UFL-2LP-04-A-L

SMT Ultra-Miniature Coaxial Connectors - Mating Heights Owing to the Lowest Profile and the Lightest U.FL Series Meets up to 6 GHz Requirement Figure 1. Mating Height Comparison (with Hirose Electric Products) 2.4(2.5Max) U.FL E.FL sFeatures 1. Mating Heights Owing to Lowest Profile Height from the printed circuit board when mates a receptacle with a (right-angle) plug is 2.5 mm maximum. This low Profile is at the world’s shortest level. qSpace Factor of Mated Connector Figure 2. U.FL-LP-040 and U.FL-R-SMT 2. Extremely Small Board Occupation Area Dia.0.81 U.FL-R-SMT U.FL-LP-066 Dia.1.13 Dia.1.32 3. World’s Lightest These are the world’s lightest coaxial connectors. Receptacle: 15.7 mg Right-angle plugs For Ø 0.81 mm cable: 53.7 mg For Ø 1.13 & 1.32 mm cable: 59.1 mg 4. Can Be Used Up to a Frequency of 6 GHz To meet the frequency requirements of a wide variety of miniature equipment, these connectors offer high frequency performance from DC to 6 GHz. Figure 3. U.FL-LP-066and U.FL-R-SMT 5. Can Be Used with Automatic Mounting The embossed tape packaging specification of the receptacles permits automatic mounting. 6. Use of Ultra-Fine Teflon Cable From among the types of suitable cable, Ø 0.8 mm (single shield) outside diameter ultra-fine Teflon coaxial cable has been made a standard specification in consideration of improving the construction qualities and construction area. An external diameter Ø1.32 mm (double shield) & Ø1.13mm (single shield) ultra-fine Teflon coaxial cable specification is also available. 2.5Max 7. Simple Removal of Connectors The extraction jig permits simple removal of connectors. 8. Mating Checks Are Easy Subminiature size notwithstanding, the lock sensation permits a check of sure mating. sApplications Mobile phones, wireless communications equipment, electronic measuring instruments, GPS, wireless LAN, Bluetooth etc. 2002.3 2.5Max In comparison with our E.FL Series of SMT coaxial connectors, the receptacles offer a reduction of approximately 18% of the board occupation area resulting in an area of just 7.7 mm2. U.FL-R-SMT U.FL-LP-040 3.2Max 1 s Product Specifications Ratings Nominal characteristic impedance Rated voltage Rated frequency 50ø 60 V AC (rms) DC to 6 GHz Operating temperature range Operating humidity -40˚C to +90˚C 90% max. Item 1. Contact resistance 2. Insulation resistance 3. Withstand voltage 4. V.S.W.R.* Dia.0.81Cable Dia.1.13Cable Dia.1.32Cable 5. Female contact holding force 0.15 N min. 6. Repetitive operation Contact resistance Specification Center: 20 mø max. Outside: 10 mø max. 500 Mø min. No line or insulation breakdown 1.3 max. 1.35 1.4 1.5 3 to 6 GHz Conditions Measured at 10 mA max. Measured at 100 V DC 200 V AC for 1 minute DC to 3 GHz Measured with a Ø 0.475 pin gauge 25 mø max. (Center) 15 mø max. (Outside) 30 cycles of insertion and disengagement Frequency of 10 to 100 Hz, single amplitude of 1.5 mm, acceleration of 59 m/s2, for 5 cyles in the direction of each of the 3 axes Acceleration of 735 m/s2, 11 ms duration, sine half-wave waveform, for 6 cycles in the direction of each of the 3 axes Temperature of 40˚C, humidity of 95%, let stand for 96 hours Temperature: +40˚C / 5 to 35˚C / +90˚C / 5 to 35˚C Time: 30 min. / Within 5 min. / 30 min. / Within 5 min. Cycles: 5 48 hours continuous exposure to 5% salt water 7. Vibration No momentary disconnections of 1 µs min. No damage, cracks, or parts looseness min. No momentary disconnections of 1 µs min. No damage, cracks, or parts looseness No damage, cracks, or parts looseness Insulation resistance 100 Mø min.(High temperature) Insulation resistance 500 Mø min.(Pry) No damage, cracks, or parts looseness Contact resistance 25 mø max. (Center) 15 mø max. (Outside) No excessive corrosion 8. Shock 9. Humidity resistance 9. (Steady state) 10. Temperature cycle 11. Salt spray test *V.S.W.R. Measurement System The above V.S.W.R. standard values were measured using the measurement system of the diagram below. NOTE 1: Cable type connectors were measured with SMA conversion adapters attached to both ends of the harness product of a suitable 100cm cable. NOTE 2: Board type connectors were mounted to a 50Ω glass epoxy board and measurements were conducted with SMA conversion adapters attached. sMaterials Part Shell Male center contact Female center contact Insulator Plug Receptacle Material Phosphor bronze Brass Phosphor bronze PBT LCP Finish Silver plating Gold plating Gold plating Black Beige Remarks ————— ————— ————— UL94V-0 UL94V-0 2 sPlugs U.FL-LP-040 Form of Plug After Cable Wiring U.FL-LP-066 Item HRS No. Part No. Form of Plug After Cable Wiring Applicable Cable RF-MF5010 Manufactured by Nissei Electric Co., Ltd. J12B0964 Manufactured by Junkosha Co., Ltd. CO-6F-SB-CX50 Manufactured by Hitachi Cable, Ltd. RF-MF5016 Manufactured by Nissei Electric Co., Ltd. J12B1054 Manufactured by Junkosha Co., Ltd. CL331-0452-5 U.FL-LP-066 A12B0733 Manufactured by Junkosha Co., Ltd. CO-6F-DSB-CX-50 Manufactured by Hitachi Cable, Ltd. 59.1/unit Weight (mg) Right-angle plug shell (for Ø 0.81 cable) CL331-0451-2 U.FL-LP-040 53.7/unit Right-angle plug shell (for Ø 1.13 cable) Right-angle plug shell (for Ø 1.32 cable) Please order plugs with the cable assembly specifications. sCable Assembly Dimension of U.FL Series assembly products should be made as indicated below. Single-Ended Cable Assembly Double-Ended Cable Assembly qOrdering Information qCable Assembly Overall Length Standard Tolerance 3 4 Overall Length L (mm) 0035