ATR-S0105

155Mbps Single Mode SFP Transceiver (80km) ATR-S0105 Features a. Single Power Supply 3.3V b. Small Form Factor Pluggable (SFP) MSA compatible c. LVPECL Compatible Signal Interface d. Duplex LC Connector Applications a. ATM Switches and Routers c. SONET/SDH Switches Infrastructure d. Fast Ethernet Application Absolute maximum ratings Parameter Storage Temperature Operating Temperature Supply Voltage Voltage at any Input Pin Symbol TS Top VCC VIN Min. -40 0 -0.5 0 Max. +85 +70 +3.6 Vcc Unit ℃ ℃ V V Operating Conditions Transmitter（T=0 to +70℃, VCC =3.13~3.47V） Parameter Central Wavelength Spectral Width(-20dB) Side Mode Suppression Ratio Output Power Extinction Ratio Optical Rise/Fall Time Differential Input Voltage Tx Disable Input Voltage_Low Tx Disable Input Voltage_High Transmit Fault Output-Low Transmit Fault Output-High Parameter Wavelength Range MIN. Input Power (Sensitivity) MAX. Input Power (Saturation) Signal Detect-Asserted Signal Detect-Deasserted Symbol λC Δλ SMSR Po ER Tr/Tf VIH- VIL TDIS, L TDIS, H TX_FAULTL TX_FAULTH Symbol λ PMIN PMAX PA PD Min. 1480 30 -5 10 500 0 2.0 0 2.0 Min. 1100 -3 -45 Typ. 0 2 2000 0.5 Vcc 0.8 VCC Max. 1600 -34 -34 dBm dB ns mV V V V V Unit nm dBm dBm dBm dBm Typ. 1550 Max. 1580 1 Unit nm nm Receiver （T=0 to +70℃, Vcc=3.13~3.47V (+3.3V) No. 8, Jingwu Road Ding Mao Development Zone Zhenjiang 212009, China Tel: (86)511-8885688(5088) Fax: (86)511-8889135 Email: sales@allrayinc.com, marketing@allrayinc.com 155Mbps Single Mode SFP Transceiver (80km) ATR-S0105 Signal Detect Hysteresis Return Loss Differential Output Voltage Receiver Loss of Signal Output Voltage-Low Receiver Loss of Signal Output Voltage-High PHYS ORL VOH- VOL RX_LOSL RX_LOSH 0 2.0 0.8 VCC V V 1 12 dB dB Block Diagram of Transceiver Pin Assignment and Function Definitions It is the responsibility of the system integrator to assure that no thermal, energy, or voltage hazard exists during the hot-plug-unplug sequence. It is also the responsibility of the system integrator and end-user to minimize static electricity and the probability of ESD events by careful design. SFP Transceiver Electrical Pad Layout No. 8, Jingwu Road Ding Mao Development Zone Zhenjiang 212009, China Tel: (86)511-8885688(5088) Fax: (86)511-8889135 Email: sales@allrayinc.com, marketing@allrayinc.com 155Mbps Single Mode SFP Transceiver (80km) ATR-S0105 Pins Assignment Function definition Pin No. Name VeeT 1 TX Fault 2 TX Disable 3 MOD-DEF2 4 MOD-DEF1 5 MOD-DEF0 6 Rate Select 7 LOS 8 VeeR 9 VeeR 10 VeeR 11 RD12 RD+ 13 VeeR 14 VccR 15 VccT 16 VeeT 17 TD+ 18 TD19 Function Transmitter Ground Transmitter Fault Indication Transmitter Disable Module Definition 2 Module Definition 1 Module Definition 0 Not Connected Loss of Signal Receiver Ground Receiver Ground Receiver Ground Inv. Received Data Out Received Data Out Receiver Ground Receiver Power Transmitter Power Transmitter Ground Transmit Data In Inv Transmit Data In Plug Seq. 1 3 3 3 3 3 3 3 1 1 1 3 3 1 2 2 1 3 3 Notes Note 1 Note 2 Note 3 Note 3 Note 3 Note 4 Note 5 Note 5 Note 6 Note 6 No. 8, Jingwu Road Ding Mao Development Zone Zhenjiang 212009, China Tel: (86)511-8885688(5088) Fax: (86)511-8889135 Email: sales@allrayinc.com, marketing@allrayinc.com 155Mbps Single Mode SFP Transceiver (80km) ATR-S0105 VeeT Transmitter Ground 1 20 Notes: 1. TX Fault is an open collector output, which should be pulled up with a 4.7K~10K. resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; logic 1 indicates a laser fault of some kind. In the low state, the output will be pulled to less than 0.8V. 2. TX Disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7K~10K. resistor. Its states are: Low (0~0.8V) : Transmitter on (>0.8V,