A05D12

A and F SERIES Single and dual output Recommended for new design-ins • • • • • • • Low noise Linear regulation Six sided shield Pi input filter Short circuit protected High Isolation Meets EN55022 and VDE0871 level B conducted noise [ 2 YEAR WARRANTY ] The A and F Series offer high input/output isolation of 500VDC with only 1mV rms (40mV pk-pk) output ripple and noise. Other premium performance features include line and load regulation of less than ±0.1% and efficiencies of up to 69%. The converters are encapsulated in a 2 x 2 inch industry standard package with a 0.38 inch profile. The six sided copper case allows optimum thermal conductivity and provides shielding for EMI/RFI suppression. A Pi input filter reduces reflected ripple. Reliable operation is assured through the use of efficient, design-derated components and by heatsinking all dissipating elements directly to the metal case. This permits operation from -25oC to +71oC with no derating or additional heatsinking required. A and F Series DC/DC converter are suitable for a wide range of general industrial applications, especially where low noise levels are required. SPECIFICATION OUTPUT SPECIFICATIONS Line regulation Load regulation Cross regulation Ripple and noise Transient response All specifications are typical at nominal input, full load at 25°C unless otherwise stated ELECTROMAGNETIC COMPATIBILITY SPECIFICATIONS ±0.07%, max. ±0.1%, max ±0.07% ±0.1% Conducted noise EN55022, EN55011, FCC Class B HL to LL, A series FL to NL, F series GENERAL SPECIFICATIONS A series, FL-NL, all outputs F series, FL-NL, dual output Voltage balance, duals 5Hz to 20MHz A series: FL to NL F series: FL to NL F series: FL to 50% FL Temperature coefficient Overvoltage protection Short circuit protection Efficiency Isolation Voltage Switching frequency Case Material ±0.1% max. dev., 50µs recovery ±0.5% max. dev., 75µs recovery ±0.5% max. dev., 25µs recovery ±0.01%/°C, max. F series, 5 Volt output models only 6.8VDC Relative humidity Altitude See table on facing page See Note 5 (6) 63% min. Input/Output Fixed 500VDC 20kHz Black coated copper with non-conductive base 50g (1.77oz) MIL-HDBK-217E 680,000 hours ±1.0%, max 40mV pk-pk, max. 1mV rms, max. Weight MTBF ENVIRONMENTAL SPECIFICATIONS Temperature Operating ambient -25°C to +71oC Non-operating –55°C to +85°C Case +95oC, max. Derating None required Cooling Free-air convection Non-condensing Operating Non-operating 5% to 95% RH 10,000 feet max. 40,000 feet max. A series, output to common 150% Iout F series, output to common 160% Iout INPUT SPECIFICATIONS Input voltage range Input filter Pi network INPUT VOLTAGE RANGES NOMINAL INPUT 5VDC 48VDC A SERIES 4.75 to 5.25V 42.0 to 56.0V F SERIES 4.75 to 5.5V PAGE 1 INPUT DC/DC CONVERTERS | 5W DC/DC 5 Watt Nominal input DC/DC converters INPUT VOLTAGE 5VDC 48VDC 5VDC OUTPUT VOLTAGE ±12VDC ±15VDC 5VDC OUTPUT CURRENT ±150mA ±150mA 1000mA INPUT CURRENT NO LOAD 150mA 20mA 130mA FULL LOAD 1150mA 135mA 1500mA REGULATION (1) MODEL EFFICIENCY (3) LINE (MAX.) (2) LOAD (MAX.) ±0.07% ±0.07% ±0.1% ±0.07% ±0.07% ±0.1% NUMBER 63% 69% 67% A05D12/150Z A48D15/150Z F05S05/1000Z Notes 1 2 3 4 5 6 Maximum. Measured from high line to low line. Measured from full load to no load. The A series case is connected to output common for all input voltages except 48V when it is connected to + input. Fixed frequency design provides for easier input filtering and better noise performance. The input voltage range can be increased to 10% under reduced loads. Please contact the factory for details. PIN CONNECTIONS PIN 1 2 3 4 5 A SERIES + Input – Input + Output Common – Output (4) F SERIES + Input – Input + Output No Pin – Output CASE Z 2.00 (50.80) 0.38 ± 0.01 (9.50) 0.040 Dia. (1.000) 3 0.500 (12.700) 0.300 (7.600) 4 5 2.00 (50.80) 0.800 (20.300) BOTTOM VIEW 1 2 0.60 (15.20) 0.100 (2.500) 0.90 (22.90) ±0.04 ±0.005 0.22 Min. (5.60) 0.200 (5.100) Tolerance .xx = .xxx = http://www.artesyn.com PAGE 2