HK-2917

CRYSTAL CLOCK OSCILLATORS Differential Positive ECL (DPECL) Data Sheet 0012G Rev. C SK-2910 Series Description The SK-2910 Series of quartz crystal oscillators provide DPECL Fast Edge compatible signals. This device is to operate using positive voltage and uses multiple ground pins for improved signal integrity. This device is intended to operate on positive voltage for PECL applications. Features • Wide frequency range–122.0MHz to 300.0MHz • User specified tolerance available • Case at electrical ground • Will withstand vapor phase temperatures of 253°C for 4 minutes maximum • All metal, resistance weld, hermetically sealed package • High shock resistance, to 1500g • Low Jitter • Overtone technology • High Q Crystal actively tuned oscillator circuit • Power supply decoupling internal • Dual ground plane for added stability • No internal PLL avoids cascading PLL problems • High frequencies due to proprietary design Electrical Connection Pin 1 2 6 7 8 9 13 14 Connection VCC VEE Case VEE Case Output /Output VEE Case VEE Case Enable/Disable 357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881 Email: nelsales@nelfc.com www.nelfc.com CRYSTAL CLOCK OSCILLATORS SK-2910 Series Continued Differential Positive ECL (DPECL) Operating Conditions and Output Characteristics Electrical Characteristics Parameter Frequency Duty Cycle Logic 0 (2) Logic 1(2) Rise & Fall Time Jitter, RMS(3) Enable Voltage(4) Disable Voltage Frequency Stability (1) Symbol Conditions Min --------122.0MHz ----@ 50% points 45/55% VOL ----VCC-1.95V VOH ----VCC-1.02V tr,tf 20-80%VO with 50 ohm load to VCC-2V -------------------with VEE=0V 0V ----with VEE=0V 3.0V dF/F Overall conditions including: -100ppm voltage, calibration, temp., 10 yr aging, shock, vibration Data Sheet 0012G Rev. C Typical ----------------350 psec ----------------- Max 300.0MHz 55/45% VCC-1.60V VCC-0.74V 600 psec 5 psec 1.0V VCC +100ppm General Characteristics Parameter Supply Voltage Supply Current Symbol VCC ICC Conditions ----50 ohm termination To 2.00V below VCC Low level Output Current ---------Min 4.75V 0.0 mA Typical 5.0V --------------------2 ms Max 5.25V 120 mA ±50.0 mA 70°C 125°C 300°C 10 ms Output current IO 0.0 mA 0°C Operating temperature TA Storage temperature TS -55°C Input: Logic High (ECL) - Disables VEE or Open - Enables Lead temperature TL Soldering, 10 sec. ----Load 50 Ohm to VCC-2V or Thevenin Equivalent, Bias Required --------Start-up time tS Environmental and Mechanical Characteristics Mechanical Shock Thermal Shock Vibration Soldering Condition Hermetic Seal Per MIL-STD-202, Method 213, Condition E Per MIL-STD-833, Method 1011, Condition A 0.060" double amplitude 10 Hz to 55 Hz, 35g’s 55Hz to 2000 Hz 300°C for 10 seconds Leak rate less than 1 x 10 -8 atm.cc/sec of helium Footnotes: 1) Standard frequency stability (±20,±25,±50ppm & others available) 2) VOL, VOH, referenced to ground 3) Jitter performance is frequency dependent. Please contact factory for full characterization. 4) Open to Enable pin also enables to output. Creating a Part Number SK - A291X - FREQ Package Code HK Leaded 8 pin (14pin) SK 8 pin (14 pin) SMD Gull Wing Input Voltage Code Specification A 3.3V 5V Tolerance/Performance 0 ±100ppm 0-70°C 1 ±50ppm 0-70°C 7 ±25ppm 0-70°C 9 Customer Specific A ±20ppm 0-70°C B ±50ppm -40 to +85°C C ±100ppm -40 to +85°C 357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881 Email: nelsales@nelfc.com www.nelfc.com