SPN75-05S

SPN75 75 WATT , Universal Input Fully Enclosed Switching Power Supply ELECTRICAL SPECIFICATIONS All specifications are typical at nominal input, full load. INPUT SPECIFICATIONS Input Voltage.............................................. AC 85-264V Input Frequency.......................................... 47 ~ 63 Hz Input Current.............................................. 0.55 ~ 1.0A Typ Inrush Current (100/230VAC cold start) .................16A ~ 39A Typ Power Factor .............................................. .99 OUTPUT SPECIFICATIONS Output Voltage........................................... See Chart Output Adjustment.................................... ± 10% Efficiency.................................................... 78 ~ 87% Over-Voltage Protection.............................. 115 - 150% Manual Reset Over-Current Protection.............................. Automatic Recovery (105% min) Ripple and Noise........................................ 100 mVp-p max. Hold-Up Time............................................. 40-50 mS Line/Load Regulation.................................. See Chart Rise Time.................................................... 800 - 1700 mS Leakage Current (100/230VAC)........................ 0.75 mA FEATURES POWER FACTOR CORRECTED UNIVERSAL INPUT (AC85-264V) OVERVOLTAGE PROTECTION OVERCURRENT PROTECTION LIGHTWEIGHT CONSTRUCTION METAL CHASSIS WITH COVER COMPACT, LOW-PROFILE PACKAGES 3 YEAR WARRANTY GENERAL SPECIFICATIONS MTBF ......................................................... >160,000 Hours Isolation Voltage Primary to Secondary............... 3000VAC Primary to Case........................ 1500VAC. Secondary to Case.................... 500VAC. Isolation Resistance.................................... 100 M-Ohms min. ENVIRONMENTAL SPECIFICATIONS Operating Temperature .............................. 0˚C~+60˚C Derates Linearly 2.5%/˚C After 50˚C Cooling........................................................ Convection Temperature Coefficient.............................. 0.02% / ˚C Humidity.......................................................20-85% Rh (non-condensing) Storage Temperature.................................. -20˚C ~ +85˚C Shock Vibration.......................................... Shock: 20G (3 directions each 3 times) Vibration: 10 ~ 55Hz SAFETIES / EMI FCC-B EN 55022-B VCCI-II PHYSICAL SPECIFICATIONS Metal Enclosed - Terminal Block 70 Series MODEL SPN75-05S SPN75-12S SPN75-15S SPN75-24S SPN75-48S OUTPUT VOLTAGE 5 VDC 12 VDC 15 VDC 24 VDC 48 VDC CURRENT 85 ~ 264 VAC EFFICIENCY 100VAC 230VAC LINE REGULATION (MV) MAX LOAD REGULATION (mVmax) (0~100% Load) 15.0 A 6.5 A 5.2 A 3.2 A 1.6 A 78% 82% 83% 83% 83% 81% 86% 87% 87% 87% 10 mVmax 10 mVmax 10 mVmax 20 mVmax 20 mVmax 40 mVmax 20 mVmax 20 mVmax 40 mVmax 40 mVmax SPN75 LED V. ADJ. I/O TERMINAL M4 0.591 (15max) 6.378 (162 –1) +V -V (88 –1) 3.465 1.516 (38.5 –1) M4 SCREW THREAD HOLE 1.398 (35.5) 4.508 (114.5 –0.5) 2-No. 6-32UNC (MOUNTING HOLES) NOTE: *MOUNTING SCREWS NOT TO EXCEED MAX. PENETRATION OF 6mm. *REMOVE SHORT BAR BETWEEN (+S) AND (+V) , (-S) AND (-V) WHEN USE REMOTE SENSING. *TOLERANCE –1mm. *ALL DIMENSIONS IN INCH (mm) 0.295 0.709 1.673 INCH 5.787 (147 –0.5) (7.5) SPN 75 NOTE: All specifications typical and nominal / full load and 25˚C unless otherwise noted. Mounting screw lenght should not exceed 0.31 inches or 8 mm. Avoid sustained operation in overload or dead short conditions. Specifications subject to changes without notice. • No. 6-32 mounting holes standard • Dimensions in mm • Terminal block or “pin” type connector available 71 (18) (42.5) FG L N A/C IN 2-No. 6-32UNC (MOUNTING HOLES) BOTTOM