A24110

Series 1 - 110/125A 120/240, 480 Vac • AC Output • Zero Voltage and Random Turn-On Switching • Panel Mount • Internal Snubber Featuring state-of-the-art Surface Mount Technology, these SPST-NO relays deliver proven reliability in the most demanding applications. Output consists of an SCR AC switch and is available in zero-cross, random turn-on (phase controllable) and versions with either AC or DC input (coil) control. Manufactured in Crydom’s ISO 9002 Certified facility for optimum product performance and reliability. HA48110 HD48110 HA48125 HD48125 MODEL NUMBERS AC CONTROL D C C ONTROL A24110 D24110 A24125 D24125 OUTPUT SPECIFICATIONS Œ Operating Voltage (47-63 Hz) [Vrms] Max. Load Current Ž [Arms] Min. Load Current, [mArms] Transient Overvoltage [Vpk] Max. Surge Current, (16.6ms) [Apk] Max. On-State Voltage Drop @ Rated Current [Vpk] Thermal Resistance Junction to Case (RθJC) [˚C/W] Maximum I2 t for Fusing, (8.3 msec.) [A2sec] Max. Off-State Leakage Current @ Rated Voltage [mArms] Min. Off-State dv/dt @ Max. Rated Voltage [V/µsec] Max. Turn-On Time Max. Turn-Off Time Power Factor (Min.) with Max. Load 24-280 110 150 600 1500 1.7 .25 9,340 10 500 24-280 125 150 600 1750 1.7 .22 12,700 10 500 48-530 110 150 1200 1500 1.7 .25 9,340 10 500 48-530 125 150 1200 1750 1.7 .22 12,700 10 500  0.5 1/2 Cycle (DC Control), 10.0 msec (AC Control) 1/2 Cycle (DC Control), 40.0 msec (AC Control) 0.5 0.5 0.5 INPUT SPECIFICATIONS Œ Control Voltage Range Max. Reverse Voltage Max. Turn-On Voltage Min. Turn-Off Voltage Nominal Input Impedance Typical Input Current DC CONTROL (D PREFIX) AC CONTROL (A PREFIX) AC CONTROL (E SUFFIX) 3-32 Vdc -32 Vdc 3.0 Vdc 1.0 Vdc 1500 Ohms (120/240V Models)  3.4mA @ 5 Vdc, 20mA @ 28Vdc 90-280 Vrms (60Hz) --90 Vrms 10 Vrms 60K Ohms 2mA @ 120 Vrms, 4mA @ 240 Vrms 18-36 Vrms --18 Vrms 4.0 Vrms 9.0K Ohms 3mA @ 24 Vrms GENERAL NOTES ©1998 CRYDOM CORP, Specifications subject to change without notice. Œ All parameters at 25ºC unless otherwise specified.  Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1 Ž Heat sinking required, for derating curves see page 2.  Turn-on time for random turn-on versions is 0.02 msec (DC Control Models).  Input circuitry for 480V models incorporates active current limiter with 2mA typical input current.. For recommended applications and more information contact: USA: (800) 8 CRYDOM • (800) 827-9366 • (619) 715-7200 • fax (619) 715-7280 Crydom Corp, 9525 Chesapeake Drive, San Diego, CA 92123 • e-mail: sales@crydom.com WEB SITE: http://www.crydom.com FASTFAX Product Information: (888) 267-9191 UK: (44)1202 812300 • fax (44)1202 812340 Crydom International Ltd., 85, Condor Close, Woolsbridge Industrial Estate, Three-Legged Cross. Wimborne, Dorset, England BH21 6SU GERMANY: (49)871 935405 • fax (49)871 935407, Aussere Parkstr.5, D-84032 Altdorf, Germany 9002 FastFax Document No. 152 110/125.040898, PAGE 1 OF 2 Series 1 - 110/125A 120/240, 480 Vac • AC Output GENERAL SPECIFICATIONS Dielectric Strength 50/60Hz Input/Output/Base Insulation Resistance (Min.) @ 500 Vdc Max. Capacitance Input/Output Ambient Operating Temperature Range Ambient Storage Temperature Range MECHANICAL SPECIFICATIONS Weight: (typical) Encapsulation: Terminals: AVAILABLE OPTIONS E -10 24 Vac Input (18-36 Vac) Example: A24110E Random Turn-On (AC & DC Control) Phase Controllable (DC Control) Example: D24110-10 1.87 (47.5) MOUNTING HOLE/SLOT 0.17 (4.3) DIA. 1.10 (27.9) .45 (11.4) 8-32 TERMINAL (2 PLACES ) 4000 Vrms 109 Ohm 8 pF -40 to 80ºC -40 to 125ºC 3.0 oz. (86.5g) Thermally Conductive Epoxy Screws and Saddle Clamps Furnished, Unmounted 1 OUTPUT 2 SOLID-STATE RELAY -4 INPUT + 3 2.30 (58.4) 1.70 (43.2) Screw Torque Requirements: 6-32 Screws - 10 in./lbs., 8-32 and 10-32 Screws - 20in./lbs. (Screws dry without grease.) All dimensions are in inches (millimeters) Crydom Heat Sinks offer excellent thermal management and are perfectly matched to the load current ratings of Crydom panel mount relays. Request Crydom’s Heat Sink specification sheet for all the details. BASE PLATE .125 (3.2) 1.00 (25.4) 1.80 (45.7) 6-32 TERMINAL (2 PLACES) .78 (19.8) .90 (22.9) CURRENT DERATING CURVES 110A 160 Base Plate Temp [ºC] .4ºC/W 125A 160 90 Power Dissipation .2ºC/W .5ºC/W .4ºC/W 90 .2ºC/W Power Dissipation 120 80 120 80 .5ºC/W 100 1ºC/W 100 1ºC/W 110 40 120 0 30 60 90 120 0 20 40 60 80 Load Current [Arms] Max Ambient Temp. [ºC] 110 40 120 0 30 60 90 120 0 20 40 60 80 Load Current [Arms] Max Ambient Temp. [ºC] ©1998 CRYDOM CORP, Specifications subject to change without notice. APPROVALS UL E116950 FastFax Document No. 152 110/125.040898, PAGE 2 OF 2 For recommended applications and more information contact: USA: (800) 8 CRYDOM • (800) 827-9366 • (619) 715-7200 • fax (619) 715-7280 Crydom Corp, 9525 Chesapeake Drive, San Diego, CA 92123 • e-mail: sales@crydom.com WEB SITE: http://www.crydom.com FASTFAX Product Information: (888) 267-9191 UK: (44)1202 812300 • fax (44)1202 812340 Crydom International Ltd., 85, Condor Close, Woolsbridge Industrial Estate, Three-Legged Cross. Wimborne, Dorset, England BH21 6SU GERMANY: (49)871 935405 • fax (49)871 935407, Aussere Parkstr.5, D-84032 Altdorf, Germany Base Plate Temp [ºC] 9002