PJ31002

PJ31002

  • 厂商:

    ETC1

  • 封装:

  • 描述:

    PJ31002 - Tone Ringer For Telephone Set - List of Unclassifed Manufacturers

  • 详情介绍
  • 数据手册
  • 价格&库存
PJ31002 数据手册
PJ31002 Tone Ringer For Telephone Set T • • • • • h e PJ31002 is a bipolar integrated circuit designed for telephone bell replacement. D IP -8 SOP -8 FEATURES Oscillation frequency is variable Few external components Sustaining power is low P ackage is compact ( DIP-8) Current consumption is small P in: 1. Vcc 2. Rsl 3. Lfi 4. Lfo 5. Gnd 6. Hfo 7. Hfi 8. Out ORDERING INFORMATION Device P J31002CD P J31002CS Operating Temperature -20℃~+85℃ Package DIP-8 S OP-8 ELECTRICAL CHARACTERISTICS ( Unless otherwise specified, T a=25 ℃, Vcc=24V) Parameter Operating Voltage S upply Initiation Voltage S ustaining Voltage S upply Initiation Current S ustaining Current Oscillator Frequence (NOTE3) Oscillator Frequence (NOTE3) Oscillator Frequence (NOTE3) Output Voltage *Hi* Output Voltage *Lo* R inging Start Voltage Symbol Vopr Vsi Vsus Isi lsus fL fH1 fH2 Voh Vol Vtr Min. -15 10.5 1.4 0.35 9 461 576 19.7 0.5 -Typ. -17 12.0 3.3 0.9 10 512 640 22.0 0.9 -Max. 38 19.5 13.0 4.2 1.5 11 563 703 23.5 1.4 36.0 Unit V V V mA mA Hz Hz Hz V V V loh=10mA 7 Pin=GND Iol=10mA 7 Pin=5.5V (NOTE 4) (NOTE 1) (NOTE 2) Vcc=Vsi, No LOAD Vcc=Vsus, No LOAD Conditions Test Circuit FIG.4 FIG.4 FIG.4 FIG.4 FIG.4 FIG.5 FIG.5 FIG.5 FIG.4 FIG.4 FIG.3 ABSOLUTE MAXIMUM RATING ( T a=25 ℃ ) Parame te r Supply Voltage P ower Dissipation Operating T emperature Range Storage T emperature Range Symbol Vcc Pd T opr T stg 1-5 Rating 38 500 -20 ~ +85 -55 ~ +125 Unit V mW ℃ ℃ 2002/01.rev.A PJ31002 Tone Ringer For Telephone Set ( NOT E 1 ) Supply initiation voltage is the value of DC supply voltage required to start the tone ringer oscillation. Sustaining voltage is the value of DC supply voltage required to maintain oscillation. Oscillator frequency is determined by the following equations : fL = 1 / ( 1.234 * R1 * C1 ) fH1 = 1 / ( 1.515 * R2 * C2 ) fH2 = 1.24 * fH1 ( NOT E 4 ) Hz Hz Hz ( NOT E 2 ) ( NOT E 3 ) Ringing start voltage is the value of AC supply voltage required to start the tone ringer ringing in FIG.3 T his product is not designed for protection against radioactive rays. All data and specifications are subject to change without notice. ( NOT E 5 ) ( NOT E 6 ) Figure 2. Block Diagram 2-5 2002/01.rev.A PJ31002 Tone Ringer For Telephone Set H O W TO USE THE RSL PIN In the IC, the supply initiation current (lsi) can be Vc c 1 changed using the RSL Pin . As show is the diagram, the RSL (Pin 2) is grounded through resistor Rs. By changing the Rs value, supply initiation current can be changed. Supply voltage (Vcc) vs. supply current (lcc) Rs 5 2 characteristics resulting from changes in the value of Rs are shown in the following diagram. G ND Ic c (m A) 4 Rs= 6.8K Rs= 10K Rs= 18K 3 2 1 10 20 Vc c (V) Figure 3.Ringing Start Voltage Te st Circuit 1N4004* 4 Tone Ringer 10uF/35 1 2 27V 1uF/250 680K 103 pF A C f=20H 104p F 8 7 6 5 100 4.7uF/50 8.2K + + 10K 3 4 3-5 2002/01.rev.A PJ31002 Tone Ringer For Telephone Set FIG. 4 Test Circuit (1) Isi Isus Tone Ringer IC 1 2 Vsi Vsus V Vcc 3 Rs 4 R1 C1 C2 Voh Vol 5 8 7 6 R2 5 5V V SW2 3 2 1 SW1 1 To Oscilloscope 2 10mA A • S WITCH POSITION IS THE FOLLOWING TABLE : PARAMETER SW1 SW2 Vsi , Isi Vsus , Isus Voh Vol 1 1 2 2 1 1 2 3 R1 R2 C1 C2 = 165 K (+/-) = 191 K (+/-) = 0.47 µF (+/-) = 0.0068 µF (+/-) 1% 1% 5% 5% FIG. 4 Te st Circuit (2) Isi.Isus To ne R in ge r IC 1 3 2 1 2 SW 1 3 4 5.5V C1 1 SW2 R1 8 7 6 5 C2 2 R2 f1 .fH1. fH2 To Oscillosco pe A Vsi. Vsus V Vcc Rs • S WITCH POSITION IS THE FOLLOWING TABLE : PARAMETER SW1 SW2 FL fH1 fH2 1 1 2 1 1 2 R1 R2 C1 C2 = 165 K (+/-) 1% = 191 K (+/-) 1% = 0.47 µF (+/-) 5% = 0.0068 µF ( +/- ) 5 % 4-5 2002/01.rev.A PJ31002 Tone Ringer For Telephone Set DIM A B C D G J K L M MILLIMETERS MIN MAX 9.07 9.32 6.22 6.48 3.18 4.43 0.35 0.55 2.54BSC 0.29 0.31 3.25 3.35 7.75 8.00 10° INCHES MIN MAX 0.357 0.367 0.245 0.255 0.125 0.135 0.019 0.020 0.10BSC 0.011 0.012 0.128 0.132 0.305 0.315 10° DIM A B C D F G K M P R MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27BSC 0.10 0.25 0° 7° 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.189 0.196 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.05BSC 0.004 0.009 0° 7° 0.229 0.244 0.010 0.019 5-5 2002/01.rev.A
PJ31002
物料型号: - PJ31002CD:工作温度范围为-20°C至+85°C,封装为DIP-8。 - PJ31002CS:封装为SOP-8。

器件简介: - PJ31002是一款为电话振铃设计的音频振铃发生器,旨在替代电话电铃。 - 特点包括可变振荡频率、外部组件少、低维持功率、紧凑的封装(DIP-8)和低电流消耗。

引脚分配: - 1. Vcc(电源) - 2. Rsl(电阻控制引脚) - 3. Lf(低频引脚) - 4. Lfo(低频输出) - 5. Gnd(地) - 6. Hfo(高频输出) - 7. Hi(高频输入) - 8. Out(输出)

参数特性: - 工作电压(Vopr):38V - 供电启动电压(Vsi):15V至19.5V - 维持电压(Vsus):10.5V至13.0V - 供电启动电流(Isi):1.4mA至4.2mA - 维持电流(Isus):0.35mA至1.5mA - 振荡频率(fL、fH1、fH2):分别为9Hz至11Hz、461Hz至563Hz、576Hz至703Hz - 输出电压(Voh、Vol):分别为19.7V至23.5V、0.5V至1.4V - 振铃启动电压(Vtr):36.0V

功能详解: - 该器件通过改变RSL引脚的电阻值(Rs)来改变供电启动电流(Isi)。 - 振荡频率由外部电阻和电容值决定,具体公式为:fL=1/(1.234R1C1) Hz,fH1=1/(1.515R2C2) Hz,fH2=1.24fH1 Hz。

应用信息: - 该器件适用于电话振铃应用,可以产生音频振铃信号。

封装信息: - 提供了DIP-8和SOP-8两种封装的详细尺寸信息,包括最小值、最大值、英寸和毫米单位。
PJ31002 价格&库存

很抱歉,暂时无法提供与“PJ31002”相匹配的价格&库存,您可以联系我们找货

免费人工找货