SP0103NC3

Document: SP0103N Last Revision Date: 09-2003 Product Specification: SP0103 Series with Integrated Amplifier This document applies the following SiSonic Model Numbers: SP0103NC3-2 SP0103NC3-3 SiSonic microphone with integrated amplifier offers designers numerous features: up to 20dB gain, surface-mountable, compatible with standard solder reflow, pick-and-place with standard high speed automated equipment, low output impedance, and excellent environmental characteristics. External amplifiers amplify both signal and external noise induced in the circuit, compared to SiSonic SP0103 that amplifies the signal prior to external noise. Microphone Dimensional Layout Item Height Length Width Weight Coplanarity Dim. 1.45 6.15 3.76 < 0.5 < 0.1 Tol. (+/-) 0.15 0.05 0.05 Units mm mm mm grams mm Microphone Pin Output Recommended PCB Land Layout Knowles Acoustics www.knowlesacoustics.com 1 Document: SP0103N Last Revision Date: 09-2003 Product Specifications Test Conditions: +20ºC, 60-70% R.H. Limits Symbol Directivity Sensitivity Output impedance Current Consumption Signal to Noise Ratio Typical Input Referred Noise Supply Voltage Sensitivity Loss across Voltage Maximum Input Sound Level S ZOUT IDSS S/N ENL Vs Change in sensitivity over 5.5v to 1.5v Condition Omni-directional @ 1kHz (0dB=1V/Pa) where R3=0Ω, C1=0.47uF @ 1kHz (0dB=1V/Pa) across 1.5 to 5.5 volts @ 1kHz (0dB=1V/Pa) A-weighted 1.5 0.100 55 59 35 5.5 -26 -22 -18 100 0.350 dB Ω mA dB dBA SPL Min. Nom. Max. Unit V dB dB No Change Across Voltage Range At 100dB SPL, THD < 1% At 115dB SPL, THD < 10% -40 -40 100 – 10,000 +100 +100 Operating Temperature Storage Temperature Frequency Range ºC ºC Hz Frequency Response Curve Knowles Acoustics www.knowlesacoustics.com 2 Document: SP0103N Last Revision Date: 09-2003 Packaging Specifications Carrier – Tape Detail Model Number SP0103NC3 SP0103NC3 Suffix Reel Diameter 7” 13” Qty per Reel 1,200 4,500 Capacitor Config. 10 & 33pF 10 & 33pF Tape & Reel Leader Length Label Available in 7” or 13” diameter. 800mm or minimum of 100 empty pockets Label applied to external package and direct to reel. Per JEDEC. 1 year storage (original packaging, low humidity) “L” – direction -2 -3 NOTE: All devices are lead-free and compatible with leadfree reflow profile. Storage Life Polarity of part Solderability Characteristics Solder Reflow Terminal Pads # of Reflow Passes Solder Reflow Profile (Maximum Conditions) (** No board washing after reflow **) 260ºC for maximum 30 seconds Gold (27u”) over Nickel (150u”) Typical reference Reliability section Knowles Acoustics www.knowlesacoustics.com 3 Document: SP0103N Last Revision Date: 09-2003 Reliability Thermal Shock High Temperature Storage Test Low Temperature Storage Test High Temperature Operating Test Low Temperature Operating Test Humidity Test Vibration Test Microphone unit must operate when exposed to air-to-air thermal shock 100 cycles, from –40ºC to +125ºC. (IEC 68-2-4) Microphone unit must maintain sensitivity after storage at +105ºC for 1,000 hours. (IEC 68-2-2 Test Ba) Microphone unit must maintain sensitivity after storage at –40ºC for 1,000 hours. (IEC 68-2-1 Test Aa) Microphone unit must operate within sensitivity specifications for 16 hours at 105ºC. (IEC 68-2-2 Test Ba) Microphone unit must operate within sensitivity specifications for 16 hours at –40ºC. (IEC 68-2-1 Test Aa) Tested under Bias at 85ºC/85% R.H. for 270 hours. (JESD22-A101A-B) Microphone unit must operate under test condition: 4 cycles, from 20 to 2,000 Hz in each direction (x,y,z), 48 minutes, using peak acceleration of 20g (+20%, -0%). (MIL 883E, method 2007.2, A) Tested to 8kV direct contact discharge or 15kV air discharge as specified by IEC 1000-4-2, level 3 and level 4. Microphone is tested to 5 passes through reflow oven, with microphone mounted upside-down under conditions of 260ºC for 30 seconds maximum. Tested to greater than 5,000g (IEC 68-2-27, Ea). After test conditions are performed, the sensitivity of the microphone shall not deviate more than 3dB from its initial value. Electrostatic Discharge Reflow Mechanical Shock Note: Knowles Acoustics www.knowlesacoustics.com 4 Document: SP0103N Last Revision Date: 09-2003 Recommended Interface Circuit for SP0103N Integrated Amplifier V+ Term 4 = Vdd Vout Term 1 = Output R1 = 22kΩ R2 = 2.4kΩ Term 3 = Ground Term 2 = Gain Control R3 (set by customer) C1 (set by customer) Desired Gain Unity Gain (0dB) 20dB Gain Adjustable Gain Pin 2 Termination Method Tie Terminal 2 directly to Output (Terminal 1). Tie Terminal 2 through C1 (0.47uF) to Ground. Add R3 and C1. Use formulas provided to calculate settings, or contact Knowles for support. Setting Gain Formulas: Gain of non-inverting Op-Amp is determined as: G=1+ {R1 / (R2 + R3)} Gain(dB) = 20 * log(G) High-pass-filter Corner Frequency: C.F. = 1 / {2*pi*(R2 + R3) * C1} Knowles Acoustics www.knowlesacoustics.com 5