88E1042H

Transceiver Solutions Alaska® Quad Gigabit Ethernet Transceivers 88E1040/S, 88E1041/S, 88E1042H PRODUCT OVERVIEW The Marvell¨ Alaska¨ family of Gigabit Ethernet (GbE) over copper transceivers are the industryÕs lowest power, smallest form factor, highest performance, and highest port density solutions in volume production. Targeted at high-density GbE switches, the Alaska Quad transceivers are single-chip devices containing four independent GbE PHYs on a single monolithic IC. Each transceiver performs all of the physical layer functions for 100BASE-TX and 1000BASE-T full or half duplex Ethernet on category 5 (CAT 5) twisted pair cable, and 10BASE-T full or half duplex Ethernet on CAT 3, 4 and 5 cable. The Alaska Quad devices (88E1040S, 88E1041S and 88E1042H) offer additional support of 1000BASE-X through an integrated 1.25 GHz Serializer/Deserializer (SERDES). Waveshape Filter 10/100/1000 Transmit PCS Trellis Decoder Decision Feedback Equalizer Fiber Channel Transmit P0_TX_EN P0_TX_ER P0_TXD[7:0] P0_GTX_CLK P0_TX_CLK P0_S_IN+/P0_S_CLK+/P0_S_OUT+/P0_RX_DV P0_RX_ER P0_RXD[7:0] P0_RX_CLK P0_CRS P0_COL XTAL1 XTAL2 RESET# 125CLK D/A P0-MDI[3:0]+/- Echo Canceller Timing Control Near End Crosstalk Canceller Feed Forward Equalizer (parts with ÒSÓ or ÒHÓ option only) Active Hybrid Gain Control Baseline 10BASE-T Receiver P0_MDC P0_MDIO P0_INT# P0_RSET P0_HSDAC+/P0_TSTPT A/D DPLL Registers Auto-Negotiation Skew Control 10/100/1000 Receive PCS JTAG TRST# TCK TDI TMS TDO Management Interface Bias/Test LED/ Configuration P0_LED_LINK10 P0_LED_LINK100 P0_LED_LINK1000 P0_LED_DUPLEX P0_LED_RX P0_LED_TX GCONFIG[0] Clock/Reset Fig 1. Alaska Quad GbE Transceiver Block Diagram FEATURES ¥ Highly integrated 4-port device ¥ Ultra low power, just exceeding 1W/port ¥ 10/100/1000BASE-T IEEE 802.3 compliant ¥ Supports GMII/RGMII/TBI/RTBI interfaces ¥ Virtual Cable TesterTM feature ¥ Integrated 1.25 GHz SERDES (881040S, 88E1041S, 88E1042H) ¥ Media Detect feature automatically detects and configures to either copper or fiber media ¥ Automatic support for 2-pair CAT 5 cable (100 Mbps) ¥ Power management modes ¥ Four RGMII timing modes ¥ User configurable independent Media Access Controller (MAC) interface select BENEFITS ¥ Enables highly integrated Gigabit switches ¥ Enables higher integration and reduced cost ¥ Compatibility with existing installed base of compliant devices ¥ Reduces cost and simplifies PCB layout ¥ Remote cable diagnostics for fault detection ¥ Supports 1000BASE-X fiber applications ¥ Complete media flexibility ¥ ¥ ¥ ¥ Operates over installed 2-pair cable Reduced system power Eliminate the need for on-board delay lines Allows interface flexibility Alaska® Quad Gigabit Ethernet Transceivers FEATURES BENEFITS ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ User programmable individual/group MDC/MDIO support Auto-MDI/MDIX crossover for all modes of operation Support IEEE 1149.1 (JTAG) and NAND-tree ICT Advanced mixed-signal and DSP techniques IEEE 802.3u compliant Auto-Negotiation Active internal hybrids for 1000BASE-T Direct drive LED support Software configurable LED support User programmable PHY address Loopback mode 0.15-micron standard digital CMOS process ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥ Flexible management options Eases installation and reduces cost Simplifies board level testing/debugging Advanced DSP design Automatically configures to 10, 100 or 1000 Mbps Lower cost magnetic Eliminates cost of external LED latches and drivers User-defined LED configuration Works with all existing Gigabit switch designs Assists testing and diagnostics Advanced process for reduced power and cost to achieve the highest port density APPLICATIONS The Marvell Alaska Quad GbE transceivers provide higher port count Gigabit switches, up to 48 ports, offering the industryÕs highest integration and lowest power dissipation. Through integrated SERDES technology, the devices also offer optional support for 1000BASE-SX/LX Gigabit fiber standards, on a per port basis, enabling mixed-media Gigabit switches. These devices support five different PHY/MAC interface options: GMII, RGMII, SGMII, TBI, and RTBI. 10/100/1000 Mbps Ethernet MAC 10/100/1000 Mbps Ethernet MAC 10/100/1000 Mbps Ethernet MAC 10/100/1000 Mbps Ethernet MAC RJ45 Alaska Quad PHY Magnetics RJ45 RJ45 RJ45 Media Types: ¥ 10BASE-T ¥ 100BASE-TX ¥ 1000BASE-T 10/100/1000 Mbps Ethernet MAC 10/100/1000 Mbps Ethernet MAC 10/100/1000 Mbps Ethernet MAC 10/100/1000 Mbps Ethernet MAC Fiber Optics Alaska Quad PHY Fiber Optics Fiber Optics Fiber Optics Media Types: ¥ 1000BASE-LX ¥ 1000BASE-SX MAC Interface Options: ¥ GMII/MII (88E1040/88E1040S and 88E1041/88E1041S only) ¥ TBI (88E1040/88E1040S and 88E1041/88E1041S only) ¥ RGMII ¥ RTBI ¥ SGMII ¥ Serial Interface (88E1040S, 88E1041S and 88E1042H only) MAC Interface Options: ¥ GMII/MII (88E1040S and 88E1041S only) ¥ TBI (88E1040S and 88E1041S only) ¥ RGMII ¥ RTBI Fig 2. Alaska Quad GbE Transceiver Copper Application Diagram Fig 3. Alaska Quad GbE Transceiver Fiber Application Diagram The Marvell Alaska Quad GbE transceivers come with a complete set of hardware and software development tools to assist network hardware engineers with product evaluation. MarvellÕs worldwide field applications engineers collaborate closely with network equipment vendors to develop and deliver new competitive products to market on time. Marvell utilizes recognized world-leading semiconductor foundry and packaging services to reliably deliver high-volume and low cost total solutions. THE MARVELL ADVANTAGE: For more information, visit our website at www.marvell.com. Marvell Semiconductor, Inc. 700 First Avenue Sunnyvale, CA 94089 Phone 408.222.2500 www.marvell.com ©2002 Marvell International Ltd. All rights reserved. Marvell, the Marvell logo, Moving Forward Faster, Alaska, the Galileo logo, and GalNet are registered trademarks of Marvell. Discovery, Fastwriter, Galileo Technology, GalTis, Horizon, Libertas and Prestera are trademarks of Marvell. All other trademarks are the property of their respective owners. 100207-001 04/02