SDM7101-GC-DN

Specification : TS-S97D022C Date : August , 2000 Technical Specification for Optical Transceiver Module SDM7101-XC SDM7101-GC 155.52Mb/s Short Haul Intermediate Reach Single 5.0 V 1.3 µm Transmitter ( 622.08Mb/s Long Haul Long Reach Single 3.3 V 1.55 µm Receiver 2R / 3R ) ( other __________ other __________ other __________ other __________ Transceiver 2R / 3R ) Sumitomo Electric reserves the right to make changes in this specification without prior notice. #Safety Precaution Symbols This specification uses various picture symbols to prevent possible injury to operator or other persons or damage to properties for appropriate use of the product. The symbols and definitions are as shown below. Be sure to be familiar with these symbols before reading this specification. Warning Caution Wrong operation without following this instruction may lead to human death or serious injury. Wrong operation without following this instruction may lead to human injury or property damage. indicates prohibition of actions. Action details are explained thereafter. indicatescompulsoryactionsorinstructions.Actiondetailsareexplainedthereafter. Example of picture symbols (SDM7101-XC,SDM7101-XC) -1/9- Specification : TS-S97D022C Date : August , 2000 1. General SDM7101-XC / SDM7101-XC-W is a series of compact and high speed performance digital optical transceiver module ideally designed for versatile high speed network applications. 1300nm high speed InGaAsP FP-LD and InGaAs PIN-PD are provided as a light source and a detector, respectively. Transceiver module has PC board mountable package with electrical and optical interfaces. * Data Rate * Duty Cycle * Power Supply Voltage * Electrical Interface * Fiber Coupled Power *Sensitivity * Connector Interface 155.52Mbps,NRZ 50% Single +5.0V PECL -8 ~ -15dBm (Typ. -11dBm) for SMF ~ -34dBm (Typ. -38dBm) SC Duplex Connector The features of SDM7101-XC / SDM7101-XC-W are listed below. * Features Low Power Consumption Low Profile (9.8mm Max) Plastic Molded Package Multi-sourcedFootprint Transmitter...... Uncooled Laser with Automatic Power Control IC Class 1 Laser Product (IEC 825-1 and FDA 21 CFR 1040.10 and 1040.11) Receiver......... Wide Dynamic Range Signal Detect (FLAG) Function 2. Block Diagram Monitor Pin PD LD Automatic Power Control Modulation Current Control TD TDb LD Driver Bias Current Control Current Source Figure 1-1. Block Diagram(Transmitter ) Front-End Amplifier Peak Hold Circuit Limiting Amplifier Comparator SD Output Buffer RDb RD Pin PD Figure 1-2. Block Diagram(Receiver ) (SDM7101-XC,SDM7101-XC) -2/9- Specification : TS-S97D022C Date : August , 2000 3. Package Dimension All dimensions are in mm. 25.4 9.4Max 1.52 3.9 9.8Max 0.8 2.54Px8=20.32 5.5 0.4 Lead pin UNIT:mm 12.7 Figure2-1. Outline Dimensions ( SDM7101-XC ) Notes: 1. Surface of the receptacle and latch levers are metalized. Figure2-2. Outline Dimensions ( SDM7101-GC-ZN / SDM7101-GC-ZW ) (SDM7101-XC,SDM7101-XC) 3.2 2-φ1.5 0.6 15.88 20.32 -3/9- 0.6 Specification : TS-S97D022C Date : August , 2000 All dimensions are in mm. Finger Position Option ( Type-A Finger ) # A B C D E L 0 1 2 3 4 Figure2-3. Outline Dimensions ( SDM7101-GC-#N / SDM7101-GC-#W ) Figure2-4.RecommendedFootprint Caution Do not disassemble this product. Otherwise, failure, electrical shock, overheating or fire may occur. Handle the lead pins carefully. Use assisting tools or prospective aids as required. A lead pin may injure skin or human body (SDM7101-XC,SDM7101-XC) -4/9- Specification : TS-S97D022C Date : August , 2000 4. Pin Assignment No. 1 2 3 4 5 6 7 8 9 RD RDb FLAG(SD) Vccrx Vcctx TDb TD Veetx Symbol Veerx Function Power Supply (-) for Receiver : Connected to GND Differential Data Output (Positive) Differential Data Output (Negative) FLAG (Signal Detect) Power Supply (+) for Receiver : Connected to +5.0V Power Supply (+) for Transmitter : Connected to +5.0V Transmitter Differential Data (Negative) Transmitter Differential Data (Positive) Power Supply (-) for Transmitter : Connected to GND 5. Absolute Maximum Ratings Parameter Storage Case Tem perature Operating Case Teperature Supply Voltage Input Voltage Lead Soldering ( Tem perature) (Time) Symbol Ts Tc Vcc-Vee Vi min. -40 0 -40 0.0 Vee Max 85 70 85 6.0 Vcc+0.5 260 10 Unit °C °C °C V V °C sec. Note 1 1, 2 1, 3 4 5 6 Note 1. No condensation allowed. 2. SDM7101-XC 3. SDM7101-XC-W 4. Vcc>Vee, Vcc=+5.0V, Vee=GND 5. T D, TDb 6. Measured on lead pin at 2mm (0.079in.) off the package bottom Warning Use the product with the rated voltage described in the specification. If the voltage exceeds the maximum rating, overheating or fire may occur. Caution Do not store the product in the area where temperature exceeds the maximum rating, where there is too much moisture or dampness, where there is acid gas or corrosive gas, or other extreme conditions. Otherwise, failure, overheating or fire may occur. (SDM7101-XC,SDM7101-XC) -5/9- 6. Electrical Interface 6-1.Transmitterside Parameter Supply Voltage Supply Current Input Voltage High TD, TDb Low Input Current High TD, TDb Low Signal Input Rise / Fall Time Specification : TS-S97D022C Date : August , 2000 ( Unless otherwise specified, VccTX-VeeTX =VccRX-VeeRX= 4.75 to 5.25 V and all operating temperature shall apply. ) Symbol min. VccTX-VeeTX 4.75 Idtx Vih VccTX-1.17 Vil VccTX-1.95 Iih -10 Iil -10 Typ. 5.00 70 Max. 5.25 150 VccTX-0.73 VccTX-1.45 150 10 1.6 Unit V mA V µA nsec. 3. 20 ~ 80% Note 1 2 2 3 Note 1. Input bias current is not included. 50% duty cycle data. 155.52Mbps 2. VccTX-VeeRX=5.0V, Tc=25°C 6-2. Receiver side Parameter Supply Voltage Supply Current Data & SD High Out put Voltage Low Data Rise / Fall Time of Output Signal SD Assert Time SD Deassert Time Symbol min. VccRX-VeeRX 4.75 Idrx Voh VccRX-1.03 Vol VccRX-1.81 Trd / Tfd Sa Sd Typ. 5.00 60 Max. 5.25 110 VccRX-0.88 VccRX-1.62 1.6 100 350 Unit V mA V nsec µsec µsec Note 1 2 3 4 4 FLAG Output Note 1. Output current is not included. 50% duty cycle data, 155Mbps, NRZ Note 2. Vccrx=+5.0V, Tc=25°C, Output load resistance Rl=50Ω to Vccrx-2V for RD, RDb and SD. Note 3. 20 ~ 80% Note 4. Please refer to Figure 4 Note 5. 50% duty cycle data, 155Mbps, PRBS223-1, NRZ, Pin = -34 ~ -8dBm "H" "L" Pd Pa Optical Input Power 7. Optical Interface 7-1.Transmitterside Figure 4. FLAG Assert Level and Deassert Level ( Unless otherwise specified, Vcc-Vee = 4.75 to 5.25 V and all operating temperature shall apply. ) Symbol Pos Er λc ∆λ min. -15.0 8.2 1261 Typ. -11.0 Max. -8.0 1360 7.7 Refer to Figure 5 Unit dBm dB nm nm Note 1 1 Parameter Average Output Power to SMF Extinction Ratio Center Wavelength Spectral Width ( RMS) Eye Mask for Optical Out put Note 1. Measured at 155.52Mbps PRBS2^23-1, 50% duty cycle data, NRZ 1.20 Normalized Amplitude 1.00 0.80 0.50 0.20 0.00 -0.20 0.00 0.15 0.35 0.65 0.85 1.00 Relation between Input Signal and Optical Output Signal Input Signal TD High Low High Low TDb Low High High Low ON (High) OFF (Low) Undefined Undefined Optical Output Siganl Figure 5. Optical Pulse Mask with Fourth Order Bessel-Thomson Filter Specified in ITU-T G.957 Warning Do not look at the laser beam projection area (e.g. end of optical connector) with naked eyes or through optical equipment while the power is supplied to this product. Otherwise, your eyes may be injured. (SDM7101-XC,SDM7101-XC) -6/9- Specification : TS-S97D022C Date : August , 2000 7-2. Receiver side Parameter Center Wavelength Minimum Sensitivity Overload Flag Assert Level Flag deassert Level Symbol Pmin Pmax Pa Pd min. 1261 -8.0 -48 -49 Typ. Max. 1580 -34.0 -34 -34 Unit nm nm nm dBm dBm Note 1, 2 1, 2 2 -37 -40 Note 1. BER=10^-10, 2. Measured at the bit rate of 155.52Mbps, PRBS 2^23-1, NRZ Note 2. 50% duty cycle data 8. Recommended Inteface Circuit TD 9. VeeTx 8. TD 7. TDb 6. VccTx 5. VccRx 4. SD 3. RDb VccTx R1 R2 Terminate close to Transceiver Inputs R3 C2 R4 TDb C3 C4 L1 C1 Vcc L2 R5 Vcc C5 R11 SD R6 Vcc R7 R8 RDb R9 C6 R10 Terminate close to Device Inputs RD 2. RD 1. VeeRx : Transmission Line with Zo= 50Ω R1 = R3 = R5 = R7 = R9 = 82Ω , R2 = R4 = R6 = R8 = R10 = 130Ω , R11=10Ω C1 = 100 µF, C3 = 2200 pF, C2 = C6 = 0.1 µF, C4 = C5 = 1 µF L1, L2 : Ferrite Bead ZBF 253D-00 (TDK) Figure 6 Recommended Interface Circuit (SDM7101-XC,SDM7101-XC) -7/9- Specification : TS-S97D022C Date : August , 2000 9. Reliability Test Bellcore TA-NWT-000983 Issue 2, December 1993 Heading Test Reference MIL-STD-883 Method 2002 Condition Condition B 5 times/axis 500G, 1.0 ms 1,500G, 0.5ms Vibration MIL-STD-883 Method 2007 Condition A 20 G 20-2,000 Hz 4 min/cycle; 4 cycles/axis ∆T=100°C 20% 20% 20% 11 11 11 0 0 0 --11 11 --0 0 Sampling LTPD SS C SEI Plan SS F/C Mechanical Mechanical Integrity Shock Thermal Shock MIL-STD-883 Method 1011 Solderability Fiber Pull Endurance Accel. Aging (High Temp.) High Temp. Storage Low Temp. Storage Temperature Cycling (R)-453 Section 5.18 ------------------Section 5.20 MIL-STD-883 Method 2003 20% 11 11 11 11 25 10 11 11 0 0 0 0 ----0 0 11 11 ----25 ----11 0 0 ----0 ----0 (steam aging not required) 20% 1 Kg; 3 times;5sec. 2 Kg; 3 times; 5sec. +85C; rated power >5,000hrs. >10,000hrs. max. storage T (T=85°C) >2,000 min. storage T (T=-40°C) >2,000 - 40°C to +85°C 400 times pass/fail 500 times for info. 500 times pass/fail 1000 times for info. 20% --20% --20% 20% ----20% 20% 11 11 11 11 11 11 11 11 ---6 0 --0 --0 0 0 0 ----- ----11 11 11 --11 11 ---6 ----0 0 0 --0 0 OK 0 Damp Heat MIL-STD-202 M103 40°C , 95%, 56days 20% (if using epoxy) or IEC 68-2-3 or 85°C /85%RH 2,000hrs. 20% Cyclic Moisture Section 5.23 Resistance Special Tests Internal Moisture MIL-STD-883 Method 1018 ---------< 5,000 ppm water vapor 20% 20% ------- Flammability TR357:Sec. 4.4.2.5 ----------ESD Threshold Section 5.22 ----------- 10. Laser Safety This product uses a semiconductor laser system and is a laser class 1 product acc. FDA, complies with 21CFR1040. 10 and 1040.11. Also this product is a laser class 1 product acc. IEC 825-1. Class 1 Laser Product Caution If this product is used under conditions not recommended in the specification or this product is used with unauthorized revision, classfication for laser product safety standard is invalid. Classify the product again at your responsibility and take appropriate actions. (SDM7101-XC,SDM7101-XC) -8/9- Specification : TS-S97D022C Date : August , 2000 11. Other Precaution Under such a strong vibration environment as in automobile, the performance and reliability are not guaranteed. The governmental approval is required to export this product to other countries. To dispose of these components, the appropriate procedure should be taken to prevent illegal exportation. This module must be handled, used and disposed of according to your company's safe working practice. Warning Be sure to carry out correct soldering for connection to peripheral circuits in order to prevent contact failure or short-circuit. Otherwise, a strong laser beam may cause eye injury, overheating or fire. Do not put this product or components of this product into your mouth. This product contaions material harmful to health. Caution Be sure to turn the power off when you touch this product connected to the printed circuit boards. Otherwise, electric shock may occur. Dispose this product or equipment including this product properly as an industrial waste according to the regulations. 12. Ordering Information Ordering Number SDM7101-XC SDM7101-XC-W SDM7101-GC-## Connector type SC Duplex Connector, Non-metallized. Operating Temparature Tc = 0 ~ 70°C Tc = -40 ~ 85°C SC Duplex Connector, Metallized. See chart below for detail. SDM7101-GC-# # Operating Case Temperature Option N : 0°C ~ -70°C W : -40°C ~ 85°C EMI Shield Finger Option Z : Without Finger A ~ E : With Type-A Finger *Letter specifies finger position. Refer to Figure2-3 for detail. 13. For More Information U.S.A. ExceLight Communications, 4021 Stirrup Creek Drive, Suite 200 Durham, NC 27703 Tel. +1-919-361-1600 / Fax. +1-919-361-1619 E-mail: info@excelight.com http://www.excelight.com Europe Sumitomo Electric Europe Ltd., 220, Centennial Park, Elstree, Herts, WD6 3SL, United Kingdom Tel. +44-208-953-8681 Fax. +44-208-207-5950 http://www.sumielectric.com Japan Sumitomo Electric Industries, Ltd. ( International Business Division ), 3-12, Moto-Akasaka 1-chome Minato-ku Tokyo 107-8468 Tel. +81-3-3423-5771 / Fax. +81-3-3423-5099 E-mail: product-info@ppd.sei.co.jp http://www.sei.co.jp/Electro-optic/index.html (SDM7101-XC,SDM7101-XC) -9/9-