LEDGS75N

LED Highly-Diffused Lights (75 mm) Features • Designed to minimize surface textures and elevation changes, while providing uniform illumination over the field of view • 59 mm x 75 mm light aperture • The suggested field of view is 38 mm in diameter and the suggested stand off is 25 mm • Black anodized aluminum housing LED Highly-Diffused Light Models Models Illumination Type Color Cable Supply Voltage Supply Current Connections Pin 1 = +V fan Pin 2 = dc common fan Pin 3 = dc common Pin 4 = +V Power supply model PSA-12(E) or PS2V-12(E) is recommended (see other side) Pin 4 or 5 = +V Pin 1 or 6 = dc common Use strobe control module model SCM (see other side) LEDRS75N† Continuous highly-diffused light LEDGS75N† Red 640 nm Green 530 nm 0.5 m (18") terminated with 9-pin D-sub connector (male pins) 980 mA max. 12V dc ±10% with voltage regulation of ±1% 1.0 A max. LEDRS75N-S† Strobed highly-diffused light Red 640 nm 1.8 m (6') terminated with 9-pin D-sub connector (male pins) 24V dc ±10% with voltage regulation of ±1% 7.0 A max. 1 ms pulse † These models are not stocked and are non-returnable. Useful Life Environmental Rating Operating Conditions Green model: 50,000 hours; Red models: 60,000 hours. Note: actual useful life of strobed lights depends on duty cycle IEC IP20; NEMA 1 Temperature: 0° to 40°C (+32° to 104°F) Maximum relative humidity: 95% at 40°C (non-condensing) 82.6 mm 75 mm (3.25") (2.95") Light Aperture 25.4 mm (1.00") 25.4 mm (1.00") 25.8 mm (1.02") 25.4 mm (1.00") 77.0 mm (3.03) M6 x 1.0 6.4 (0.25") DEEP (4x) 12.7 mm (0.50") 75 mm (2.95") Light Aperture 138.4 mm (5.45") See Table 12.7 mm (0.50") WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. This warranty does not cover damage or liability for the improper application of Banner products. This warranty is in lieu of any other warranty either expressed or implied. Printed in USA 05/01 P/N 67442 LED Highly-Diffused Lights (75 mm) Accessories Continuous Power Supplies Models PSA-12 100-250V ac 50/60 Hz PSA-12E PSC-24† PSC-24E† Input Input Cord North America (NEMA 5-15) Cont. Europe (Schuko CEE 7) North America (NEMA 5-15) Cont. Europe (Schuko CEE 7) Output 12V dc ±5% with voltage regulation of ±1% 3.5 A max. 24V dc ±5% with voltage regulation of ±1% 2.2 A max. Output Cable 1.8 m (6') Terminated with 9-pin D-sub connector (female pins) 1.8 m (6') 2-wire Unterminated Used with Continuous types: LEDRS75N LEDGS75N 100-250V ac 50/60 Hz SCM Strobe Control Module (see below) Variable Power Supplies (see data sheet p/n 67449) Models PS2V-12† PS2V-12E† Input 100-140V ac 60 Hz 200-250V ac 50 Hz Input Cord North America (NEMA 5-15) Cont. Europe (Schuko CEE 7) Output 2-channels 6 - 12V dc 2 A max. per channel Output Cable 1.8 m (6') Terminated with 9-pin D-sub connector (female pins) Used with Continuous types: LEDRS75N LEDGS75N Strobe Control Module (see data sheet p/n 67448) Models SCM† Input 24V dc ±5% 2 A max. Trigger Input 5 - 12V dc pulse rising or falling (switch selectable) 10 mA max. Output 2-channels 24V dc ±5% 9 A nominal per channel @ 60 Hz Output Pulse Range Used with 5 to 1,300 microseconds Strobed types: LEDRS75N-S (Use Power Supply PSC-24 or PSC-24E) Extension Cables Models DB906 DB910 DB9Y† DB906S† DB910S DB9YS † † † † Length 1.8 m (6') Configuration Used with Continuous types: LEDRS75N LEDGS75N † Terminated both ends with 9-pin D-sub connector, for continuous lights 3.0 m (10') (one end male pins and opposite end female pins) 1.8 m (6') 1.8 m (6') Y cable for powering 2 lights from one supply, for continuous lights Terminated both ends with 9-pin D-sub connector, for strobed lights 3.0 m (10') (one end male pins and opposite end female pins) 1.8 m (6') Y cable for powering 2 lights from one supply, for strobed lights Strobed types: LEDRS75N-S These models are not stocked and are non-returnable. Banner Engineering Corp., 9714 Tenth Ave. No., Mpls., MN 55441 • Ph: 763.544.3164 • www.bannerengineering.com • Email: sensors@bannerengineering.com