AT10PK-12DB20S601

AT10 Series TOCOS ATTENUATORS ® 10mm Square, Single-Turn, Through-Hole Sealed Cermet Attenuators AT10P AT10S AT10PK Features 10mm square, single-turn, through-hole, sealed attenuators Cermet element Top and side adjust styles available Flush single-slot rotor adjustment Optional 20mm or 30mm plastic shaft with knurled, slotted end style 50Ω, 75Ω or 600Ω nominal impedance 6.5dB, 12dB or 20dB nominal attenuation 3 -pin triangular PCB patterns Meets UL 94V-0 flammability requirements Sealed to withstand immersion cleaning Specifications Electrical Nominal Impedance . . . . . . . . . . . . . . . . . . 50Ω, 75Ω, 600Ω Attenuation Range at DC Nominal Attenuation Attenuation Tolerance Minimum Attenuation 6.5dB 0.7dB 0.4dB max. 12dB 1.1dB 0.6dB max. 20dB 1.5dB 1.2dB max. Environmental Temperature Range . . . . . . . . . . . . . . . . . Load Life . . . . . . . . . . . . . . 55 C to 100 C 70 C, 250 hours with rated load ∆ A ) 0.5dB, ∆ I ) 5% Moisture and Load Life . . . . . . . . . . . . . 40 C, 90-95%RH 90 minutes on, 30 minutes off, 0.2 watt, 120 cycles ∆ A ) 0.5dB, ∆ I ) 5% Thermal Shock . . . . . . . . . . . . . . . . . . . . . . 55 C, 100 C, 30 minutes each, 5 cycles without load ∆ A ) 0.5dB, ∆ I ) 5% Shock . . . . . . . . . . . . . 50G, 11ms, 6 directions, 3 times each ∆ A ) 0.5dB, ∆ I ) 5% Vibration . . . . . . . . . . . . . . . . . . 10-55Hz, 1.5mm amplitude, 3 directions, 2 hours each ∆ A ) 0.5dB, ∆ I ) 5% Soldering Heat Resistance . . . . . . . . . . . 350 C, 3 seconds ∆ A ) 0.1dB, ∆ I ) 1% Seal Test . . . . . . . . . . . . . . . . . 85 C, hot water for 1 minute Rotational Life . . . . . . . . . . . . . . . . . . 50 cycles without load ∆ A ) 1dB, ∆ I ) 10% ∆ A = Attenuation Change at DC; ∆ I = Impedance Change Ratio Power Rating . . . . . . . . 0.2 watt at 70 C, 0 watt at 100 C Insulation Resistance . . . . . 100M Ω minimum at 1,000VDC Dielectric Strength . . . . . . . . . . . . . . . . 1,000VAC, 1 minute Adjustment Travel . . . . . . . . . . . . . . . . . . . . . . . . . 140 10 Mechanical Mechanical Travel . . . . . . . . . . . . . . . . . . . . . . . . . 150 10 Shaft Torque . . . . . . . . 25 to 200 gf • cm (0.35 to 2.77 oz • in) Stop Strength . . . . . . . . . . . . . 800 gf • cm (11.09 oz • in) max. Flammability of Plastic Materials . . . . . . . Meets UL 94V-0 Nominal Weight . . . . . . . . . . . . . . . . . . . . . 1.4g (P); 1.7g (S) 1.7g (PK 20mm shaft length) 2.0g (PK 30mm shaft length) Marking . . . . . . . . . . . Impedance, attenuation, dial locators, terminal identification, date code 102 1177 East Tower Road, Schaumburg, IL 60173 TOCOS AMERICA, INC. Tel: 847-884-6664 Fax: 847-884-6665 E-mail: sales@tocos.com www.tocos.com AT10 Series Model Nominal Impedance Nominal Attenuation Frequency Specifications Frequency Range DC ~ 300MHz 6.5dB DC ~ 500MHz DC ~ 300MHz 12dB 0.3 0.2 0.3 A*= 0~10dB: DC ~ 300MHz A*= 10~20dB: 20dB A*= 0~10dB: DC ~ 500MHz A*= 10~20dB: DC ~ 300MHz 0.2 0.3 0.2 0.3 A*= 0~10dB: DC ~ 300MHz A*= 10~20dB: 20dB A*= 0~10dB: DC ~ 500MHz A*= 10~20dB: 6.5dB DC ~ 100kHz DC ~ 100kHz DC ~ 100kHz DC ~ 300MHz 6.5dB DC ~ 500MHz DC ~ 300MHz 12dB 0.4 0.15 0.4 A*= 0~13dB: DC ~ 300MHz A*=13~20dB: 20dB A*= 0~13dB: DC ~ 500MHz 0.4 12 A*=13~20dB: 6.5dB DC ~ 250MHz DC ~ 250MHz DC ~ 250MHz A*=14~20dB: 6.5dB DC ~ 100kHz DC ~ 100kHz DC ~ 100kHz 0.3 0.3 0.3 1.3 23 20.8 20.8 1.15 1.20 1.20 0.2 0.2 A*= 0~14dB: 20dB 0.25 17 1.33 3.0 20 19 1.22 1.25 1.67 0.7 0.15 19 1.25 14 21 13 1.50 1.20 1.58 0.3 0.3 0.3 0.15 4.5 23 20.8 20.8 23 1.15 1.20 1.20 1.15 0.3 16 1.38 2.0 0.2 20 1.15 6.5dB DC ~ 500MHz DC ~ 300MHz 12dB 17 20 16 1.33 1.22 1.38 4.5 23 1.15 0.3 16 1.38 2.0 0.2 20 1.22 14 17 13 1.50 1.33 1.58 Attenuation Flatness dB max. 0.2 Return Loss dB min. 18 VSWR max. 1.29 50 Ω DC ~ 500MHz AT10P & AT10PK 75 Ω DC ~ 500MHz 600 Ω0 12dB 20dB 50 Ω DC ~ 500MHz AT10S 75 Ω 12dB 600 Ω0 12dB 20dB * A = Attenuation TOCOS AMERICA, INC. 1177 East Tower Road, Schaumburg, IL 60173 Tel: 847-884-6664 Fax: 847-884-6665 E-mail: sales@tocos.com www.tocos.com 103 AT10 Series AT10P No Shaft, Flush Single-Slot, Top Adjust P Terminal Style Dimensions AT10S No Shaft, Flush Single-Slot, Side Adjust S Terminal Style Unit: mm AT10PK 13mm or 23mm Plastic Shaft with Knurled, Slotted End Style, Top Adjust, PK Terminal Style AT10PK Shaft Codes and Dimensions Shaft Code 20S 30S Shaft L Housing Length 20mm 30mm A Actual Shaft Length 13mm 23mm Recommended PCB Layouts P & PK Pin-Out S Pin-Out C IN Ø1.0 Electrical Schematic Unit: mm IN R S1 R S2 OUT OUT C 2.5 0.3 max. (3 holes) 2.5 0.3 Ø1.0 max. (3 holes) IN OUT 5.0 0.6 Z IN RP ZO 2.5 0.3 0.6 2.5 0.3 2.5 0.3 0.6 5.0 5.0 C 104 1177 East Tower Road, Schaumburg, IL 60173 TOCOS AMERICA, INC. Tel: 847-884-6664 Fax: 847-884-6665 E-mail: sales@tocos.com www.tocos.com AT10 Series AT 10 PK 20dB 20S 500 Part Numbering System Nominal Impedance Code: Expressed in ohms. A three digit code where the first two digits are significant figures, and the third digit indicates the number of zeros that follow these figures (i.e., 500 = 50 Ω ; 750 = 75 Ω ; 601 = 600 Ω ). Shaft Length: 20S = 13mm Shaft with Knurled, Slotted End Style. 30S = 23mm Shaft with Knurled, Slotted End Style. Blank = No shaft. Nominal Attenuation: 6.5dB ( 0.7 Attenuation Tolerance). 12dB ( 1.1 Attenuation Tolerance). 20dB ( 1.5 Attenuation Tolerance). Dash: Use a dash, with no space before or after the dash, to separate Style and Nominal Attenuation. Example: AT10PK-20dB20S500 Style: P = PCB Mount, No Shaft, Rotor Flush with Housing, 3-Pin Triangular Pattern, Top Adjust. S = PCB Mount, No Shaft, Rotor Flush with Housing, 3-Pin Triangular Pattern, Side Adjust. PK = PCB Mount, Plastic Shaft (available in 2 lengths), 3-Pin Triangular Pattern, Top Adjust Only. Size: 10 = 10mm Square Housing. TOCOS Series Name: AT = Attenuator. Packaging Standard: Bulk Packaging Quantity 100 pieces per box. Soldering and Cleaning Guidelines For soldering, cleaning and other information, refer to the Guidelines and Precautions. TOCOS AMERICA, INC. 1177 East Tower Road, Schaumburg, IL 60173 Tel: 847-884-6664 Fax: 847-884-6665 E-mail: sales@tocos.com www.tocos.com 105