SC614-RL1

SC-614 Speech And Music Processor Data sheet Features Advanced, integrated speech synthesizer for high-quality sound. Operates up to 12.32 MHz (performs up to 12 MIPS). Single-chip solution for up to 6.8 minutes of speech. External ROM interface for up to 18.8 hours of speech. Supports high-quality synthesis algorithms such as MX, CX, Simple CX, LX, ADPCM, and polyphonic music. Simultaneous speech plus music capability. Very low-power operation, ideal for hand-held devices. Low-voltage operation, sustainable by three batteries. Reduced power stand-by modes, less than 10 µA in deep-sleep mode. Contains 64k byte words onboard ROM (2k words reserved). 640-word RAM. 64 I/O pins consisting of 40 general-purpose bit configurable I/O. 8 inputs with programmable pullup resistor and dedicated interrupt (key-scan). 16 dedicated output pins. Direct speaker driver, 32Ω (PDM). One-bit comparator with edge-detection interrupt service. Resistor-trimmed oscillator or 32.768 khz crystal reference oscillator. Serial scan port for in-circuit emulation and diagnostics. The SC-614 is sold in die form, or 100-pin LQFP package. An emulator device is available in a ceramic package for development (SC-614-P). Description The SC-614 is a low-cost, mixed-signal processor that combines a speech synthesizer, general-purpose I/O, onboard ROM, and direct speaker-drive in a single package. The computational unit utilizes a powerful new DSP which gives the SC-614 unprecedented speed and computational flexibility compared with previous devices of its type. The SC-614 supports a variety of speech and audio coding algorithms, providing a range of options with respect to speech duration and sound quality. 16-Bit Microprocessor SC-614 Block Diagram 10-Bit DAC 640-words RAM TIMER 1 TIMER 2 PLLM 64 KBytes ROM COMPARATOR 64 I/O The device consists of a micro-DSP core, embedded program, and data memory, and a self-contained clock generation system. General-purpose periphery is comprised of 64 bits of partially configurable I/O. The core processor is a general-purpose 16-bit microcontroller with DSP capability. The basic core block includes computational unit (CU), data address unit, program address unit, two timers, eight level interrupt processor, and several system and control registers. The core processor gives the SC-614 break-point capability in emulation. The processor is Harvard type for efficient DSP algorithm execution. It requires separate program and data memory blocks to permit simultaneous access. It is configured in 32K 17-bit words. The total ROM space is divided into two areas: 1. The lower 2K words are reserved by Sensory for the purposes of a built-in self-test 2. The upper 30K is for user program/data © 2003 Sensory Inc. P/N 80-0210-C 1 SC-614 Data sheet The data memory is internal static RAM. The RAM is configured in 640 17-bit words. Both memories are designed to consume minimum power at a given system clock and algorithm acquisition frequency. A flexible clock generation system enables the software to control the clock over a wide frequency range. The implementation uses a phase-locked loop (PLL) circuit that drives the processor clock at a selectable frequency between the minimum and maximum achievable. Selectable frequencies for the processor clock are spaced apart in 65.536 kHz steps. The PLL clock-reference is also selectable; either a resistor-trimmed oscillator or a crystal-referenced oscillator may be used. Internal and external clock sources are controlled separately to provide different levels of power management. The periphery consists of five 8-bit wide general-purpose I/O ports, one 8-bit wide dedicated input port, and one 16-bit wide dedicated output port. The bidirectional I/O can be configured under software control as either highimpedance inputs or as totem-pole outputs. They are controlled via addressable I/O registers. The input-only port has a programmable pullup option (70k minimum resistance) and a dedicated service interrupt. These features make the input port especially useful as a key-scan interface. A simple one-bit comparator is also included in the periphery. The comparator is enabled by a control register, and its pin access is shared with two pins in one of the general-purpose I/O ports. Rounding out the SC-614 periphery is a built-in pulse-density-modulated DAC (digital-to-analog converter) with direct speaker-drive capability. The functional block diagram gives an overview of the SC-614 functionality. Functional Block Diagram 2 P/N 80-0210-C © 2003 Sensory Inc. Data Sheet SC-614 Pin Assignment PD7 VDD2 VSS2 PC0 PD0 PD1 PD2 PD3 PD4 PD5 PD6 PC1 PC2 PC3 PC4 PC5 PC6 PC7 PB0 76 75 74 73 72 71 70 69 68 67 66 65 NC NC NC NC 80 79 NC NC 78 77 99 98 97 96 95 94 93 92 91 90 89 VSS3/DA 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 100 82 81 88 87 86 85 84 83 PB1 PB2 PB3 PB4 PB5 PB6 PB7 VDD1 VSS1 PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 PLL OSCIN OSCOUT NC NC NC VSS PE0 19 1 NC NC NC 20 85 DACM VDD3/DA DACP VDD PF7 PF6 PF5 PF4 PF3 PF2 PF1 PF0 NC PG15 PG14 PG13 PG12 PG11 PG10 PG9 S C -614 (top view of the die) SC-614 (100-lead LQFP) 64 63 62 61 60 59 58 57 56 55 54 53 52 51 41 65 42 64 PG8 SCANOUT TEST VDD4 NC NC PG7 SYNC SCANCLK PG6 PG5 PG4 PG3 PG2 PG1 PG0 PE5 PE4 PE3 PE2 SCANIN RESET_ NAME PA0 – PA7 PB0 – PB7 PC0 – PC7 PD0 – PD7 PE0 – PE7 PF0 – PF7 PG0 – PG7 PG8 – PG15 PIN NO. 66 → 59 76 → 69 90 → 83 100 → 93 51 → 44 16 → 9 37 → 30 25 → 18 PAD NO. 75 → 68 85 → 78 8→1 18 → 11 63 → 56 31 → 24 49 → 42 39 → 32 VSS4 I/O I/O I/O I/O I/O I/O I DESCRIPTION Port A general-purpose I/O (1 Byte) Port B general-purpose I/O (1 Byte) Port C general-purpose I/O (1 Byte) Port D general-purpose I/O (1 Byte) Port E general-purpose I/O (1 Byte) Port F key-scan input (1 Byte) O Port G dedicated output (2 Bytes) Pins PD4 and PD5 may be dedicated to the comparator function, if the comparator enable bit is set. Scan Port Control Signals SCANIN 42 SCANOUT 38 SCANCLK 41 SYNC 40 TEST 39 54 50 53 52 51 I O I I I Scan port data input Scan port data output Scan port clock Scan port synchronization SC-614: test modes The scan port pins must be bonded out on any SC-614 production board. Reference Oscillator Signals OSCOUT 56 65 OSCIN 57 66 PLL 58 67 Digital-to-Analog Sound Output DACP 7 22 DACM 5 20 Initialization RESET_ 43 55 Power Signals † † VSS 1 , 26, 52, 67, 91 9, 19 , 40, 64, 76 † † VDD 6 , 8, 27, 68, 92 10, 21 , 23, 41, 77 O Resistor/crystal reference out I Resistor/crystal reference in O Phase-lock-loop filter O Digital-to-analog plus output (+) O Digital-to-analog minus output (–) I Initialization Ground Processor power (+) † The VSS and VDD connections service the DAC circuitry. Their pins tend to sustain a higher current draw. A dedicated decoupling capacitor across these pins is therefore required. © 2003 Sensory Inc. PE7 PE6 PE1 P/N 80-0210-C 3 SC-614 Data sheet Absolute Maximum Ratings Absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VDD (see Note 1) Supply current, IDD (see Note 2) Input voltage range, VI (see Note 1) Output voltage range, VO (see Note 1) Storage temperature range, TA –0.3 to 7 V 35 mA –0.3 to VDD + 0.3 V –0.3 to VDD + 0.3 V –30°C to 125°C WARNING: Stressing the SC-614 beyond the “Absolute Maximum Ratings” may cause permanent damage. These are stress ratings only. Operation beyond the “Operating Conditions” is not recommended and extended exposure beyond the “Operating Conditions” may affect device reliability. NOTES: 1. Unless otherwise noted, all voltages are measured with respect to VSS. 2. The total supply current includes the current out of all the I/O pins as well as the operating current of the device. Recommended Operating Conditions Supply voltage (with respect to VSS), VDD CPU clock rate (as programmed), f(CPU) Load resistance between DACP and DACM, R(DAC) Operating free-air temperature, TA MIN 3 64 32 0 MAX 5.2 12,320 70 UNIT V kHz Ω °C Device functionality Timing Requirements t(RESET) t1(WIDTH) t2(WIDTH) Reset low pulse width, while VDD is within specified limits Pulse width required prior to a negative transition at pin PD3, PD5, or PF0 → PF7‡ Pulse width required prior to a positive transition at pin PD2 or PD4† MIN 100 2 2 MAX UNIT ns 1/FCPU 1/FCPU ‡ While these pins are being used as interrupt inputs. t(RESET) t(RESET) Figure 1: Initialization Timing Diagram t1(WIDTH (PD3, PD5, or F port)) t2(WIDTH (PD2, or PD4)) t1(WIDTH) t2(WIDTH) Figure 2: External Interrupt Pin Pulse Width Requirements t1WIDTH and t2WIDTH 4 P/N 80-0210-C © 2003 Sensory Inc. Data Sheet SC-614 DC Electrical Characteristics, TA = 0 to 70°C PARAMETER TEST CONDITIONS MIN Positive going threshold VDD = 3 V Negative going threshold Hysteresis Threshold changes Positive going threshold VDD = 5.2 V Negative going threshold Hysteresis VDD = 3 V 2 High-level input voltage VDD = 4.5 V 3 VDD = 5.2 V 3.5 VDD = 3 V 0 Low-level input voltage VDD = 4.5 V 0 VDD = 5.2 V 0 High-level output current per pin of I/O port VOH = 4 V Low-level output current per pin of I/O port VOL = 0.5 V VDD = 4.5 V High-level output DAC current VOH = 4 V Low-level output DAC current VOL = 0.5 V Input leakage current Excludes OSCIN Standby current RESET is low Operating current VDD = 4.5 V, FCLOCK = 12.32 MHz VDD = 4.5 V, DAC off, ARM set, OSC disabled Supply current VDD = 4.5 V, DAC off, ARM set, OSC enabled VDD = 4.5 V, DAC off, ARM clear, OSC enabled Input offset voltage VDD = 4.5 V, Vref = 1 to 4.25 V F port pullup resistance VDD = 5 V 70 RRTO = 470 KΩ, VDD = 4.5 V, TA = 25°C, Trim deviation ‡ fRTO = 8.192 MHz (PLL setting = 7 Ch) RRTO = 470 KΩ, VDD = 3.5 to 5.2 V, TA = 25°C, Voltage deviation ‡ fRTO = 8.192 MHz (PLL setting = 7 Ch) RRTO = 470 KΩ, VDD = 4.5 V, TA = 0 to 70°C, Temperature deviation ‡ fRTO = 8.192 MHz (PLL setting = 7 Ch) VDD = 4.5 V, TA = 25°C, R(OSC) = 470 KΩ at ±1%, Resistance deviation ‡ fRTO = 8.192 MHz (PLL setting = 7 Ch) TYP 2.4 1.8 0.6 3.3 2.9 0.4 § MAX UNIT V RESET_ V 3 4.5 5.2 1 1.5 1.7 –2 5 –10 20 1 10 10 60 100 50 ±3% ±1.5% VIH V VIL IOH ¶ IOL IOH (DAC) IOL (DAC) Ilkg I(STANDBY) † IDD I(SLEEP-deep) I(SLEEP-mid) I(SLEEP-light) VIO R(PULLUP) ∆f(RTO-trim) ∆f(RTO-volt) ∆f(RTO-temp) ∆f(RTO-res) ¶ V mA mA mA mA µA µA mA µA mV KΩ 0.05 15 0.05 40 60 25 150 ±1% ±0.03 ±1% %/°C † Operating current assumes all inputs are tied to either VSS or VDD with no input currents due to programmed pullup resistors. The DAC output and other outputs are open circuited. ‡ The best trim value is selected at nominal temperature and voltage but the deviation due to the trim error is ignored. § Typical voltage and current measurement taken at 25°C ¶ Cannot exceed 15 mA total per internal VDD pin. Port A, B share 1 internal VDD pin; Port C, D share 1 internal VDD. External Component Absolute Values PARAMETER R(RTO) RTO external resistance C(PLL) PLL external capacitance TEST CONDITIONS TA = 25°C, 1% tolerance TA = 25°C, 10% tolerance MIN MAX 470 3300 UNIT KΩ pF © 2003 Sensory Inc. P/N 80-0210-C 5 SC-614 Data sheet Mechanical Data LQFP 100 PLASTICQUAD FLATPACK (14x14x1.4 mm) Symbol A A1 A2 b b1 c c1 D D1 E E1 L L1 R1 R2 S › ›1 ›2 ›3 Dimension in mm Min Nom Max 1.60 0.05 0.15 1.35 1.40 1.45 0.17 0.22 0.27 0.17 0.20 0.23 0.09 0.20 0.09 0.16 15.85 16.00 16.15 13.90 14.00 14.10 15.85 16.00 16.15 13.90 14.00 14.10 0.50 BSC 0.45 0.60 0.75 1.00 REF 0.08 0.08 0.20 0.20 0º 3.5º 7º 0º 12º TYP 12º TYP Dimension in inch Min Nom Max 0.063 0.002 0.006 0.053 0.055 0.057 0.007 0.009 0.011 0.007 0.008 0.009 0.004 0.008 0.004 0.006 0.624 0.630 0.636 0.547 0.551 0.555 0.624 0.630 0.636 0.547 0.551 0.555 0.20 BSC 0.018 0.024 0.030 0.039 BSC 0.003 0.003 0.008 0.008 0º 3.5º 7º 0º 12º TYP 12º TYP Notes: A. B. C. All linear dimensions are in millimeters. This drawing is subject to change without notice. Falls within JEDEC MS-022 6 P/N 80-0210-C © 2003 Sensory Inc. Data Sheet SC-614 Die Bond-out Coordinates Die Size = 145 x 161 Mil or 3680 x 4094 Microns Pad Size = 256 x 256 Mil Units = Metric Pad 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 © 2003 Sensory Inc. Pin 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 1 5 6 7 8 9 10 11 12 13 14 15 16 18 19 20 21 22 23 24 25 26 27 30 31 32 33 34 35 36 X-Axis Min 3402.53 3402.53 3402.53 3402.53 3402.53 3402.53 3402.53 3402.53 3381.68 3380.92 3402.53 3402.53 3402.54 3402.54 3402.53 3402.53 3402.53 3402.53 3370.73 3174.50 3066.70 2958.55 2825.20 2696.92 2591.16 2486.92 2381.16 2276.92 2171.16 2066.92 1961.16 1632.14 1478.56 1324.98 1171.40 1017.82 864.24 710.66 557.08 430.53 307.37 111.44 111.44 111.44 111.44 111.44 111.44 111.44 Y-Axis Min 1022.32 1176.32 1330.32 1484.32 1638.32 1792.32 1946.32 2100.32 2251.59 2357.47 2509.62 2663.62 2817.62 2971.62 3125.62 3279.62 3433.62 3587.62 3724.61 3795.01 3795.12 3795.01 3795.11 3826.25 3826.25 3826.25 3826.25 3826.25 3826.25 3826.25 3826.25 3816.74 3816.74 3816.74 3816.74 3816.74 3816.74 3816.74 3816.74 3795.88 3795.12 3646.03 3541.18 3434.42 3329.57 3222.81 3117.96 3011.20 X-Axis Max 3488.53 3488.53 3488.53 3488.53 3488.53 3488.53 3488.53 3488.53 3467.68 3466.92 3488.53 3488.53 3488.54 3488.54 3488.53 3488.53 3488.53 3488.53 3456.73 3260.50 3152.70 3044.55 2911.20 2782.92 2677.16 2572.92 2467.16 2362.92 2257.16 2152.92 2047.16 1718.14 1564.56 1410.98 1257.40 1103.82 950.24 796.66 643.08 516.53 393.37 197.44 197.44 197.44 197.44 197.44 197.44 197.44 Y-Axis Max 1108.32 1262.32 1416.32 1570.32 1724.32 1878.32 2032.32 2186.32 2337.59 2443.47 2595.62 2749.62 2903.62 3057.62 3211.62 3365.62 3519.62 3673.62 3810.61 3881.01 3881.12 3881.01 3881.11 3912.25 3912.25 3912.25 3912.25 3912.25 3912.25 3912.25 3912.25 3902.74 3902.74 3902.74 3902.74 3902.74 3902.74 3902.74 3902.74 3881.88 3881.12 3732.03 3627.18 3520.42 3415.57 3308.81 3203.96 3097.20 7 P/N 80-0210-C SC-614 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 111.44 111.44 111.44 111.44 111.44 111.44 111.43 111.47 111.47 111.47 111.47 111.47 111.47 111.47 111.47 132.32 317.80 429.07 540.37 653.76 807.76 961.76 1115.76 1269.76 1423.76 1577.76 1731.76 1883.07 1994.62 2152.96 2306.96 2460.96 2614.96 2768.96 2922.96 3076.96 3230.96 2906.35 2799.59 2688.25 2571.60 2460.30 2349.00 2205.78 2045.34 1891.34 1737.34 1583.34 1429.34 1275.34 1121.34 967.34 265.13 111.24 111.24 111.24 111.27 111.27 111.27 111.27 111.27 111.27 111.27 111.27 132.12 132.88 111.27 111.27 111.27 111.27 111.27 111.27 111.27 111.27 197.44 197.44 197.44 197.44 197.44 197.44 197.43 197.47 197.47 197.47 197.47 197.47 197.47 197.47 197.47 218.32 403.80 515.07 626.37 739.76 893.76 1047.76 1201.76 1355.76 1509.76 1663.76 1817.76 1969.07 2080.62 2238.96 2392.96 2546.96 2700.96 2854.96 3008.96 3162.96 3316.96 2992.35 2885.59 2774.25 2657.60 2546.30 2435.00 2291.78 2131.34 1977.34 1823.34 1669.34 1515.34 1361.34 1207.34 1053.34 351.13 197.24 197.24 197.24 197.27 197.27 197.27 197.27 197.27 197.27 197.27 197.27 218.12 218.88 197.27 197.27 197.27 197.27 197.27 197.27 197.27 197.27 Data sheet Ordering Information Part Ordering P/N Shipping P/N Description SC-614 DIE 65-xxxx-x (ROM specific) Tested, Singulated SC-614 die in waffle pack. SC614-R SC-614 LQFP SC614-RL1 65-xxxx-x (ROM specific) SC-614 100 pin 14x14x1.4mm LQFP 8 P/N 80-0210-C © 2003 Sensory Inc. The Interactive Speech™ Product Line The Interactive Speech line of ICs and software was developed to “bring life to products” through advanced speech recognition and audio technology. The Interactive Speech Product Line was designed for consumer telephony products and cost-sensitive consumer electronic applications such as home electronics, personal security, and personal communication. The product line includes award-winning RSC series general-purpose microcontrollers and tools, SC series of speech microcontrollers, plus a line of easy-to-implement chips that can be pin-configured or controlled by an external host microcontroller. Sensory’s software technologies run on a variety of microcontrollers and DSPs. RSC Microcontrollers and Tools The RSC product line contains low-cost 8-bit speech-optimized microcontrollers designed for use in consumer electronics. All members of the RSC family are fully integrated and include A/D, pre-amplifier, D/A, ROM, and RAM circuitry. The RSC family can perform a full range of speech/audio functions including speech recognition, speaker verification, speech and music synthesis, and voice record/playback. The family is supported by a complete suite of evaluation tools and development kits. SC Microcontrollers and Tools The SC-6x product line feature the highest quality speech synthesis ICs at the lowest data rate in the industry. The line includes a 12.32 MIPS processor for high-quality low data-rate speech compression and MIDI music synthesis, with plenty of power left over for other processor and control functions. Members of the SC-6x line can store as much as 37 minutes of speech on chip and include as much as 64 I/O pins for external interfacing. Integrating this broad range of features onto a single chip enables developers to create products with high quality, long duration speech at very competitive price points. Application Specific Standard Products (ASSPs) Voice Direct™ II provides inexpensive speaker-dependent speech recognition and speech synthesis. This easy-to-use, pinconfigurable chip requires no custom programming and can recognize up to 15 words in 4 pin-programmable modes. Ideal for speakerdependent command and control of household consumer products, Voice Direct™ II is part of a complete product line that includes the IC, module, and Voice Direct™ II Speech Recognition Kit. Voice Extreme™ simplifies the creation of fully custom speech-enabled products by offering developers the capability of programming the chip in a high-level C-like language. Program code, speech data, and even record and playback information can be stored on a single off-chip Flash memory. Based on Sensory's RSC-364 speech processor, Voice Extreme includes a highly efficient on-chip code interpreter, and is supported by a comprehensive suite of low-cost development tools. Software and Technology Voice Activation™ micro footprint software provides advanced speech technology on a variety of microcontroller and DSP platforms. A flexible design with a broad range of technologies allows manufacturers to easily integrate speech functionality into consumer electronic products. Fluent Speech™ small footprint software recognizes up to 50,000 words; offers Animated Speech with the ability to automate enunciation and articulation; performs text-to-speech synthesis in either male or female voices; provides noise and echo cancellation, performs Wordspotting for natural language usage; offers telephone barge-in; and provides continuous digit recognition. Important notices Reasonable efforts have been made to verify the accuracy of information contained herein, however no guarantee can be made of accuracy or applicability. Sensory reserves the right to change any specification or description contained herein. Sensory reserves the right to make changes to or to discontinue any product or service identified in this publication at any time without notice in order to improve design and supply the best possible product. Sensory does not assume responsibility for use of any circuitry other than circuitry entirely embodied in a Sensory product. Information contained herein is provided gratuitously and without liability to any user. Reasonable efforts have been made to verify the accuracy of this information but no guarantee whatsoever is given as to the accuracy or as to its applicability to particular uses. Applications described in this data sheet are for illustrative purposes only, and Sensory makes no warranties or representations that the RSC/SC series of products will be suitable for such applications. In every instance, it must be the responsibility of the user to determine the suitability of the products for each application. Sensory products are not authorized for use as critical components in life support devices or systems. Sensory conveys no license or title, either expressed or implied, under any patent, copyright, or mask work right to the RSC series of products, and Sensory makes balance between recognition and synthesis no warranties or representations that the RSC series of products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Nothing contained herein shall be construed as a recommendation to use any product in violation of existing patents or other rights of third parties. The sale of any Sensory product is subject to all Sensory Terms and Conditions of Sales and Sales Policies. 1991 Russell Ave., Santa Clara, CA 95054 Tel: (408) 327-9000 Fax: (408) 727-4748 © 2003 SENSORY, INC. ALL RIGHT RESERVED. Sensory is registered by the U.S. Patent and Trademark Office. All other trademarks or registered trademarks are the property of their respective owners. www.sensoryinc.com