OMR7812ST

OMR7805SR OMR7812SR OMR7815SR OMR7805ST OMR7812ST OMR7815ST OMR7805NM OMR7812NM OMR7815NM OMR7805NH OMR7812NH OMR7815NH 300 kRAD RADIATION TOLERANT 1.5 AMP POSITIVE FIXED VOLTAGE REGULATORS 300K Rad Tolerant Three Terminal, Positive Fixed Voltage Regulators In Hermetic Packages Please see mechanical outlines herein FEATURES • • • • • • • Isolated & Non-Isolated Hermetic Packages Output Voltages: +5V, +12V, +15V (Other Voltages Available) Output Voltages Set Internally To ±1% or ±2% Built-In Thermal Overload Protection Short Circuit Current Limiting Radiation Tolerant up to 450 K Rad (Si) Available Hi-Rel Screened, Class B and Class S, MIL-STD-883 DESCRIPTION These three terminal negative regulators are supplied in a high density hermetically sealed metal package and are available hi-rel screened. All protective features are designed into the circuit, including thermal shutdown, current limiting and safe-area control. With heat sinking, they can deliver over 1.5 amps of output current. These units feature internally trimmed output voltages to ±1% or 2% of nominal voltage. Standard voltages are +5V, +12V, and +15V. However, other voltages are available up to +24 volts. These devices are ideally suited for Space applications where small size, high reliability, and radiation tolerance is required. The high level of Radiation Tolerance of these devices makes them a desirable choice for LEO and many MEO and GEO communication satellites. Radiation testing is performed on a single wafer by wafer basis. Random die samples per wafer are selected, packaged and radiation tested to qualify each individual semiconductor wafer-by-wafer. ABSOLUTE MAXIMUM RATINGS @ 25°C Input Voltage . . . . . . .. . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -35 V Operating Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to + 150°C Storage Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to + 150°C Power Dissipation: TO-205. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 W TO-257/SMD-1/ D2 Pac . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 W Lead Temperature (Soldering 10 seconds). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300°C Surface Mount Package Soldering Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250°C Thermal Resistance, Junction to Case: TO-205. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17°C/W TO-257(Isolated), D2 Pac (Isolated) . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . 4.2°C/W SMD-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . 3.5°C/W Maximum Output Current: TO-205 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.5 A TCase-All Others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3A Radiation Tolerant - Total Dose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300 K Rad (Si) 0 04 R1 Supersedes 9 12 R0 OMR7805SR OMR7812SR OMR7815SR Parameter OMR7805ST OMR7812ST OMR7815ST Symbol VOUT VRLINE OMR7805NM OMR7812NM OMR7815NM Test Conditions TA = 25°C VIN = 7.5V to 20V OMR7805NH OMR7812NH OMR7815NH Min. 4.92 Max. 5.08 5.15 5 Unit V V mV mV mV mV mV mV mV mV mA mA mA ELECTRICAL CHARACTERISTICS 5 Volt Output Voltage VIN = 10V, Io = 500mA, -55°C ≤ TA ≤ 125°C (unless otherwise specified) • • 4.85 Line Regulation (Note 1) VIN = 7.5V to 20V VIN = 8.0V to 12V 12 4 • Load Regulation (Note 1) IO = 250mA to 750 mA VRLOAD IO = 5mA to 1.5 Amp 10 12 • • 25 6 15 6 Standby Current Drain ISCD ∆ISCD (Line) ∆ISCD (Load) VDO IO (pk) IDS ∆VIN ∆VOUT NO ∆VOUT ∆t TA = 25°C, ∆VOUT = 100mV, IO = 1.0A TA = 25°C VIN = 35V 1.5 IO = 5mA to 1000mA VIN = 7.5V to 20V Standby Current Drain Change With Line Standby Current Drain Change With Load Dropout Voltage Peak Output Current Short Circuit Current (Note 2) Ripple Rejection • • • 6.5 0.8 0.5 mA 2.5 3.3 1.2 V A A A dB dB • f =120 Hz, ∆VIN = 10V (Note 3) TA = 25°C, f =10 Hz to 100KHz TA = 25°C, t = 1000 hrs. 66 2.8 • 60 40 Output Noise Voltage (Note 3) Long Term Stability (Note 3) µV/V RMS 75 mV ELECTRICAL CHARACTERISTICS 12 Volt Parameter Output Voltage Symbol VOUT VRLINE VIN = 19V, Io = 500mA, -55°C ≤ TA ≤ 125°C (unless otherwise specified) Min. 11.88 Max. 12.12 12.36 18 Unit V V mV mV mV mV mV mV mV mV mA mA mA Test Conditions TA = 25°C VIN = 14.5V to 27V • • 11.64 Line Regulation (Note 1) VIN = 14.5V to 27V VIN = 16V to 22V 50 9 • Load Regulation (Note 1) IO = 250mA to 750 mA VRLOAD IO = 5mA to 1.5 Amp 30 32 • • 60 20 40 6.0 Standby Current Drain ISCD ∆ISCD (Line) ∆ISCD (Load) VDO IO (pk) IDS ∆VIN ∆VOUT NO ∆VOUT ∆t ∆VOUT = 100mV, IO = 1.0A TA = 25°C VIN = 35V IO = 5mA to 1000mA VIN = 15V to 30V Standby Current Drain Change With Line Standby Current Drain Change With Load Dropout Voltage Peak Output Current Short Circuit Current (Note 2) Ripple Rejection • • • • 1.5 6.5 0.8 0.5 mA 2.5 3.3 1.2 V A A A dB dB • f =120 Hz, ∆VIN = 10V (Note 3) TA = 25°C, f =10 Hz to 100KHz TA = 25°C, t = 1000 hrs. 61 2.8 • 54 40 Output Noise Voltage (Note 3) Long Term Stability (Note 3) µV/V RMS 120 mV Notes: 1. Load and Line Regulation are specified at a constant junction temperature. Pulse testing with low duty cycle is used. Changes in output voltage due to heating effects must be taken into account separately. 2. Short Circuit protection is only assured up to VIN = 35V. 3. If not tested, shall be guaranteed to the specified limits. 4. The • denotes the specifications which apply over the full operating temperature range. 5. Refer to curves for typical characteristics versus Total Dose Radiation Levels. OMR7805SR OMR7812SR OMR7815SR ELECTRICAL CHARACTERISTICS 15 Volt Parameter Output Voltage Symbol VOUT VRLINE OMR7805ST OMR7812ST OMR7815ST OMR7805NM OMR7812NM OMR7815NM Min. 14.8 Max. 15.2 15.4 20 OMR7805NH OMR7812NH OMR7815NH Unit V V mV mV mV mV mV mV mV mV mA mA mA VIN = 23V, Io = 500mA, -55°C ≤ TA ≤ 125°C (unless otherwise specified) Test Conditions TA = 25°C VIN = 18.5V to 30V • • 14.6 Line Regulation (Note 1) VIN = 17.5V to 30V VIN = 20V to 26V 50 15 • Load Regulation (Note 1) VRLOAD IO = 5mA to 1.5 Amp IO = 5mA to 1.0 Amp IO = 250mA to 750 mA 25 35 • • 75 21 45 6.0 Standby Current Drain ISCD ∆ISCD (Line) ∆ISCD (Load) VDO IO (pk) IDS ∆VIN ∆VOUT NO ∆VOUT ∆t TA = 25°C, ∆VOUT = 100mV, IO = 1.0A TA = 25°C VIN = 35V 1.5 IO = 5mA to 1000mA VIN = 18.5V to 30V Standby Current Drain Change With Line Standby Current Drain Change With Load Dropout Voltage Peak Output Current Short Circuit Current (Note 2) Ripple Rejection • • • 6.5 0.8 0.5 mA 2.5 3.3 1.2 V A A A dB dB • f =120 Hz, ∆VIN = 10V (Note 3) TA = 25°C, f =10 Hz to 100KHz TA = 25°C, t = 1000 hrs. 54 2.8 • 52 40 Output Noise Voltage (Note 3) Long Term Stability (Note 3) µV/V RMS 150 mV Notes: 1. Load and Line Regulation are specified at a constant junction temperature. Pulse testing with low duty cycle is used. Changes in output voltage due to heating effects must be taken into account separately. 2. Short Circuit protection is only assured up to VIN = 35V. 3. If not tested, shall be guaranteed to the specified limits. 4. The • denotes the specifications which apply over the full operating temperature range. 5. Refer to curves for typical characteristics versus Total Dose Radiation Levels. RADIATION TEST PROGRAM The following chart is a summary of the test data collected on Radiation Tolerant OMR7805/12/15 at various doses. The chart depicts the Total Radiation Dose that each device was exposed to on a step stress irradiation basis prior to failure. Failure is defined as any electrical test that does not meet the limits of the device per the published data sheet specifications after radiation testing. Omnirel P/N OMR7805/12/15 5K 10K 20K 30K 50K 60K 70K 80K 100K 150K 200 250 300 350 400 450 KRAD Test Points X X X X X X OMR7805SR OMR7812SR OMR7815SR OMR7805ST OMR7812ST OMR7815ST OMR7805NM OMR7812NM OMR7815NM OMR7805NH OMR7812NH OMR7815NH OMNIREL’S RADIATION TEST PROCEDURE • • • • • Radiation Testing is performed on a single wafer by wafer basis. Each wafer is identified and a random sample of 5 die per wafer is selected. The die are then individually assembled in a hermetic package, data logged, electrically tested, hi-rel screened and then submitted to radiation testing. The packaged die are submitted to Steady State Total Dose radiation per Method 1019, Condition A, at a dose rate of 50 RAD/sec biased at maximum supply voltage. Final electrical test is performed within two hours of both Total Dose Radiation level from a Cobalt 60 source and 168 hr, 100°C annealing process. Read and record data including two non-radiated control samples. • • The wafer is then qualified only if samples from wafers meet full electrical specifications after 150% of total dose rating as specified in each product data sheet. Omnirel’s controlling specifications are as follows: For Voltage Regulators the controlling specification is MIL-PRF- 38534/MIL-STD-883. For Rectifiers/Schottky the controlling specification is MIL-PRF-19500/MIL-STD-750. AVAILABLE PRODUCT SCREENING Standard Class Level Screening Per MIL-PRF-38535 Screen *Level B Test Method Wafer Lot Acceptance Non-destructive Bond Pull Pre-Cap Visual Inspection Temperature Cycle Constant Acceleration Visual Inspection PIND Test Serialization Pre-Burn-In Electrical Burn-In Interim Electrical PDA Calculations Final Electrical Fine & Gross Seal Radiographic Conformance Inspection** Final Visual Inspection --------2010 1010 2001 ------------Data Sheet 1015/160 hrs. ----5% Functional Data Sheet 1014 ----GR A 2009 *Level S Test Method 5007 ----2010 1010 2001 ----2020 ----Data Sheet 1015/240hrs. Data Sheet 5% Functional Data Sheet 1014 2012/Two Views GR A 2009 Required --------100% 100% 100% 100% --------100% 100% ----Lot 100% 100% ----100% Sample Required 100% ----100% 100% 100% 100% 100% 100% 100% 100% 100% Lot 100% 100% 100% 100% Sample *Note: For “B” Level Screening add “M” to part number, for “S” Level Screening add “S” to part number. See Part Number Designator. ** Note: Additional conformance inpsection testing, i.e. Group B,C & D optional. OMR7805SR OMR7812SR OMR7815SR OM7805STM OMR7805ST OMR7812ST OMR7815ST OM7805STM OMR7805NM OMR7812NM OMR7815NM Load Regulation OMR7805NH OMR7812NH OMR7815NH TYPICAL RADIATION CURVES Short Circuit Current 10.00 I = 5ma to 1.5 Amps load 3.00 2.50 8.00 Vin = 10v 2.00 1.50 Load Reg (mv) 6.00 Isc (A) 4.00 I = 25ma to 75ma load 1.00 Vin = 35v 2.00 0.50 0.00 0.00 1 10 100 1000 -2.00 1 10 100 1000 Radiation Total Dose (krads) Radiation Total Dose (krads) OM7805STM conditions: Vn= 7.5v to 20v i OM7805STM conditions:load = 5ma to 1Amp I Output Voltage 0.00 Line Regulation 4.992 4.990 -1.00 4.988 4.986 4.984 4.982 4.980 4.978 4.976 4.974 1 10 100 1000 -2.00 Line Reg (mv) Vout (V) -3.00 -4.00 -5.00 -6.00 1 10 OM7812STM conditions: = 5ma to 1.5Amps load I 14.00 Radiation Total Dose (krads) OM7812STM conditions:load = 5ma to 1Amp I 11.955 100 1000 Output Voltage Radiation Total Dose (krads) Load Regulation 12.00 11.950 10.00 11.945 Load Reg (mv Vout (V) 8.00 11.940 6.00 11.935 4.00 11.930 2.00 0.00 11.925 1 1 10 100 Radiation Total Dose (krads) 1000 10 100 1000 OM7812STM conditions: Vin = 19v 2.500 Radiation Total Dose (krads) OM7812STM conditions: Vin = 14.5v to 27v 2.00 Short Circuit Current Line Regulation 0.00 2.000 -2.00 Line Reg (mv) -6.00 Isc ( 1.000 0.500 0.000 1 10 100 1000 -4.00 1.500 -8.00 -10.00 -12.00 -14.00 1 10 100 1000 Radiation Total Dose (krads) Radiation Total dose (krads) OMR7805SR OMR7812SR OMR7815SR OMR7805ST OMR7812ST OMR7815ST OMR7805NM OMR7812NM OMR7815NM OMR7805NH OMR7812NH OMR7815NH TYPICAL RADIATION CURVES OM7815STM conditions: Vin = 17.5v to 30v Typical Line Regulation 15.15 OM7815STM conditions: Iload = 5ma to 1Amp Typical Voltage Output 0.00 -2.00 -4.00 -6.00 Line Reg (mv) 15.05 -10.00 -12.00 -14.00 -16.00 -18.00 -20.00 1 10 100 1000 Vout (vdc 14.95 14.85 1 10 100 1000 -8.00 Radiation Total Dose (k) Radiation Total Dose (k) OM7815STM conditions: Vin = 35V Typical Short Circuit Current 35.00 OM7815STM conditions: I 5ma to 1.5Amps load = Typical Load Regulat 1.00 0.90 30.00 0.80 25.00 0.70 0.60 (m 0.50 Load Reg. 20.00 Isc ( 15.00 0.40 0.30 10.00 0.20 5.00 0.10 0.00 0.00 1 10 100 1000 1 10 100 1000 Radiation Total Dose (k) Radiation Total Dose (k) OMR7805SR OMR7812SR OMR7815SR OMR7805ST OMR7812ST OMR7815ST OMR7805NM OMR7812NM OMR7815NM OMR7805NH OMR7812NH OMR7815NH TYPICAL PERFORMANCE CHARACTERISTICS PEAK OUTPUT CURRENT 3.5 3 2.5 DROPOUT VOLTAGE 100 RIPPLE REJECTION 80 Input To Output Differential (V) 2.5 2 1.5 Tj = 150°C Tj = 25°C 1.5 IOUT = 0A IOUT = 500mA Ripple Rejection (dB) Tj = -55°C 2 IOUT = 1A VOUT = 5V Output Current (A) 60 1 40 VIN - V = 8VDC + 3.5 Vrms IOUT = 1A Tj = 25°C 1 0.5 ∆VOUT = 100mV 0.5 ∆VOUT = 100MV 20 0 0 5 10 15 20 25 30 35 0 -75 -50 -25 0 25 50 75 100 125 150 0 10 100 1k 10k 100k Input To Output Differential (V) Junction Temperature (°C) Frequency (Hz) TYPICAL APPLICATIONS Fixed Output Regulator Circuit For Increasing Output Voltage INPUT OM78XX OM7662SC OUTPUT INPUT OM78XX OM7605SC VXX R1 OUTPUT 1µFt 0.1µF* 1µF IQ 0.1µF R2 *Increasing value of output capacitor improves system transient response. tRequired only if regulator is located an appreciable distance from power supply filter. VO = VXX (1+ R1 ) + IQ R2 R2 High Output Current, Short Circuit Protected Adjustable Output Regulator, 7 To 30 Volts INPUT R1 RSC INPUT OM7662SC OM78XX - OUTPUT OM78XX 1µF OUTPUT 1µF 0.33µF LM741 0.1µF 10K + OMR7805SR OMR7812SR OMR7815SR MECHANICAL OUTLINES .200 .190 .045 .035 OMR7805ST OMR7812ST OMR7815ST OMR7805NM OMR7812NM OMR7815NM OMR7805NH OMR7812NH OMR7815NH “T” P/N DESIGNATOR .420 .410 “H” P/N DESIGNATOR .150 .140 .665 .645 .537 .527 123 .430 .410 .038 MAX. .750 .500 .005 .035 .025 .100 TYP. .120 TYP. TO-257AA OMR78XXST Isolated/Front View Pin 1 Pin 2 Pin 3 Tab Input Ground Output Isolated Add “T” to part number for TO-257 Package TO-205AF (TO-39) OMR78XXNH Non-Isolated Pin 1 Input Pin 2 Output Pin 3 Ground (Case) Add “H” to part number for TO-205 Package “R” P/N DESIGNATOR “M” P/N DESIGNATOR .140 .450 .015 .050 .157 .140 .140 .050 1 2 .030 MIN. 123 .625 .415 3 .037 .375 TOP VIEW SIDE VIEW BOTTOM VIEW Hermetic D2 Pac OMR78XXSR Isolated Pin 1 Pin 2 Pin 3 Tab Front View - Input - Ground - Output - Isolated Add “R” to part number for D2 Pac Package OMR78XXNM SMD-1 Pin 1 - Input Pin 2 - Output Pin 3 - Ground Add “M” to part number for SMD (Surface Mount Package) OMR PART NUMBER DESIGNATOR (Example OMR7805STM) 7805 S T M Omnirel Rad-Tolerant Device Type Isolated Package Package Style Screening Level 205 Crawford Street, Leominster, MA 01453 USA (978) 534-5776 FAX (978) 537-4246 Visit Our Web Site at www.omnirel.com