046/47-MZ 2P 10A eng
2-03-2001
11:48
Pagina 46
Miniature Relays Series M Type MZ 2 poles 10A Monostable
• • • • • • • • • Miniature size PCB mounting Reinforced insulation 4 kV / 8 mm Switching capacity 10 A DC coils 1.87 to 160 VDC AC coils 4.8 to 264 VAC General purpose, industrial electronics Types: Standard, flux-free or sealed Switching AC/DC load
MZP
Product Description
H: Sealed with inert gas Sealing according to IP 67,suitaP: Standard,suitable for sol ble for automatic solde dering and manual washing. ring and/or partial immerF: Flux-free, suitable for autosion or spray washing. matic soldering and partial immersion or spray washing.
Ordering Key
Type Sealing Version (A = Standard) Contact code Coil reference number Contact rating
MZ P A 200 47 10
For General data, notes and special versions see page 48
Version A = 5.0 mm / Ag CdO (standard) C = 5.0 mm / hard gold plated D = 5.0 mm / flash gilded S = 5.0 mm / Ag Sn 02 Available only on request Ag Ni
Type Selection
Contact configuration 2 normally open contact 2 normally closed contact 2 change over contact (DPST -NO {2-form A}) (DPST -NC {2-form B}) DPDT {2-form C}) Contact rating 10 A 10 A 10 A Contact code 200 020 002
Coil Characteristics DC
Coil reference number
40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57
(20°C)
Winding resistance Ω
11 30 55 110 170 280 450 720 860 1150 1750 2700 4300 6450 9900 12550 16200 23500
Rated Voltage 200/002 020 VDC VDC
2.6 4.3 5.9 8.5 10.5 13.0 17.0 21.5 23.5 27.0 34.5 42.5 54.5 68.0 87.5 101.0 115.0 132.0 2.5 4.1 5.6 8.0 10.0 12.5 16.0 20.5 22.5 26.0 32.5 40.5 51.5 64.5 83.0 95.0 109.0 125.0
±%
10 10 10 10 10 10 10 15 15 15 15 15 15 15 15 15 15 15
Operating range Min. VDC Max.VDC 200/002 020
1.98 3.30 4.52 6.49 7.99 9.98 13.0 16.3 18.0 20.7 26.2 32.6 41.8 52.0 67.2 77.0 87.9 101.0 1.87 3.13 4.28 6.14 7.56 9.49 12.30 15.50 17.10 19.70 24.90 30.90 39.60 49.20 63.60 73.00 83.30 96.00 3.50 5.75 7.80 11.00 13.70 17.60 22.50 28.60 30.80 35.70 44.00 55;00 69.30 84.70 104.00 117.00 136.00 160.00
Must release VDC
≥ 5% of rated voltage
46
Specifications are subject to change without notice
046/47-MZ 2P 10A eng
2-03-2001
11:49
Pagina 47
Miniature Relays Series M Type MZ 2poles 10A Monostable
Coil Characteristics AC
Coil ref. no.
90 91 92 93 94 95 96 97
(20°C)
Inductance H
0.059 0.267 1.123 4.170 6.450 22.400 100.200 107.800
Must release Rated Current (mA) Rated Voltage Winding resistance Operating range VAC VAC 50Hz 60Hz Ω ±% min. VAC Max. VAC
6 12 24 48 60 110 220 240 12 56 230 870 1500 5300 20000 25000 10 10 10 15 15 15 15 15 4.8 9.6 19.2 38.4 48.0 88.0 176.0 192.0 6.6 13.2 26.4 52.8 66.0 129.0 242.0 264.0 270.0 119.0 57.0 30.5 23.8 12.3 5.9 5.7 237.0 104.0 50.0 26.7 21.0 10.8 5.2 5.0
≥ 15% of rated voltage
Contact Characteristics
Rating Material (standard version)2) Current (at 250VAC) Rated current Max. switching current Overload current (4sec ON / 40sec OFF cycle) Voltage Rated voltage Max.switching voltage (VDE 0435)
2) 3)
10 A AgCdO 10 A 12 A 14 A
Power Max. switching power with resistive load in AC 3) Max. switching power in DC Minimum switching current 2) (typical value) Life (see diagram 1) Typical electrical life at max. resistive load 1000 cycles/h 500 cycles/h Max.electrical repetition rate Mech. life at 18000 cycles/h
2500 VA see diagram 3 100mA at 24VDC
250 VAC 380 VAC
7.5 x 10 cycles 8 x 10 cycles 3600 cycles/h 50 x 10 cycles
4 6
4
See pag. 48
Dimensions
MZP...200/020/002 10A
h
Pin View
200 020 002
Wiring Diagrams
200 020 002
h’
MZP:
h = 25,2 mm h’= 4,3 - 5,3 mm
MZF/MZH: h = 26.5 mm h’= 2.8 - 3.8 mm
Diagrams
1 Expected life at 250 VAC (Resistive loads and repetition rate 1000 cycles/h) 2 Reduction of expected life against load power factor cos
ϕ
3 Max. switching power DC
I (Ampere) DC
Load power factor
V (Volt) DC
47
Specifications are subject to change without notice
Specifications are subject to change without notice
47
