PD110-42

PD110 13/11/02 3:25 pm Page 1 DC/DC Converters XPiQ inc. Intelligent Design Quality Product 110 Watts PD110 Series • Low Cost • 100% Burn-In • Small Size, Light Weight • Three Wide Input Ranges • Overvoltage Protection • Overcurrent Protection Specification All specifications typical at nominal line, full load and 25°C Input Input Voltage • 10 to 20 VDC (PD110 “L” series) 18 to 36 VDC (PD110 “M” series) 36 to 72 VDC (PD110 “H” series) 15A (rms) for 12 VDC 9.4A (rms) for 24 VDC 4.7A (rms) for 48 VDC General Efficiency Hold-up time Line Regulation Isolation Voltage • • • • 60% minimum 10 msec ±0.5% max. 1000 VDC from input to output Environmental Operating Temperature Storage Temperature MTBF Weight • • • • 0°C to +70°C* -40°C to +85°C 100,000 hours 670 g without cover Input Current • Output Output Voltage/ Current Ripple Overvoltage Protection Overcurrent Protection: Temperature Coefficient: • • • See rating chart 1% peak to peak maximum Provided on output #1 only, set at 112-132% of its nominal output voltage All outputs protected in short circuit conditions All outputs ±0.04%/°C maximum • • * Derate linearly from 100% load to 50°C to 50% load at 70°C 53 www.XP-iQ.com PH: 508 429.9883 FAX: 800 226.2100 Email: sales@xp-iq.com Holliston, MA 01746 USA • • PD110 13/11/02 3:25 pm Page 2 OUTPUT VOLTAGE & CURRENT RATINGS Output #1 Model PD110-10 PD110-12 PD110-13 PD110-14 PD110-16 PD110-23 PD110-31 PD110-32 PD110-40 PD110-41 PD110-42 PD110-45-1 PD110-45-2 PD110-46 Notes 1. 2. 3. 4. Vnom 5V 12 V 15 V 24 V 30 V +5 V +5 V +5 V +5 V +5 V +5 V +5 V +5 V +5 V Imin 0.0 A 0.0 A 0.0 A 0.0 A 0.0 A 0.8 A 0.8 A 0.8 A 0.8 A 0.8 A 0.8 A 0.8 A 0.8 A 0.8 A Imax 22.0 A 9.0 A 7.5 A 4.5 A 3.6 A 10.0 A 10.0 A 10.0 A 10.0 A 10.0 A 10.0 A 10.0 A 10.0 A 10.0 A Tol. 3% 2% 2% 2% 2% 3% 3% 3% 3% 3% 3% 3% 3% 3% Output #2 Vnom Imax (1) PD110 Output #3 Tol. Vnom Imin Imax Tol. Vnom Output #4 Imin Imax Tol. Maximum Output Power 110 W 110 W 110 W 110 W 110 W 110 W 110 W 110 W 110 W 110 W 110 W 110 W 110 W 110 W Ipeak +12 +12 +15 +12 +15 +12 +12 +24 +15 V V V V V V V V V 5 5 4 5 4 5 5 3 4 A A A A A A A A A 9.0 9.0 7.5 9.0 7.5 9.0 9.0 5.0 7.5 A A A A A A A A A 3% 3% 3% 3% 3% 3% 3% 5% 3% -12 -15 -12 -15 -12 -12 -12 -15 V V V V V V V V 0 0 0 0 0 0 0 0 A A A A A A A A 1 1 1 1 1 1 1 1 A A A A A A A A 4% 4% 4% 4% 4% 4% 4% 4% -5 +24 +12 +24 +12 -5 V V V V V V 0 0 0 0 0 0 A A A A A A 1 1 1 3 1 1 A A A A A A 4% 4% 4% 8% 4% 4% For output #2, minimum load is 0 A and peak current is shown for 10% maximum duty cycle for less than 60 seconds. PD110 “M” & “H” series is suitable for 110 watts maximum at 20 CFM forced air cooling or 80 watts maximum at convection cooling. PD110 “L” series is suitable for 90 watts maximum at 20 CFM forced air cooling or 70 watts maximum at convection cooling. Suffix codes for mechanical format and input range are as follows: PD110-XXYZ: “XX” is the model code from the above table. “Y” is the input range. (L=10-20VDC, M=18-36VDC, H=36-72VDC); “Z” is the mechanical format (A=open PCB, C=enclosed) EX: PD110-31MC, 18-36VDC input, enclosed form. • Pin Chart Model PD110-10, PD110-12 PD110-13, PD110-14 PD110-16 PD110-23 PD110-31, PD110-32 PD110-40, PD110-41 PD110-42, PD110-45-1 PD110-45-2, PD110-46 OUTPUT #1 OUTPUT #1 OUTPUT #1 COMMON RETURN COMMON RETURN COMMON RETURN COMMON RETURN COMMON RETURN COMMON RETURN OUTPUT #2 OUTPUT #2 OUTPUT #2 N.C. N.C. OUTPUT #3 OUTPUT #3 KEY OUTPUT #4 KEY N.C. N.C. N.C. KEY N.C. 1, 2, 3 OUTPUT #1 4, 5 RETURN 6, 7 RETURN 8, 9 OUTPUT #1 10 N.C. 11 N.C. 12 KEY 13 N.C. Mechanical Details OPEN PCB “A” ENCLOSED “C” Dimensions shown in inches (mm). Tolerance 0.02 (0.5) maximum. Input connector mates with Molex housing 09-50-3051 and Molex 2878 series crimp terminal. Output connector mates with Molex housing 09-50-3131 and Molex 2878 series crimp material. www.XP-iQ.com PH: 508 429.9883 FAX: 800 226.2100 Email: sales@xp-iq.com Holliston, MA 01746 USA 54