OM1805N2M

OM1805N2M OM1812N2M OM1815N2M HERMETIC SURFACE MOUNT FIXED VOLTAGE POSITIVE REGULATORS APPROVED TO DESC DRAWINGS LCC 20 Fixed Voltage, Precision Positive Regulators In Hermetic Surface Mount Package FEATURES • • • • • • Hermetic Surface Mount Package Output Voltages: +5V, +12V, +15V Output Voltages Set Internally To ±1% Built-In Thermal Overload Protection Short Circuit Current Limiting Hi-Rel Screening Available DESCRIPTION These positive regulators are supplied in a hermetically sealed surface mount package. All protective features are designed into the circuit including thermal shutdown, current limiting and safe-area control. With heat sinking, they can deliver over .5 amps of output current. These units feature internally trimmed output voltages to ±1% of nominal voltage. Standard voltages are +5V, +12V, and +15V. These units are ideally suited for Military applications where a hermetic surface mount package is required. PART NUMBER DESIGNATOR Standard Military Drawing Number 5962-8778201 2X 5962-8777601 2X 5962-8855301 2X Omnirel Part Number OM1805N2M OM1812N2M OM1815N2M 3.5 4 11 R0 3.5 - 33 OM1805N2M - OM1815N2M ABSOLUTE MAXIMUM RATINGS @ 25°C Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +35 V Operating Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to + 150°C Storage Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to + 150°C Typical Power/Thermal Charateristics: Rated Power @ 25° C TC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 W TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1040 mW Thermal Resistance θJC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20°C/W θJA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120°C/W a ELECTRICAL CHARACTERISTICS 5 Volt Parameter Output Voltage Symbol VOUT VIN = 10V, Io = 100mA, -55°C ≤ TA ≤ 125°C (unless otherwise specified) Min. 4.92 Max. 5.08 5.15 Unit V V Test Conditions TA = 25°C VIN = 7.5V to 20V IO = 5mA to 500 mA, P < 2 W • 4.85 Line Regulation (Note 1) (Note 4) VRLINE VIN = 7.5V to 20V 5 mV mV mV mV mV mV mA mA mA • VIN = 8.0V to 12V 12 4 • Load Regulation (Note 1) Standby Current Drain ISCD ∆ISCD (Line) ∆ISCD (Load) VDO IO (pk) IDS ∆VIN ∆VOUT Output Noise Voltage (Note 3) Long Term Stability (Note 3) ∆VOUT ∆t TA = 25°C, t = 1000 hrs. NO TA = 25°C, ∆VOUT = 100mV, IO = 500mA TA = 25°C VIN = 35V 0.5 IO = 5mA to 500mA VIN = 7.5V to 20V VRLOAD IO = 5mA to 500 mA 10 25 • • • • 50 6 6.5 0.8 Standby Current Drain Change With Line Standby Current Drain Change With Load Dropout Voltage Peak Output Current Short Circuit Current (Note 2) Ripple Rejection 0.5 mA 2.5 1.7 0.7 V A A A dB dB • f =120 Hz, ∆VIN = 10V (Note 3) TA = 25°C, f =10 Hz to 100KHz 68 2.0 • 60 40 µV/V RMS 75 mV 3.5 Notes: 1. Load and Line Regulation are specified at a constant junction temperature. Pulse testing with low duty cycle is used. Changes in output voltage due to heating effects must be taken into account separately. 2. Short Circuit protection is only assured up to VIN = 35V. 3. If not tested, shall be guaranteed to the specified limits. The • denotes the specifications which apply over the full operating temperature range. 4. Minimum load current for full line regulation = 5.0 mA. 3.5 - 34 OM1805N2M - OM1815N2M ELECTRICAL CHARACTERISTICS 12 Volt Parameter Output Voltage Symbol VOUT VIN = 19V, Io = 100mA, -55°C ≤ TA ≤ 125°C (unless otherwise specified) Min. 11.88 Max. 12.12 12.36 Unit V V Test Conditions TA = 25°C VIN = 14.5V to 27V IO = 5mA to 500 mA, P < 2W Line Regulation (Note 1) (Note 4) VIN = 16V to 22V VRLINE VIN = 14.5V to 27V 18 mV mV mV mV mV mV mA mA mA • 11.64 • • 50 9 30 30 Load Regulation (Note 1) Standby Current Drain VRLOAD ISCD ∆ISCD (Line) ∆ISCD (Load) VDO IO (pk) IDS ∆VIN ∆VOUT NO ∆VOUT ∆t IO = 5mA to 500mA • • • • • 0.5 60 6.0 6.5 0.8 Standby Current Drain Change With Line Standby Current Drain Change With Load Dropout Voltage Peak Output Current Short Circuit Current (Note 2) Ripple Rejection VIN = 15V to 30V IO = 5mA to 500mA ∆VOUT = 100mV, IO = 500mA TA = 25°C VIN = 35V 0.5 mA 2.5 1.7 0.7 V A A A dB dB • f =120 Hz, ∆VIN = 10V (Note 3) TA = 25°C, f =10 Hz to 100KHz TA = 25°C, t = 1000 hrs. 61 2.0 • 54 40 Output Noise Voltage (Note 3) Long Term Stability (Note 3) µV/V RMS 120 mV Notes: 1. Load and Line Regulation are specified at a constant junction temperature. Pulse testing with low duty cycle is used. Changes in output voltage due to heating effects must be taken into account separately. 2. Short Circuit protection is only assured up to VIN = 35V. 3. If not tested, shall be guaranteed to the specified limits. The • denotes the specifications which apply over the full operating temperature range. 4. Minimum load current for full line regulation = 5.0 mA. MECHANICAL OUTLINE Terminal Number .065 .020 X45° REF. (±.003) .009 R. 20 PLCS. .040 4 .010 .075 (±.010) TYP. 9 .025 TYP. .085 3 1 19 .160 SQ. REF. 13 18 14 .003 .025 SQ. TYP. .050 (±.005) TYP. .050 TYP. .040 X45° REF (3 PL) NOTE: For normal operation, VOUT must be connected externally to load. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 NC VIN NC NC NC NC GND NC NC VOUT NC VOUT NC NC VOUT SENSE NC VIN NC NC NC 3.5 3.5 - 35 OM1805N2M - OM1815N2M ELECTRICAL CHARACTERISTICS 15 Volt Parameter Output Voltage Symbol VOUT VIN = 23V, Io = 100mA, -55°C ≤ TA ≤ 125°C (unless otherwise specified) Min. 14.8 Max. 15.2 15.4 Unit V V Test Conditions TA = 25°C VIN = 18.5V to 30V IO = 5mA to 500 mA, P < 2W • 14.6 Line Regulation (Note 1) (Note 4) VRLINE VIN = 17.5V to 30V 20 mV mV mV mV mV mV mA mA mA • VIN = 20V to 26V 50 15 • Load Regulation (Note 1) Standby Current Drain ISCD ∆ISCD (Line) ∆ISCD (Load) VDO IO (pk) IDS ∆VIN ∆VOUT Output Noise Voltage (Note 3) Long Term Stability (Note 3) ∆VOUT ∆t TA = 25°C, t = 1000 hrs. NO TA = 25°C, ∆VOUT = 100mV, IO = 500mA TA = 25°C VIN = 35V 0.5 IO = 5mA to 500mA VIN = 18.5V to 30V VRLOAD IO = 5mA to 500 mA 25 50 • • • • 90 6.0 6.5 0.8 Standby Current Drain Change With Line Standby Current Drain Change With Load Dropout Voltage Peak Output Current Short Circuit Current (Note 2) Ripple Rejection 0.5 mA 2.5 1.7 0.7 V A A A dB dB • f =120 Hz, ∆VIN = 10V (Note 3) TA = 25°C, f =10 Hz to 100KHz 54 2.0 • 52 40 µV/V RMS 150 mV Notes: 1. Load and Line Regulation are specified at a constant junction temperature. Pulse testing with low duty cycle is used. Changes in output voltage due to heating effects must be taken into account separately. 2. Short Circuit protection is only assured up to VIN = 35V. 3. If not tested, shall be guaranteed to the specified limits. The • denotes the specifications which apply over the full operating temperature range. 4. Minimum load current for full line regulation = 5.0 mA. 3.5