AMC DOC. #:AMC8878_D (LF) March 2004
ADD MICROTECH CORP.
DESCRIPTION
AMC8878/8879
LOW NOISE 150mA LOW DROPOUT REGULATOR
FEATURES
The AMC8878/8879 series is a low noise, low dropout linear regulator operating from 2.5V to 6.5V input. An external capacitor can be connected to the bypass pin to lower the output noise level to 30µVRMS. Designed with a P-channel MOSFET output transistor, the AMC8878/8879 consume a low supply current, independent of the load current and dropout voltage. The internal thermal shut down circuit will limits the junction temperature to below 150°C. Other features include thermal protection, reverse battery protection and output current limit. Both AMC8878 and AMC8879 come in a miniature 5-pin SOT-23 package.
Low output noise: 30µVRMS Industry standard’2982 pin assignment (AMC8878) Output voltage precision of ±1.4% accuracy Very low dropout voltage: 50mV/50mA and 165mV/150mA On/Off control Low IQ: 1.6µA Short circuit protection Internal thermal overload protection Available in surface mount 5-pin SOT-23 package. Enhanced pin-to-pin Compatible to the MAX8878 (AMC8878) and TK111xxS (AMC8879) series.
APPLICATIONS
PACKAGE PIN OUT
VIN VOUT SHDN 1 GND 2
4 5 VIN
Cellular Telephones Battery Powered Systems Hand-Held Instruments Pagers Personal Data Assistance (PDA) PCMCIA Cards
1
5
GND 2 SHDN 3 BP
BP 3
4 VOUT
AMC8878
AMC8879
5-Pin Plastic SOT-23 Surface Mount (Top View) ORDER INFORMATION Plastic SOT-23 5-pin 0OC ≤ TA≤ 70OC AMC8878-X.XDBT 0OC ≤ TA≤ 70OC AMC8878-X.XDBTF(Lead Free) Temperature Range
DBT
Plastic SOT-23 5-pin AMC8879-X.XDBT AMC8879-X.XDBTF(Lead Free)
DBT
EXPANDED ORDER INFORMATION Device Name AMC8870.2-ڤDBT AMC8875.2-ڤDBT AMC8878.2-ڤDBT AMC88758.2-ڤDBT AMC8870.3-ڤDBT AMC8872.3-ڤDBT AMC8873.3-ڤDBT AMC8870.5-ڤDBT Output Voltage 2.0V 2.5V 2.8V 2.85V 3.0V 3.2V 3.3V 5.0V
1
Symbolization AMC8878 AB20 AB25 AB28 AB2U AB30 AB32 AB33 AB50 AMC8879 AC20 AC25 AC28 AC2U AC30 AC32 AC33 AC50
www.addmtek.com
Copyright 2002, ADD Microtech Corp.
AMC DOC. #: AMC8878_D (LF) March 2004
AMC8878/8879
LOW NOISE 150mA LOW DROPOUT REGULATOR
TYPICAL APPLICATION
VIN 2.5V to 6V
VOUT CIN 1µF
AMC8878 AMC8879
COUT 1µF
ON OFF
CBP 0.01µF
ABSOLUTE MAXIMUM RATINGS (Note) 12V Input Voltage, VIN 150 OC Operating Junction Temperature, TJ Storage Temperature Range -65 OC to +150 OC Lead Temperature (soldering, 10 seconds) +260 OC O Power Dissipation, PD @ TA = 70 C 150 mW Note: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of the specified terminal. THERMAL DATA DB PACKAGE: Thermal Resistance from Junction to Ambient, θ JA Junction Temperature Calculation: TJ = TA + (PD × θ JA). The θJA numbers are guidelines for the thermal performance of the device/pc-board system. Connect the ground pin to ground using a large pad or ground plane for better heat dissipation. All of the above assume no ambient airflow. Maximum Power Calculation: T – TA(MAX) PD(MAX)= J(MAX) θJA TJ(OC): Maximum recommended junction temperature TA(OC): Ambient temperature of the application θJA(OC /W): Junction-to-junction temperature thermal resistance of the package, and other heat dissipating materials. The maximum power dissipation for a single-output regulator is : PD(MAX) = [(VIN(MAX) - VOUT(NOM))] × IOUT(NOM) + VIN(MAX) × IQ Where: VOUT(NOM) = the nominal output voltage IOUT(NOM) = the nominal output current, and IQ = the quiescent current the regulator consumes at IOUT(MAX) VIN(MAX) = the maximum input voltage Then θJA = (+150 OC – TA)/PD
220 OC /W
Copyright 2002, ADD Microtech Corp.
2
www.addmtek.com
AMC DOC. #: AMC8878_D (LF) March 2004
AMC8878/8879
LOW NOISE 150mA LOW DROPOUT REGULATOR
BLOCK DIAGRAM
VIN
Reverse Battery Protection
SHDN
Shutdown And Power-On Control Current Limit
VOUT
Thermal Sensor
VREF
GND BP
PIN DESCRIPTION Pin Number AMC8878 AMC8879 1 5 2 2 3 4 5 1 3 4 Pin Name VIN GND SHDN BP VOUT Pin Function Input Ground Logic control shutdown pin; HI: Device is ON, LO: Device is OFF Noise bypass pin; The output noise level can be reduced to 30µVRMS by connecting external capacitors Output
Copyright 2002, ADD Microtech Corp.
3
www.addmtek.com
AMC DOC. #: AMC8878_D (LF) March 2004
AMC8878/8879
LOW NOISE 150mA LOW DROPOUT REGULATOR
Units V mA µF µF
RECOMMENDED OPERATING CONDITIONS Recommended Operating Conditions Parameter Symbol Min. Typ. Max. Input Voltage VIN 2.5 6.5 Load Current IO 5 150 Input Capacitor (VIN to GND) 1.0 Output Capacitor with ESR of 10Ω max., (VOUT to GND) 1.0
Note: 1. CIN: A 1.0 µF capacitor (or larger) should be placed between VIN to GND. 2. COUT: A 1.0 µF (or larger) capacitor is recommended between VOUT and GND for stability. The part may oscillate without the capacitor. Any type of capacitor can be used, but not Aluminum electrolytics when operating below -25 OC, The capacitance may be increased without limit.
ELECTRICAL CHARACTERISTICS Unless otherwise specified, these specifications apply over the operating ambient temperature of 0°C to +70 °C with VIN = VOUT(NOMIAL) + 0.5V, and are for DC characteristics only. (Low duty cycle pulse testing techniques are used which maintains junction and case temperatures equal to the ambient temperature.) Parameter Output Voltage Accuracy Maximum Output Current Current Limit Ground Pin Current Symbol ∆VOUT IOUT ILIMIT IQ IOUT = 0mA IOUT = 150mA IOUT = 1mA IOUT = 50mA IOUT = 150mA VIN = (VOUT + 0.1V) to 6.5V, IOUT = 1mA -0.15 IOUT = 0 to 120mA, COUT = 1µF f = 10Hz - 100KHz, CBP = 0.01µF VIN = 2.5V to 5.5V VIN = 2.5V to 5.5V VOUT = 0V VSHDN = VIN TA = +25 OC TA = +85 OC TA = +25 OC TA = +85 OC TA = +25 OC TA = +85 C
O
Test Conditions IOUT = 0mA, TA = +25 OC IOUT = 0 to 150mA
AMC8878/8879
Min -1.4 -3 150 160
Typ.
Max +1.4 +2
Units % mA mA
Dropout Voltage Line Regulation Load Regulation Output Voltage Noise ∆VOI ∆VOL en
COUT = 10µF COUT = 100µF 2.0
1.6 1.7 1.1 50 165 0 0.01 30 20
10
µA
120 0.15 0.04
mV %/V %/mA µVRMS V V µA nA
Shutdown Input Threshold High Shutdown Input Threshold Low Shutdown Supply Current Shutdown Input Bias Current
VSIH VSIL IQ(SHDN) ISHDN
0.01 0.2 0.01 0.5 6 6 +150
0.4 1 100
Shutdown Exit Delay Thermal Shutdown Temperature
tdelay TSHDN
CBP = 0.1µF, COUT = 1µF, No load
ms
O
C
Note: 1. Current limit is measured at constant junction temperature, using pulse ON time. 2. Dropout is measured at constant junction temperature, using pulse ON time, and criterion is VOUT inside target value ± 2 %. 3. Regulation is measured at constant junction temperature, using pulsed ON time.
Copyright 2002, ADD Microtech Corp.
4
www.addmtek.com
AMC DOC. #: AMC8878_D (LF) March 2004
AMC8878/8879
LOW NOISE 150mA LOW DROPOUT REGULATOR
Characterization Curves VIN=VOUT(NOMINAL) + 0.5V or 2.5V(whichever is greater), CIN=1uF, COUT=1uF,CBP=0.01uF, TA=+25 O C, ,Using plused ON time,unless otherwise noted.
Output Voltage v.s. Output Current
3.5
Quiescent Current v.s. Output Current
2
Output Voltage(V)
3.4
Quiescent Current (µA)
VOUT=3.3V
3.3
1.8 1.6 1.4 1.2 1 0.8 0.6 0.4 0.2 0
3.2
3.1
3
2.9
2 .8 0 20 40 60 80 100 120 140
0
25
50
75
100
125
150
Output Current (V)
Output Current (mA)
Output Voltage v.s. Input Voltage
3.5
Quiescent Current v.s. Input Voltage
2.4
Output Voltage (V)
3.4
Quiescent Current (µA)
IO=10mA
VOUT=3.3V
2.2 2 1.8 1.6 1.4 1.2
3.3
IO=150mA
3.2
IO=150mA
3.1
3 4 4.5 5 5.5 6
IO=10mA
4 4 .5 5 5 .5 6
Input Voltage (V)
1
Input Voltage (V)
Output Voltage v.s. Temperature
3. 48
Quiescent Current v.s. Temperature
2.4
Quiescent Current (µA)
105
VOUT=3.3V
2.2 2 1.8 1.6 1.4 1.2 1
Output Voltage (V)
3. 44 3. 4 3. 36 3. 32 3. 28 3. 24 3. 2 25 45 65 85
IO=10mA
IO=150mA
25
45
65
85
105
Temperature (OC)
Temperature (OC)
Copyright 2002, ADD Microtech Corp.
5
www.addmtek.com
AMC DOC. #: AMC8878_D (LF) March 2004
AMC8878/8879
LOW NOISE 150mA LOW DROPOUT REGULATOR
Characterization Curves (Continued)) VIN=VOUT(NOMINAL) + 0.5V or 2.5V(whichever is greater), CIN=1uF, COUT=1uF,CBP=0.01uF, TA=+25 O C, ,Using plused ON time,unless otherwise noted.
Dropout Voltage v.s. Output Current
0.24
Dropout Voltage v.s. Temperature
0.3
Dropout Voltage (V)
Dropout Voltage (V)
0.22 0.2 0.18 0.16 0.14 0.12 0.1 0.08 0.06 0.04 0.02 0 0 25 50 75 100 125 150
IO=150mA
0.25
0.2
0.15
0.1
0.05
0 25 45 65 85 105
Output Current (mA)
Temperature ( C)
O
Load Transient Response with IO=50mA
25mA/ Div 75mA/ Div
COUT=1uF
Load Transient Response with IO=150mA
COUT=1uF
IO VO
IO VO
50mV/ Div
50mV/ Div
Time=2ms
Time=2ms
Line Transient Response, With IO=50mA
1V/ Div 2V/ Div
VOUT=3.3V
Entering Shutdown, No Load
VSHDN
0.5V/ Div
1V/ Div
VOUT
Time=1ms
Copyright 2002, ADD Microtech Corp. 6
Time=2ms
www.addmtek.com
AMC DOC. #: AMC8878_D (LF) March 2004
AMC8878/8879
LOW NOISE 150mA LOW DROPOUT REGULATOR
Characterization Curves (Continued)) VIN=VOUT(NOMINAL) + 0.5V or 2.5V(whichever is greater), CIN=1uF, COUT=1uF,CBP=0.01uF, TA=+25 OC, Using plused ON time,unless otherwise noted.
Shutdown Exit Delay, CBP= 0.1uF
Shutdown Exit Delay, CBP= 2pF
2V/ Div
1V/ Div
1V/ Div
VOUT
IO=50mA VOUT=3..3V
2V/ Div
VSHDN
VSHDN
VOUT
IO=50mA VOUT=3..3V
Time=2ms
Time=200µs
Copyright 2002, ADD Microtech Corp.
7
www.addmtek.com
AMC DOC. #: AMC8878_D (LF) March 2004
AMC8878/8879
LOW NOISE 150mA LOW DROPOUT REGULATOR
SEATING PLANE
5-Pin SOT-23
D b L L1
INCHES MIN A 0.012 0.003 A1 b c
e e1
GAUGE PLANE
MILLIMETERS MAX 0.057 0.006 0.051 0.020 0.009 MIN 0.90 0.30 0.08 TYP 1.15 2.90 BSC 2.80 BSC 1.60 BSC 0.95 BSC 1.90 BSC 0.024 0.30 0.45 0.60 REF 0.25 BSC 15° 5° 10° 15° 0.60 MAX 1.45 0.15 1.30 0.50 0.22
TYP 0.045 -
E
E1
A2 0.035
c
L2
D E E1 e e1 L L1
0.114 BSC 0.110 BSC 0.063`BSC 0.037 BSC 0.075BSC 0.012 0.018 0.024 REF 0.010 BSC 5° 10°
M
A
A2
A1
M
L2 °M
Copyright 2002, ADD Microtech Corp.
8
www.addmtek.com
AMC DOC. #: AMC8878_D (LF) March 2004
AMC8878/8879
LOW NOISE 150mA LOW DROPOUT REGULATOR
IMPORTANT NOTICE
ADD Microtech (ADDM) reserves the right to make changes to its products or to discontinue any integrated circuit product or service without notice, and advises its customers to obtain the latest version of relevant information to verify, before placing orders, that the information being relied on is current. A few applications using integrated circuit products may involve potential risks of death, personal injury, or severe property or environmental damage. ADDM integrated circuit products are not designed, intended, authorized, or warranted to be suitable for use in life-support applications, devices or systems or other critical applications. Use of ADDM products in such applications is understood to be fully at the risk of the customer. In order to minimize risks associated with the customer’s applications, the customer should provide adequate design and operating safeguards. ADDM assumes to no liability to customer product design or application support. ADDM warrants the performance of its products to the specifications applicable at the time of sale.
U.S.
ADD Microtech Inc. 492 Altamont Drive Milpitas, CA 95035 T E L : (408) 9410420 F A X : (408) 9410864
Asia Pacific region
ADD Microtech Corp 13F, NO. 287, Sec. 3, Nan Jing E. Rd., Taipei, Taiwan 105 T E L : 2-27132800 F A X : 2-27132805
Copyright 2002, ADD Microtech Corp.
9
www.addmtek.com