WRA1215P-3W

WRAP-3W Series WIDE INPUT ISOLATED & REGULATED 3W OUTPUT DUAL OUTPUT MINIATURE DIP PACKAGE FEATURES ● Wide (2:1) Input Range ● Efficiency to 82% ● Operating Temperature: -40°C~+85°C ● 1KVDC Isolation ● Dual Output ● UL94-V0 Package ● No Heat sink Required ● Industry Standard Pin out ● MTBF>1,000,000 hours ● Custom Service Available PRODUCT PROGRAM Part Number WRA0505P-3W WRA0509P-3W WRA0512P-3W WRA0515P-3W WRA1205P-3W WRA1209P-3W WRA1212P-3W WRA1215P-3W WRA1505P-3W WRA1509P-3W WRA1512P-3W WRA1515P-3W WRA2405P-3W WRA2409P-3W WRA2412P-3W WRA2415P-3W WRA4805P-3W WRA4809P-3W WRA4812P-3W WRA4815P-3W Input Output Voltage (VDC) Voltage Current (mA) Nominal Range Max* (VDC) Max Min 5 5 5 5 12 12 12 12 15 15 15 15 24 24 24 24 48 48 48 48 4.5~9VDC 4.5~9VDC 4.5~9VDC 4.5~9VDC 9~18VDC 9~18VDC 9~18VDC 9~18VDC 12~24VDC 12~24VDC 12~24VDC 12~24VDC 18~36VDC 18~36VDC 18~36VDC 18~36VDC 36~72VDC 36~72VDC 36~72VDC 36~72VDC 11 11 11 11 22 22 22 22 30 30 30 30 40 40 40 40 80 80 80 80 ±5 ±9 ±12 ±15 ±5 ±9 ±12 ±15 ±5 ±9 ±12 ±15 ±5 ±9 ±12 ±15 ±5 ±9 ±12 ±15 300 165 125 100 300 165 125 100 300 165 125 100 300 165 125 100 300 165 125 100 30 16 12 10 30 16 12 10 30 16 12 10 30 16 12 10 30 16 12 10 Efficiency (%, Typ) 65 67 70 72 72 73 77 79 75 79 80 81 78 80 81 82 76 81 81 82 Package Style DIP DIP DIP DIP DIP DIP DIP DIP DIP DIP DIP DIP DIP DIP DIP DIP DIP DIP DIP DIP APPLICATIONS The WRAP-3W Series are specially designed for applications where a wide range input voltage power supplies are isolated from the input power supply in a distributed power supply system on a circuit board. These products apply to: 1) Where the voltage of the input power supply is wide range (voltage range: 2:1); 2) Where isolation is necessary between input and output (isolation voltage =1000VDC); 3) Where the regulation of the output voltage and the output ripple noise are demanding. These products don’t apply to: 1) Where the input voltage t is required to be more than 2:1; 2) Where the isolation voltage between input and output is required to be >1000VDC; 3) The output load’s actual power consumption is less than 1W, otherwise our company’s WRAP-1W/0.5W series are recommended. ISOLATION SPECIFICATIONS Item Isolation voltage Isolation resistance Test conditions Flash tested for 60 seconds Test at 500VDC Min 1000 1000 Typ Max Units VDC MΩ OUTPUT SPECIFICATIONS Item 3W output power Positive Voltage accuracy Negative Voltage accuracy Load regulation Line regulation Temperature drift (Vout) Ripple Noise Switching frequency Test conditions See below products program Refer to recommended circuit Refer to recommended circuit From 10% to 100% load Input Voltage From Low to High Refer to recommended circuit 20Hz-300KHz bandwidth DC-20MHz bandwidth 100% load，nominal input voltage 10% load，nominal input voltage Min 0.3 Typ ±1 ±3 ±0.1 ±0.2 30 80 80 250 Max 3 ±3 ±5 ±0.2 ±0.5 0.03 60 150 200 600 Units W % %/°C mVp-p KHz MODEL SELECTION WRA0505P-3W Rated Power Package Style Output Voltage Input Voltage Product Series MORNSUN Science& Technology Ltd. Address: 8th floor 8th building, Huangzhou Industrial District, Guangzhou, China Tel: 86-20-85571041 Fax: 86-20-85536272 Http://www.mornsun.cn/ Note: 1.All specifications measured at TA=25°C, humidity1,000,000 hours Vin GN D C +V o DC DC L L C C 0V -Vo Vn i GN D C +Vo C C DC DC （Figure 1) C CL 0V -Vo ***Lead Temperature 1.5mm from case for 10 seconds. TYPICAL CHARECTERISTICS supply and the rippled voltage do not exceed the module standard. Input current of power supply should afford the startup current of this kind of DC/DC module. (See figure 2) External Capacitor Although this series of DC/DC converter can work without external capacitor, in order to keep an optimum performance, however, it needs external capacitor. (See Table 1) FOOTPRINT DETAILS Bottom View Pin 2,3 23 9 1011 Requirement on Output Load WRAP Series GND NC +Vo -Vo 0V Vin 10,15 14 11 To ensure this module operate efficiently and reliably, a minimum load is specified for this kind of DC/DC converter in addition to a maximum load (namely full load). During operation, make sure the specified range of input voltage is not exceeded, the minimum out put load is not less than 10% Of the full load, and that this product should never be operated under no load!!! If the actual load is less below the specified minimum load，the output ripple of this type of DC/DC converter will increase drastically and at the same time efficiency & reliability of the circuit will decrease deeply .If the actual output power from the load in your circuit is very small ， please connect a resistor with proper resistance at the output end to in parallel to increase the load, or use our company’s other products with a lower rated output power. 2322 16 1514 9,16 22,23 OUTLINE DIMENSIONS & RECOMMENDED FOOTPRINT 31.80 0.50 20.30 23 22 1615 14 9.45 23 9 10 11 The products cannot be used in parallel and in plug and play. 15.24 External Capacitor Table(Table 1) Vin 5V & 12V 24V & 48V Cin 100uF Cout (0+70°C) 100uF (electrolytic capacitor) Cout (-40+85°C) 47uF (tantalum capacitor) 2.54 22.86 2 x 2.54 4.00 10uF (Bottom View) (Side View) Note: All Pins on a 2.54mm pitch; All Pin diameters are 0.50 mm(Tolerance:±0.25); All dimensions in mm. The dimensions of the WRAP series are correspondent with the WRBP series. APPLICATION NOTE Recommended Circuit All the WRA-3W Series have been tested according to the following recommended testing circuit before leaving factory. This series should be tested under load. Never be tested under no load (See Figure 1 & 2). If you want to further decrease the input/output ripple, you can increase capacitance properly or choose capacitors with low ESR. However, the capacitance should not be too high.(See table 1).If you want to use the products in high EMI, please choose our metal packaged products. MORNSUN Science& Technology Ltd. Input Current When it is used in unregulated power supply，be sure that the fluctuating range of the power Address: 8th Floor 8th Building, Huangzhou Industrial District, Guangzhou, China Tel :86-20-85571041 Fax:86-20-85536272 Http:// www.mornsun.cn/ Edition: Preliminary / Page 2 of 2