15-0 DESCRIPTION Flow Control Enable IEEE 802.3x flow control for port 8-23. One bit per port; e.g. bit 0 for port 8 and bit 15 for port 23. 0 : disable 1 : enable TYPE R/W DEFAULT 0x0000H P/N:PM0782 22 REV. 0.2, Apr, 18, 2001 MX98224EC Reserved (Reg2BH), default = 0xFFFFH BIT 2B.15-0 Reserved DESCRIPTION TYPE R/W DEFAULT 0xFFFFH Flow Control Enable (0-7) (Reg2CH), default = 0x00FFH BIT 2C.7-0 2C15-8 Reserved Flow Control Enable IEEE 802.3x flow control for port 0-7. One bit per port; e.g. bit 8 for port 0 and bit 15 for port 7. 0 : disable 1 : enable DESCRIPTION TYPE R/W R/W DEFAULT 0xFFH 0x00H Reserved (Reg2DH), default = 0x0000H BIT 2D.15-0 Reserved DESCRIPTION TYPE R/W DEFAULT 0x0000H Reserved (Reg2EH), default = N/A BIT 2E.15-0 Reserved DESCRIPTION TYPE RO DEFAULT N/A Reserved (Reg2FH), default = N/A BIT 2F.15-0 Reserved DESCRIPTION TYPE RO DEFAULT N/A Auto-negotiation (0-15) (Reg30H), default = 0x0000H BIT 30.15-0 DESCRIPTION Auto-negotiation Disable Auto-negotiation operation of MDIO. When port base auto-negotiation disable, the switch port will not listen the final response from PHY. One bit per port; e.g. bit 0 for port 0 and bit 15 for port 15. 0 : enable auto-negotiation 1 : disable auto-negotiation TYPE R/W DEFAULT 0x0000H P/N:PM0782 23 REV. 0.2, Apr, 18, 2001 MX98224EC Auto-negotiation (16-23) & Force Speed Setting (0-7) (Reg31H), default = 0xFF00H BIT 31.7-0 DESCRIPTION Auto-negotiation Disable Auto-negotiation operation of MDIO. When port base auto-negotiation disable, the switch port will not listen the final response from PHY. One bit per port; e.g. bit 0 for port 16 and bit 7 for port 23. 0 : enable auto-negotiation 1 : disable auto-negotiation Force Speed Operation When auto-negotiation off, the port will be set at fixed speed. In EEPROM, force settings will be automatically written into PHY registers at initialization. Force settings by CPU requires extra CPU write operation into PHY; so port-base speed operations can keep consistency. One bit per port; e.g. bit 8 for port 0 and bit 15 for port 7. 0 : force 10Mbps 1 : force 100Mbps TYPE R/W DEFAULT 0x00H 31.15-8 R/W 0xFFH Force Speed Setting (8-23) (Reg32H), default = 0xFFFFH BIT 32.15-0 DESCRIPTION Force Speed Operation One bit per port; e.g. bit 0 for port 8 and bit 15 for port 23. 0 : force 10Mbps 1 : force 100Mbps TYPE R/W DEFAULT 0xFFFFH Force Half Duplex Setting (0-15) (Reg33H), default = 0xFFFFH BIT 33.15-0 DESCRIPTION Force Half Duplex Operation When auto-negotiation off, the port will be set at fixed duplex. In EEPROM, force settings will be automatically written into PHY registers at initialization. Force settings by CPU requires extra CPU write operation into PHY; so port-base duplex operations can keep consistency. One bit per port; e.g. bit 0 for port 0 and bit 15 for port 15. 0 : force half duplex 1 : force full duplex TYPE R/W DEFAULT 0xFFFFH Force Half Duplex Setting (16-23) (Reg34H), default = 0x00FFH BIT 34.7-0 DESCRIPTION Force Half Duplex Operation One bit per port; e.g. bit 0 for port 16 and bit 7 for port 23. 0 : force half duplex 1 : force full duplex N/A TYPE R/W DEFAULT 0xFF 34.15-8 P/N:PM0782 24 REV. 0.2, Apr, 18, 2001 MX98224EC FUNCTIONAL DESCRIPTION Clocks MX98224EC requires a unique 50MHz clock signal for both RMII and system requirement at CLK input pin. Also, the switch generates an 8.3MHz output clock to CPU and the processor feedback the same clock rate back to the switch. The 2.5MHz clock applies on MDC/MDIO interface and 390KHz refers EEPROM interface. Reset When power on, a hard reset is initiated by an active low pulse on RESET# pin. The initialization process loads all ports configurable parameters, resets internal state machines to idle, initializes embedded memory and address table. At the completion of the reset sequence, all ports are presented for packet transmission and reception. RMII Interface Reduced Media Independent Interface (RMII) comprises a low pin count intended for use between Ethernet PHYs and switch ASICs. The management interface (MDC/MDIO) is assumed to be identical to that defined in IEEE 802.3u. The RMII specification has been optimized for using in high port density interconnect devices which require independent treatment of the data paths. The primary motivator is a switch ASIC which requires independent data streams between the MAC and PHY. CLK CLK is a continuous clock that provides the timing reference for CRSDV_0-23, RXD_0-23[1:0], TXEN_0-23, and TXD_0-23[1:0]. The switch choose to provide CLK as an input for system and RMII use and each PHY device shall have an input corresponding to this clock but may use a single clock input for multiple PHYs implemented on a single IC. Carrier Sense/Receive Data Valid CRSDV_0-23 shall be asserted by the PHY when the receive medium is non-idle. The specifics of the definition of idle for 10BASE-T and 100BASE-X are contained in IEEE 802.3 and IEEE 802.3u. CRSDV0-23 is asserted asynchronously on detection of carrier due to the criteria relevant to the operating mode. That is, in 10BASE-T mode, when squelch is passed or, in 100BASE-X mode, when 2 non-contiguous zeroes in 10 bits are detected carrier is said to be detected. If the PHY has additional bits to be presented on RXD_0-23[1:0] following the initial deassertion of CRSDV_0-23, then the PHY shall assert CRSDV_0-23 on cycles of CLK which present the second di-bit of each nibble and deassert CRSDV_0-23 on cycles of CLK which present the first di-bit of a nibble. Receive Data RXD_0-23[1:0] shall transition synchronously to CLK. For each clock period in which CRSDV_0-23 is asserted, RXD_0-23[1:0] transfers two bits of recovered data from the PHY. In some cases, for example before data recovery or during error conditions, a pre-determined value for RXD_0-23[1:0] is transferred instead of recovered data. RXD_0-23[1:0] shall be “00” to indicate idle when CRSDV_0-23 is deasserted. Values other than “00” on RXD_023[1:0] while recovered from CRSDV_0-23 is de-asserted shall be ignored by the MAC. Upon assertion of CRSDV_0-23, the PHY shall ensure that RXD_0-23[1:0] is equal to ”00” until proper receive decoding takes place. Transmit Enable TXEN_0-23 indicates that the MAC is presenting di-bits on TXD_0-23[1:0] for transmission. TXEN_0-23 shall be asserted synchronously with the first nibble of the preamble and shall remain asserted while all di-bits to be transmitted are presented. TXEN_0-23 shall be negated prior to the first CLK rising edge following the final di-bit of a frame. TXEN_0-23 shall transition synchronously with respect to CLK. Transmit Data TXD_0-23[1:0] shall transition synchronously with respect to CLK. When TXEN_0-23 is asserted, TXD[1:0] are accepted for transmission by the PHY. TXD_0-23[1:0] shall be “00” to indicate idle when TXEN_0-23 is deasserted. Values other than “00” on TXD_0-23[1:0] while TXEN_0-23 is deasserted shall be ignored by the PHY. P/N:PM0782 25 REV. 0.2, Apr, 18, 2001 MX98224EC PHY Management The PHY determines the operation mode of each port, which are classified as 10Mbps-half duplex, 10Mbps-full duplex, 100Mbps-half duplex, 100Mbps-full duplex. The MAC of each port is connected to the PHY through RMII interface. The PHY starting ID mapped to the switch is zero. The switch supports PHY management through the serial MDC/MDIO interface. The switch will continuously read the registers of each PHY based on PHY ID to get the latest information such as link status, speed, operation mode of each port while it is in auto-negotiation. When a port of the switch forced at fixed operation mode, it will not listen any response from the PHY through MDC/MDIO so that consistent speed and duplex in PHY as well as switch is required in force operation mode. Frame Reception The frame received on 2-bit wide receive channel of RMII interface is queued in receive FIFO, and then stored into embedded buffer memory. Several error conditions will be identified during data reception. 1.Runt frame error, if the frame size is less than 64 bytes; 2.CRC error, if FCS is not matched to the result of CRC calculation; 3.Long frame error, if frame size is larger than 1536 bytes; 4.Alignment error, if frame length is of non-integral number of octets; The above frames will be discarded. If no errors have been detected, the frame is stored and forwarded to egress port at wire speed. Several pages of buffer memory could be occupied for frame storage, on each page free memory is allocated. The data link management frames, namely IEEE 802.3x "pause" frame is recognized and no frame storage occurs. Frame Transmission Frame transmission begins while the output queue of physical port is not empty. The frame data is moved to output FIFO from embedded buffer memory, and converted to 2-bit stream through transmit channel of RMII interface. MX98224EC transmits frames in accordance to IEEE 802.3 standard. The egress port is responsible for preamble insertion, collision back-off, and inter packet gap keeping. While late collision happens on half-duplex port, the transmitted frame is aborted. If a packet has continuously met 16-time collisions, it will be dropped and the packet will be recovered by upper protocol. In full-duplex mode, the egress port ignores the signaling of carrier activity and collision detection on channel media. Broadcast Storm Control Three types of frames are viewed as broadcast frames in MX98224EC: 1. Received frame with DL_DA as FF-FF-FF-FF-FF-FF 2. Received frame with DL_DA as 1?-??-??-??-??-?? 3. Received frame with unknown destination (unicast or multicast) address To prevent network melted down, a state of complete network overload, due to broadcast storm (incorrect packet broadcast on a network that cause almost all hosts respond at once and hence storming the network with broadcast packets), users can program to restrict the storage amount of broadcast frames in MX98224EC. While the storage of broadcast frame goes over the threshold, the next coming broadcast frame(s) is dropped. Flow Control Flow control is implemented to avoid abnormal packet drop due to traffic congestion on egress ports. Basically, alternative back-pressure mechanism uses jam packet in half-duplex and 802.3x pause frame does in full-duplex mode. Flow control is active or inactive based on the internal per port and global reception thresholds in buffer. The switch implements standard 802.3x flow control whose frame is defined as follow. P/N:PM0782 26 REV. 0.2, Apr, 18, 2001 MX98224EC 6 Octets DA 6 Octets SA 2 Octets Type 2 Octets 2 Octets 42 Octets PAD Opcode Pause_Time 802.3x PAUSE Frame Format The diagram shown above is IEEE 802.3x pause frame format whereas DA presented for destination MAC adress, SA for source MAC address, pause frame type defined as 0x8808, opcode for pause operation (0x0001), default pause time for the switch to be 0x1FFF, and pad for all zero. The value of pause timer is changable by EEPROM or CPU. DA field of pause frame should be 0x0180C2000001 before transmission. Address Learning and Recognition After a good packet is received, address resolution logic begins address lookup. The destination MAC address and source MAC address associated are retrieved. The source MAC address is used to build up an address table. By searching the address table, if a unicast destination MAC address is recognized, the stored frame is forwarded to destined port. Initially, a unicast destination MAC address of a packet does not know the outgoing port number so that the stored frame is forwarded as a broadcast packet. In both of address learning and recognition, 48-bit MAC address is converted into a 12-bit search index via hash transformation. The switch offers two different hashing schemes; one is called direct mapping and the other is CRC mapping. In learning, an entry designated by the search index is checked to be valid or not. If non-valid, a new entry is generated with putting the information of source MAC address and ingress port number. A 2-layer structure is provided in learning mechanism. If valid, the 2-layer mechanism can keep 2 different MAC addresses in one certain entry to increase hashing resolution. If congestion found for an entry of the 2-layer structure, switch will compare the two numbers of the aging timer and replace the MAC record with older aging time to the new MAC. In recognition, the MAC address in table entry designated by search index is used to compare with destination MAC address. If both are matched, the associated port number in address table entry is the destination port. Otherwise, the received frame will be classified as a broadcast frame, and be flooded through every port (except source port). The memory space within MX98224EC can keep up to 8K MAC addresses. Aging mechanism is supported, namely the address information is aged out if not be referred in 300sec (default, the parameter is programmable). And, the entry of the record can be for newly learnt MACs kept in table. 2-priority Queue Class of Service (CoS) Class of Service denotes the classification of traffic used to differentiate services among traffic classes. MX98224EC offers 2-level priority (High and Low) queues, which catch the priority information in the TOS field, port base, or VLAN tag in the incoming frames as standard IEEE 802.1Q defines. In this way, the switch controller guarantees the service for high priority frames to some extent, depending on the load condition of incoming traffic. (At least, the high priority service offers better than that of best effort service.) It also provides different service ratio settings for users to shape the prioritized frames on the streams in the incoming traffic. Port-based VLAN A Virtual LAN (VLAN) is a broadcast domain or a network segment which enables multiple stations on different physical locations to communicate with each other as if they were on the same LAN. With all the advantages such as increasing performance, bandwidth utilization efficiency and security as well as preventing broadcast storm, PortBased VLAN is the most practical and economical form of VLAN. MX98224EC supports up to 12 port-based VLAN groups which applies the overlapped VLAN scheme. That is, the 24 switch ports can be divided into 12 VLAN port-groups. By configuring the port with its VLAN membership, each port is assigned to one or more (up to 12) groups. Ports belonging to different groups are independent, which means P/N:PM0782 27 REV. 0.2, Apr, 18, 2001 MX98224EC their network activity or fundamental network broadcasting will not affect or get distributed across those VLAN groups to each other. In this way, it can reduce the need for unwanted traffic in the network. Moreover, the damaged/abnormal ports can be isolated by removing them from VLAN groups' list, so as to prevent network meltdown. Port-based VLAN in MX98224EC is also very flexible that every port can be shared by multiple groups as the "trunk port" while the other unshared ports are remained independent. Queue Management MX98224EC utilizes the store-and-forward switching scheme, which needs memory for frame reception and transmission buffering. In MX98224EC, the embedded buffer memory is partitioned into pages which dynamically allocates the related frame data and switching information. The buffer management control unit dispatches pointers pointing to those pages upon frames reception of the egress ports. For unicast frames, the occupied buffer pages are released after the corresponding ports complete transmission. Their pointers are returned to buffer management control unit for reuse. For broadcast frames, the switch controller count the times of transmission of the same broadcast frame till all ports finish the broadcast transmission, then the occupied memory space are released to the free buffer pool. Since there are various kinds of page/pointer requests for the buffer management, a queue manager is used in MX98224EC to handle those access requests. Via a proprietary arbitration method, the queue manager grants fair enough throughput for each port to transmit at wire speed. 93C46 EEPROM Interface Provide serial interface to load the values of external EEPROM which switch can configure in advance. At initial stage, switch will loads the data to internal registers and operates as expected. Either EEPROM or CPU interface can be used once a time. CPU Interface MX98224EC provides another powerful way to configure the value of register via CPU, which can access its as well as PHY registers and the address table at any time. Basically, MAC address look up, content of address table status and frozen a dedicated address are the major function for CPU access through address table. Following is the basic system diagram for the connection of host processor, switch, and PHY. Octal PHY OUTCLK Host Processor INCLK IODATA MX98224EC Switch MDC Octal PHY Octal PHY MDIO Serial Management Block Diagram via Switch and PHY P/N:PM0782 28 REV. 0.2, Apr, 18, 2001 MX98224EC The switch generates an OUTCLK clock to host processor and the same frequency will be back to the switch via INCLK pin. There is a data format defined under below table which specifies a communication between the host processor and switch at serial IODATA pin. IODATA and MDIO are bi-direction I/O. The serial management format starts with start bit, then, follows operator, 10-bit register address, turn around, 16-bit content of data, and an idle bit. A command/response from host processor to the switch registers, Reg28H and Reg29H, can be given based on read/write operation, register address selection, and data. Command Read Write Start Bit 01 01 Operator 10 01 Register Address AAAAAAAAAA AAAAAAAAAA Turn Around Z0 10 Data DDDDDDDDDDDDDDDD DDDDDDDDDDDDDDDD Idle Z Z LED Interface MX98224EC has three LEDs. At initial stage, these represent address table self-test, memory test, and reset status respectively. And at normal state, these represent buffer full, packet loss, and broadcast storm status. Users can monitor the status of switch network via the LEDs. P/N:PM0782 29 REV. 0.2, Apr, 18, 2001 MX98224EC TIMING DIAGRAM Reset and Clock Timing t03 t01 CLK RESET# t02 T# .t01 .t02 .t03 System clock period DESCRIPTION MIN 20 9 1 TYP 20.2 10 MAX UNIT ns System clock high time RESET# low pulse duration 11 ns ms P/N:PM0782 30 REV. 0.2, Apr, 18, 2001 MX98224EC PHY Management (MDIO) Reading Timing MDC t11 t12 t13 t14 TA t15 t16 MDIO Register Address Q15 Q0 T# .t11 .t12 .t13 .t14 .t15 .t16 MDC high time MDC clock period DESCRIPTION MIN TYP 200 400 MAX UNIT ns ns MDC falling edge to MDIO delay MDC falling edge to MDIO Hi-Z MDIO setup time MDIO hold time 3 3 2 2 8 8 ns ns ns ns P/N:PM0782 31 REV. 0.2, Apr, 18, 2001 MX98224EC RMII Interface Timing CLK t21 t22 TXEN t23 t24 TXD t25 t26 CSRSDV t27 t28 RXD T# .t21 .t22 .t23 .t24 .t25 .t26 .t27 .t28 CLK high time CLK clock period CLK to TXEN delay CLK to TXD delay CRSDV setup time CRSDV hold time RXD setup time RXD hold time DESCRIPTION MIN 9 TYP 10 20 MAX 11 UNIT ns ns 3.5 3.5 0 4 0 4 10.5 11.5 ns ns ns ns ns ns P/N:PM0782 32 REV. 0.2, Apr, 18, 2001 MX98224EC EEPROM Interface Timing t31 ESK t37 t32 ECS t35 t36 t33 SB OP OP A5 A0 t39 t310 t34 EDO 0 D15 D0 t38 EDI T# .t31 .t32 .t33 .t34 .t35 .t36 .t37 .t38 .t39 .t310 ESK clock 93C46 chip enable DESCRIPTION MIN TYP 2560 27 10 17 3 MAX UNIT ns ESK ESK ESK ns ns 93C46 command input cycle 93C46 data output cycle 93C46 data input setup time 93C46 data input hold time 93C46 chip select setup time 93C46 chip select hold time 93C46 data output setup time 93C46 data output hold time 3 ns ns 3 ns ns P/N:PM0782 33 REV. 0.2, Apr, 18, 2001 MX98224EC CPU Interface Timing t41 CLK t44 t42 Data IO t46 CPUSEL t43 t45 T# .t41 .t42 .t43 .t44 .t45 .t46 CPU clock period Data IO setup timing DESCRIPTION MIN TYP 120 10 10 10 10 3840 MAX UNIT ns ns ns ns ns ns Chip select setup timing Data IO hold timing Chip select hold timing Chip select period P/N:PM0782 34 REV. 0.2, Apr, 18, 2001 MX98224EC ELECTRONICAL SPECIFICATION Absolute Maximum Rating Parameter I/O Supply Voltage Core Supply Voltage Input Voltage Output Voltage Storage Temperature Operation Temperature latch-up Current SYMBOL Vdd VCC VI VO TSTG TOPR TLAT MIN -0.5 -0.5 -0.5 -0.5 -65 -40 MAX 4.6 2.5 6 6 150 125 UNIT V V V V C C mA Recommended Operating Conditions Parameter I/O Supply Voltage Core Supply Voltage Operating Temperature Power Dissipation Junction Temperature Low-level Input Voltage High-level Input Voltage Tj VIL VIH 0 -0.3 2.0 125 0.8 5.5 C V V SYMBOL Vdd VCC TOPR MIN 3.0 1.62 0 MAX 3.6 1.98 70 UNIT V V C DC Characteristics Parameter Output High Voltage Output Low Voltage High Impedance State Output Current Output High Current (@VOH = 2.4V ) Output Low Current (@VOL = 0.4V) Input High Voltage Input Low Voltage Supply Current SYMBOL VOH VOL IOZ IOH IOL VIH VIL ICC mA MIN 2.4 MAX UNIT V 0.4 ±1 6.2 4.5 76.0 30.3 V µA mA mA P/N:PM0782 35 REV. 0.2, Apr, 18, 2001 MX98224EC PACKAGE INFORMATION P/N:PM0782 36 REV. 0.2, Apr, 18, 2001 MX98224EC REVISION HISTORY Revision 0.2 Description Speed/duplex settings change to FORCE from REG31H to REG34H Page 24 Date 04/18/2001 P/N:PM0782 37 REV. 0.2, Apr, 18, 2001 MX98224EC TOP SIDE MARKING MX98224EC MX98224EC is MXIC part No. “E” : PQFP “C” : Commercial grade line 2 : Assembly Date Code. line 3 : Wafer Lot No. line 4 : “36C” : Revision code “A” : Bonding option “X” : Not used line 5 : State line 1 : C0013 F40044937B1 36CAX TAIWAN MACRONIX INTERNATIONAL CO.,LTD. HEADQUARTERS: TEL:+886-3-578-6688 FAX:+886-3-563-2888 EUROP OFFICE: TEL:+32-2-456-8020 FAX:+32-2-456-8021 JAPAN OFFICE: TEL:+81-44-246-9100 FAX:+81-44-246-9105 SINGAPORE OFFICE: TEL:+65-348-8385 FAX:+65-348-8096 TAIPEI OFFICE: TEL:+886-2-2509-3300 FAX:+886-2-2509-2200 MACRONIX AMERICA, INC. TEL:+1-408-453-8088 FAX:+1-408-453-8488 CHICAGO OFFICE TEL:+1-847-963-1900 FAX:+1-847-963-1909 http://www.macronix.com P/N:PM0782 38 REV. 0.2, Apr, 18, 2001