RC0402FR105R6L

RC0402 (Pb Free) 5%, 1% GENERAL PURPOSE CHIP RESISTORS DATA SHEET Product specification – Sep 03, 2004 V.2 Supersedes Date of Mar. 06, 2003 Product specification 2 10 Chip Resistor Surface Mount RC SERIES 0402 (Pb Free) SCOPE This specification describes RC0402 series chip resistors with lead-free terminations made by thick film process. ORDERING INFORMATION P art number is identified by the series, size, tolerance, packing type, temperature coefficient, taping reel and resistance value. YAGEO ORDERING CODE C TC C ODE ORDERING EXAMPLE (4) (5) (6) RC0402 X X X XX XXXX L (1) (2) (3) (1) TOLERANCE F = ±1% J = ±5% T he ordering code of a RC0402 chip resistor, value 56 X w ith ±1% tolerance, supplied in 7-inch tape reel is: RC0402FR-0756RL. NOTE (2) PACKAGING TYPE R = Paper/PE taping reel 1. The “L” at the end of the code is only for ordering. On the reel label, the standard CTC will be mentioned an additional stamp “LFP”= lead free production. 2. Products with lead in terminations fulfil the same requirements as mentioned in this datasheet. 3. Products with lead in terminations will be phased out in the coming months (before July 1st, 2006) (3) TEMPERATURE COEFFICIENT OF RESISTANCE – = Base on spec (4) TAPING REEL 07 = 7 inch dia. Reel 10 = 10 inch dia. Reel (not preferred) 13 = 13 inch dia. Reel (5) RESISTANCE VALUE 5R6, 56R, 560R, 56K, 10M. (6) RESISTOR TERMINATIONS L = Lead free terminations (pure Tin) w ww.yageo.com Sep 03, 2004 V.2 Product specification 3 10 Chip Resistor Surface Mount RC SERIES 0402 (Pb Free) MARKING RC0402 N o marking ynsc007 Fig. 1 CONSTRUCTION The resistors are constructed out of a high-grade ceramic body. Internal metal electrodes are added at each end and connected by a resistive paste. The composition of the paste is adjusted to give the approximate required resistance and laser cutting of this resistive layer that achieves tolerance trims the value. The resistive layer is covered with a protective coat. protective coat handbook, 4 columns resistor layer inner electrode H end termination I2 ceramic substrate MBE940_a Fig. 2 Chip resistor construction Finally, the two external terminations (pure Tin) are added. See fig. 2. DIMENSIONS Table 1 TYPE L (mm) W (mm) H (mm) I1 (mm) I2 (mm) RC0402 1.00 ±0.05 0.50 ±0.05 0.35 ±0.05 0.20 ±0.10 0.25 ±0.10 L MBE940_a protective coat I1 W Fig. 3 Chip resistor dimension For dimension see Table 1 w ww.yageo.com Sep 03, 2004 V.2 Product specification 4 10 Chip Resistor Surface Mount RC SERIES 0402 (Pb Free) ELECTRICAL CHARACTERISTICS Table 2 CHARACTERISTICS Operating Temperature Range Maximum Working Voltage Maximum Overload Voltage Dielectric Withstanding Voltage Resistance Range RC0402 1/16 W –55 °C to +155 °C 50 V 100 V 100 V 5% (E24) 1 Ω to 10 MΩ 1% (E96) 1 Ω to 10 MΩ Zero Ohm Jumper < 0.05 Ω 10 Ω < R ≤ 10 MΩ 1 Ω < R ≤ 10 Ω Rated Current Maximum Current ±100 ppm/°C ±200 ppm/°C 1.0 A 2.0 A FOOTPRINT AND SOLDERING PROFILES F or recommended footprint and soldering profiles, please see the special data sheet “Chip resistors mounting”. ENVIRONMENTAL DATA F or material declaration information (IMDS-data) of the products, please see the separated info “Environmental data”. Temperature Coefficient Jumper Criteria PACKING STYLE AND PACKAGING QUANTITY Table 3 Packing style and packaging quantity PRODUCT TYPE RC0402 PACKING STYLE Paper / PE Taping Reel (R) REEL DIMENSION 7" (178 mm) 10" (254 mm) / not preferred 13" (330 mm) QUANTITY PER REEL 10,000 units 20,000 units 50,000 units NOTE 1. For Paper/PE tape and reel specification/dimensions, please see the special data sheet “Packing” document. w ww.yageo.com Sep 03, 2004 V.2 Product specification 5 10 Chip Resistor Surface Mount RC SERIES 0402 (Pb Free) FUNCTIONAL DESCRIPTION POWER RATING R C0402 rated power at 70°C is 1/16 W RATED VOLTAGE T he DC or AC (rms) continuous working voltage corresponding to the rated power is determined by the following formula: V= √ (P X R) Where V=Continuous rated DC or AC (rms) working voltage (V) P=Rated power (W) R=Resistance value ( X ) PULSE LOADING CAPABILITIES Pmax (%Prated) 100 MRA632 50 0 −55 0 50 70 155 100 Tamb (°C) Fig. 4 Maximum dissipation (Pmax) in percentage of rated power as a function of the operating ambient temperature (Tamb ) 103 ^ CCB508 Vmax (V) 1.2/50 µs 102 10/700 µs 10 1 1 10 102 103 104 105 Rn (Ω) 106 Fig. 5 Maximum permissible peak pulse voltage without failing to open circuit’ in accordance with DIN IEC 60040 (CO) 533 for type: RC0402 w ww.yageo.com Sep 03, 2004 V.2 Product specification 6 10 Chip Resistor Surface Mount RC SERIES 0402 (Pb Free) 103 Pmax (V) 102 ^ CCB509 10 single pulse 1 10−1 10−6 10−5 10−4 10−3 10−2 10−1 ti (s) 1 Fig. 6 Pulse on a regular basis for type: RC0402; maximum permissible peak pulse power as a function of pulse duration for single pulse and repetitive pulse tp/ti = 1000 200 Vmax (V) 150 ^ CCB507 100 50 0 10−6 10−5 10−4 10−3 10−2 10−1 ti (s) 1 Fig. 7 Pulse on a regular basis for type: RC0402; maximum permissible peak pulse voltage as a function of pulse duration w ww.yageo.com Sep 03, 2004 V.2 Product specification 7 10 Chip Resistor Surface Mount RC SERIES 0402 (Pb Free) TESTS AND REQUIREMENTS Table 4 Test condition, procedure and requirements TEST Temperature Coefficient of Resistance (T.C.R.) TEST METHOD MIL-STD-202F-method 304; JIS C 5202-4.8 PROCEDURE At +25/–55 °C and +25/+125 °C REQUIREMENTS Refer to table 2 Formula: R2–R1 T.C.R= ------------------------- ×106 (ppm/°C) R1(t2–t1) Where t1=+25 °C or specified room temperature t2=–55 °C or +125 °C test temperature R1=resistance at reference temperature in ohms R2=resistance at test temperature in ohms Thermal Shock MIL-STD-202F-method 107G; IEC 60115-1 4.19 At –65 (+0/–10) °C for 2 minutes and at +155 (+10/–0) °C for 2 minutes; 25 cycles At –65 (+0/–5) °C for 1 hour; RCWV applied for 45 (+5/–0) minutes ±(0.5%+0.05 Ω) for 1% tol. ±(1.0%+0.05 Ω) for 5% tol. ±(0.5%+0.05 Ω) for 1% tol . ±(1.0%+0.05 Ω) for 5% tol. No visible damage Low Temperature Operation MIL-R-55342D-Para 4.7.4 Short Time Overload MIL-R-55342D-Para 4.7.5; IEC 60115-1 4.13 2.5 × RCWV applied for 5 seconds at room temperature ±(1.0%+0.05 Ω) for 1% tol. ±(2.0%+0.05 Ω) for 5% tol. No visible damage Insulation Resistance MIL-STD-202F-method 302; IEC 60115-1 4.6.1.1 RCOV for 1 minute ≥10 GΩ Type Voltage (DC) RC0402 100 V Dielectric Withstand Voltage MIL-STD-202F-method 301; IEC 60115-1 4.6.1.1 Maximum voltage (Vrms) applied for 1 minute No breakdown or flashover Type Voltage (AC) RC0402 100 Vrms ±(0.5%+0.05 Ω) for 1% tol. ±(1.0%+0.05 Ω) for 5% tol. No visible damage Resistance to Soldering Heat MIL-STD-202F-method 210C; IEC 60115-1 4.18 Unmounted chips; 260 ±5 °C for 10 ±1 seconds Life MIL-STD-202F-method 108A; IEC 60115-1 4.25.1 At 70±2 °C for 1,000 hours; RCWV applied for 1.5 hours on and 0.5 hour off ±(1%+0.05 Ω) for 1% tol. ±(3%+0.05 Ω) for 5% tol. w ww.yageo.com Sep 03, 2004 V.2 Product specification 8 10 Chip Resistor Surface Mount RC SERIES 0402 (Pb Free) TEST Solderability TEST METHOD MIL-STD-202F-method 208A; IEC 60115-1 4.17 PROCEDURE Solder bath at 245±3 °C Dipping time: 2±0.5 seconds REQUIREMENTS Well tinned (≥95% covered) No visible damage ±(1.0%+0.05 Ω) for 1% tol. ±(1.0%+0.05 Ω) for 5% tol. No visible damage No smeared Bending Strength JIS C 5202.6.14; IEC 60115-1 4.15 Resistors mounted on a 90 mm glass epoxy resin PCB (FR4) Bending: 5 mm Resistance to Solvent Noise MIL-STD-202F-method 215; IEC 60115-1 4.29 JIS C 5202 5.9; IEC 60115-1 4.12 lsopropylalcohol (C3H7OH) or dichloromethane (CH2Cl2) followed by brushing Maximum voltage (Vrms) applied. Resistors range R < 100 Ω 100 Ω ≤ R < 1 KΩ 1 KΩ ≤ R < 10 KΩ 10 KΩ ≤ R < 100 KΩ 100 KΩ ≤ R < 1 MΩ 1 MΩ ≤ R ≤ 22 MΩ Value 10 dB 20 dB 30 dB 40 dB 46 dB 48 dB Humidity (steady state) JIS C 5202 7.5; IEC 60115-8 4.24.8 1,000 hours; 40±2 °C; 93(+2/–3)% RH RCWV applied for 1.5 hours on and 0.5 hour off ±(0.5%+0.05 Ω) for 1% tol. ±(2.0%+0.05 Ω) for 5% tol. No visible damage Leaching EIA/IS 4.13B; IEC 60115-8 4.18 Solder bath at 260±5 °C Dipping time: 30±1 seconds At room temperature; 2.5 × RCWV applied for 1 second on and 25 seconds off; total 10,000 cycles On request Intermittent Overload JIS C 5202 5.8 ±(1.0%+0.05 Ω) for 1% tol. ±(2.0%+0.05 Ω) for 5% tol. Resistance to Vibration Moisture Resistance Heat On request MIL-STD-202F-method 106F; IEC 60115-1 4.24.2 42 cycles; total 1,000 hours Shown as Fig. 8 ±(0.5%+0.05Ω) for 1% tol. ±(2.0%+0.05Ω) for 5% tol. No visible damage w ww.yageo.com Sep 03, 2004 V.2 Product specification 9 10 Chip Resistor Surface Mount RC SERIES 0402 (Pb Free) 75 temperature [°C] 50 initial drying 24 hours 90 − 98% RH 80 − 98% RH 90 − 98% RH 80 − 98% RH 90 − 98% RH rate of change of temperature is unspecified, however, specimens shall not be subjected to radiant heating from chamber conditioning processes +10 °C (+18 °F) −2 °C (−3.6 °F) initial measurements as specified in 2.2 circulation of conditioning air shall be at a minimum cubic rate per minute equivalent to 10 times the volume of the chamber end of final cycle; measurements as specified in 2.7 25 0 temperature tolerance ±2 °C (±3.6 °F) unless otherwise specified STEP1 prior to first cycle only HBK073 optional sub-cycle if specified (2.3); sub-cycle performed during any 5 of the first 9 cycles; humidity uncontrolled during sub-cycle voltage applied as specified in 2.4 STEP2 STEP3 STEP4 STEP5 STEP6 STEP7 one cycle 24 hours; repeat as specified in 2.5 0 5 10 15 20 time [h] 25 Fig. 8 Moisture resistance test requirements w ww.yageo.com Sep 03, 2004 V.2 Product specification 10 10 Chip Resistor Surface Mount RC SERIES 0402 (Pb Free) REVISION HISTORY REVISION Version 2 DATE Sep 03, 2004 CHANGE NOTIFICATION - DESCRIPTION - Test method and procedure updated - PE tape added (paper tape will be replaced by PE tape) w ww.yageo.com Sep 03, 2004 V.2