AU9510F

Data Book AU9510F USB Smart Card Reader Controller Technical Reference Manual Product Specification Official Release Revision 1.07W Public AU9510F USB Smart Card Reader Controller V2.00 Official Release-Public Apr 2005 Page 1 of 17 Data Sheet Status Objective specification Preliminary specification Product specification This data sheet contains target or goal specifications for product development. This data sheet contains preliminary supplementary data may be published later. data; This data sheet contains final product specifications. Revision History Date Apr 2005 Revision 1.07W Initial release Description Page 2 of 17 AU9510F USB Smart Card Reader Controller V1.07W Official Release-Public Copyright Notice Copyright 1997 - 2005 Alcor Micro Corp. All Rights Reserved. Trademark Acknowledgements The company and product names mentioned in this document may be the trademarks or registered trademarks of their manufacturers. Disclaimer Alcor Micro Corp. reserves the right to change this product without prior notice. Alcor Micro Corp. makes no warranty for the use of its products and bears no responsibility for any error that appear in this document. Specifications are subject to change without prior notice. Contact Information: Web site: http://www.alcormicro.com/ Taiwan Alcor Micro Corp. 4F, No 200 Kang Chien Rd., Nei Hu, Taipei, Taiwan, R.O.C. Phone: 886-2-8751-1984 Fax: 886-2-2659-7723 Santa Clara Office 2901 Tasman Drive, Suite 206 Santa Clara, CA 95054 USA Phone: (408) 845-9300 Fax: (408) 845-9086 Los Angeles Office 9070 Rancho Park Court Rancho Cucamonga, CA.91730 USA Phone: (909) 483-9900 Fax: (909) 944-0464 Page 3 of 17 AU9510F USB Smart Card Reader Controller V1.07W Official Release-Public Table of Contents 1 Introduction…………………………………………………………….. 1.1 Description…………………………………………………………………………….. 1.2 Features…………………………………………………………………………………. 2 Application Block Diagram…………………………………………. 3 Pin Assignment………………………………………………………… 4.1 Block Diagram…………………………………………………………………… 5 Electrical Characteristics…………………………………………… 6 6 6 7 8 10 11 4 System Architecture and Reference Design………………….. 10 5.1 Recommended Operating Conditions………………………………….. 11 5.2 General DC Characteristics…………………………………………………… 11 5.3 DC Electrical Characteristics for 3.3 volts operation…………… 11 5.4 Crystal Oscillator Circuit Setup for Characterization…………… 12 5.5 ESD Test Results……………………………………………………………………. 12 5.6 Latch-Up Test Results……………………………………………………………. 13 6 Mechanical Information……………………………………………… 15 7 Abbreviations…………..………………………………………………. 16 Page 4 of 17 AU9510F USB Smart Card Reader Controller V1.07W Official Release-Public List of Figures 2.1 Block Diagram…………………………………………………………………………………… 3.1 Pin Assignment Diagram…………………………………………………………………. 4.2 Sample schematics………………………………………………………………… 7 8 11 4.1 AU9510F USB eToken controller Block Diagram……………………………… 10 5.1 Crystal Oscillator Circuit Setup for Characterization……………………… 12 5.2 Latch-Up Test Results Diagram………………………………………………………… 13 6.1 Mechanical Information Diagram……………………………………………………… 15 List of Tables 3.1 Pin Descriptions……………………………………………………………………………….. 5.1 Recommended Operation Condition……………………………………………… 9 11 5.2 General DC Characteristics……………………………………………………………… 11 5.3 DC Electrical Characteristics for 3.3 volts operation………………………. 11 5.4 ESD Data…………………………………………………………………………………………… 12 5.5 Latch-Up Data Table………………………………………………………………………… 14 Page 5 of 17 AU9510F USB Smart Card Reader Controller V1.07W Official Release-Public 1.1. 1.0. Introduction Description AU9510F is a highly integrated single chip, USB Smart Card reader controller. Highly integration enables the lowest BOM cost of USB Smart Card reader. The AU9510F supports multiple international standards including ISO7816 for IC card standard, PC/SC 1.0 for windows smart card standard, Microsoft WHQL, and USB-IF CCID standard. The application of AU9510F can be generally applied to Smart Card read/write terminal device, such as Electronic Cash, Credit and Debit, GSM, loyalty system, and access information...etc. 1.2. Feature • Support the Universal Serial Bus Specification, version 1.1. • Based on ISO7816 implementation • Support PC Smart Card industry standard – PC/SC 1.0 • Support Microsoft Smart Card for Windows • Meet Microsoft WHQL USB Smart Card Reader requirements • Include WDM driver to work on Windows 98 and Windows 2000 • Support dual slots for higher security application • Support T0, T1 protocol, I2C memory card, SLE4418, SLE4428, SLE4432, SLE4442, AT88SC1608 and AT45D041 card. • Dedicated hardware block implementation for IC and memory card protocols for highest performance • Implemented as an USB full speed device with bulk transfer endpoint • Built-in 3.3V regulator for single 5V operation • Built-in PLL for USB and Smart Card clocks requirement • Support EEPROM for USB descriptors customization, including VID/PID • Available in 48-LQFP Package • Based on USB-CCID class, short APDU level • Compatible with Microsoft USB-CCID driver • Support 3V/5V card Page 6 of 17 AU9510F USB Smart Card Reader Controller V1.07W Official Release-Public 2.0. Application Block Diagram AU9510F is a highly integrated single chip, which is used as an USB Smart Card reader or in an embedded USB device in the downstream port of an USB hub. Following is the application diagram of a typical card reader product with AU9510F. By connecting the card reader to a GSM or Corporate network…etc. 2.1 Block Diagram Figure 2.1 Block Diagram P C w ith U S B H o s t C o n tro lle r A p p lic a tio n P ro g ra m s C o rp o ra te N e tw o rk Access In te rn e t/In tra n e t A c c e s s E le c tro n ic C a s h C re d it a n d D e b it L o y a lty GSM U S B K e y b o a rd H u b USB D own s tre a m P o rt USB S m a rtC a rd Reader IS O 7 8 1 6 C o m p lia n t S m a rt C a rd S m a rt C a rd S o lu tio n s Smart card Page 7 of 17 AU9510F USB Smart Card Reader Controller V1.07W Official Release-Public 3.0. Pin Assignment The AU9510F is packed in 48-LQFP-form factor. The following figure shows signal name for each pin and the table in the following page describes each pin in detail Figure 3.1 Pin Assignment Diagram ICC0DETN SC0DATA SC0CLK SC1RST SC1CLK SC1FCB SC0FCB SC0RST 48 VCCA SC0C8 47 SC0C6 SC1C8 SC1C6 46 45 44 43 42 41 40 39 38 37 36 SCARD1DATA 1 GNDA 2 35 ICC1DETECTN XTAL1 3 34 NC XTAL2 4 33 PROM_DATA7 PSWOUTB 5 ALCOR MICRO AU9510F 48PIN LQFP 32 PROM_DATA6 PSWOUTA 6 31 PROM_DATA5 VCC5V 7 30 PROM_DATA4 VCC3V 8 29 PROM_DATA3 USB_DP 9 28 PROM_DATA2 USB_DM 10 27 GNDK GNDIO 11 12 13 14 15 16 17 18 19 20 21 22 23 24 26 VCCK GPI_0 25 PROM_DATA1 AU9510F USB Smart Card Reader Controller V1.07W Official Release-Public GPI_1 PORT1_2 PORT1_1 PORT1_6 PORT1_0 PORT1_5 SDA PORT1_4 SCL PROM_DATA0 PORT1_3 PORT1_7 Page 8 of 17 Table 3.1 Pin Descriptions Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 Pin Name VCCA GNDA XTAL1 XTAL2 PSWOUTB PSWOUTA VCC5V VCC3V USB_DP USB_DM GNDIO GPI_0 GPI_1 SCL SDA NC PORT1_1 PORT1_2 PORT1_3 PORT1_4 PORT1_5 PORT1_6 PORT1_7 PROM_DATA0 PROM_DATA1 VCCK GNDK PROM_DATA2 PROM_DATA3 PROM_DATA4 PROM_DATA5 PROM_DATA6 PROM_DATA7 NC ICC1DETN SC1DATA SC1CLK SC1RST SC1FCB SC1C6 SC1C8 ICC0DETN SC0DATA SC0CLK SC0RST SC0FCB SC0C6 SC0C8 I/O PWR PWR I O O O PWR PWR I/O I/O PWR I I I/O I/O I/O O O O I I I I/O I/O PWR PWR I/O I/O I/O I/O I/O I/O I I/O I/O I/O I/O I/O I/O I I/O I/O I/O I/O I/O I/O Description Analog 3.3V power supply Analog ground. Crystal Oscillator Input (12MHz). Crystal Oscillator Output (12MHz). Connect to Slot1 Power. - Not support in this version Connect to Slot0 Power. 5V power supply Input 3.3V power supply output USB D+ USB DChip I/O Ground. Reserved (need pull Low) Reserved (need pull down) EEPROM Clock (need pull high) EEPROM Data (need pull high) General IO 1 Slot1 LED Slot2 LED - Not support in this version Device LED Reserved (need pull Low) Reserved (need pull Low) General Input 7 Rom data 0 Rom data 1 Core power supply 3.3V Core ground Rom data 2 Rom data 3 Rom data 4 Rom data 5 Rom data 6 Rom data 7 Smart card 1 inserted (Low true) (pull high) - Not support in this version Smart card 1 serial data - Not support in this version Smart card 1 clock - Not support in this version Smart card 1 reset Smart card 1 GPIO_0 - Not support in this version Smart card 1 GPIO_1 - Not support in this version Smart card 1 GPIO_2 - Not support in this version Smart card 0 inserted (Low true)(pull high) Smart card 0 serial data Smart card 0 clock Smart card 0 reset Smart card 0 GPIO_0 Smart card 0 GPIO_1 Smart card 0 GPIO_2 Page 9 of 17 AU9510F USB Smart Card Reader Controller V1.07W Official Release-Public 4.0. System Architecture and Reference Design 4.1. Block Diagram Figure 4.1 AU9510F USB USB Smart Card Reader Controller USB Upstream Port XCVR USB SIE USB FIFO RAM Smart Card Control Card Eject Card Reset Card Insert Processor ROM EEPROM Interface Smart Card FIFO Card Data Card Clock 3.3 Card Power 3.3V Voltage Regulator Optional 256 Bytes EEPROM 12MHz XTAL Reset Page 10 of 17 AU9510F USB Smart Card Reader Controller V1.07W Official Release-Public 5.0. Electronic Characteristics 5.1 Recommended Operation Condition Table 5.1 Recommended Operation Condition SYMBOL VCC VIN TOPR TSTG PARAMETER Power Supply Input Voltage Operating Temperature Storage Temperature MIN 4.75 0 0 -40 TYP 5 MAX 5.25 VCC 85 125 UNITS V V O O C C 5.2 General DC Characteristics Table 5.2 General DC Characteristics SYMBOL IIL IIH IOZ CIN COUT CBID PARAMETER Input low current Input high current Tri-state leakage current Input capacitance Output capacitance Bi-directional buffer capacitance CONDITIONS no pull-up or pull-down no pull-up or pull-down MIN -1 -1 -10 5 5 5 TYP MAX 1 1 10 UNITS µA µA µA ρF ρF ρF 5.3 DC Electrical Characteristics for 3.3 volts operation Table 5.3 DC Electrical Characteristics for 3.3 volts operation SYMBO VIL VIH VOL VOH RI PARAMETER Input Low Voltage Input Hight Voltage CONDITIONS CMOS CMOS 2.3 0.4 2.4 10K/200K MIN TYP MAX 0.9 UNITS V V V V KΩ Page 11 of 17 AU9510F USB Smart Card Reader Controller V1.07W Official Release-Public Output low voltage IOL=4mA, 16mA Output high voltage IOH=4mA,16mA Input Pull-up/down resistance Vil=0V or Vih=VCC 5.4 Crystal Oscillator Circuit Setup for Characterization The following setup was used to measure the open loop voltage gain for crystal oscillator circuits. The feedback resistor serves to bias the circuit at its quiescent operating point and the AC coupling capacitor, Cs, is much larger than C1 and C2. Figure 5.1 Crystal Oscillator Circuit Setup for Characterization 5.5 ESD Test Results Test Description: ESD Testing was performed on a Zapmaster system using the Human-Body-Model (HBM) and Machine-Model (MM), according to MIL-STD 883 and EIAJ IC-121 respectively. • Human-Body-Model stresses devices by sudden application of a high voltage supplied by a 100pF capacitor through 1.5k-ohm resistance. • Machine-Model stresses devices by sudden application of a high voltage supplied by a 200pF capacitor through very low (0 ohm) resistance. Test Circuit & Condition - Zap Interval: 1 second - Number of Zaps: 3 positive and 3 negative at room temperature - Criteria: I-V Curve Tracing Table 5.4 ESD Data Model HBM MM Mode Vdd, Vss, I/C Vdd, Vss, I/C S/S 15 15 Target 6000V 200V Results PASS PASS Page 12 of 17 AU9510F USB Smart Card Reader Controller V1.07W Official Release-Public 5.6 Latch-Up Test Results Test Description: Latch-Up testing was performed at room ambient using an IMCS-4600 system which applies a stepped voltage to one pin per device with all other pins open except Vdd and Vss which were biased to 5Volts and ground respectively. Testing was started at 5.0V (Positive) or 0V (Negative), and the DUT was biased for 0.5 seconds. If neither the PUT current supply nor the device current supply reached the predefined limit (DUT=00mA, Icc=100mA), then the voltage was increased by 0.1Volts and the pin was tested again. This procedure was recommended by the JEDEC JC-40.2 CMOS Logic standardization committee. Notes: 1. 2. DUT: The device under test. PUT: The pin under test. Figure 5.2 Latch-Up Test Results Diagram Test Circuit: Positive Input/Output Overvoltage/Overcurrent Test Circuit: Negative Input/Output Overvoltage/Overcurrent Page 13 of 17 AU9510F USB Smart Card Reader Controller V2.00 Official Release-Public Figure 5.2 Latch-Up Test Results Diagram (continue) Supply Overvoltage Test Table 5.5 Latch-Up Data Table Mode Voltage Current + + Voltage (V)/Current (mA) 11.0 11.0 200 200 9.0 S/S 5 5 5 5 5 Results Pass Pass Pass Pass Pass - Vdd - Vxx Page 14 of 17 AU9510F USB Smart Card Reader Controller V2.00 Official Release-Public 6.0. Mechanical Information Figure 6.1 Mechanical Information Diagram Page 15 of 17 AU9510F USB Smart Card Reader Controller V2.00 Official Release-Public 7.0. Abbreviation This chapter lists and defines terms and abbreviations used throughout this specification. WHQL Windows Hardware Quality Labs EMV ATM BOM VID PID PLL ESD Europay MasterCard Visa Automatic Teller Machine Bill of Material Vendor ID Product ID Phase Lock Loop Electrostatic Sensitive Device PC/SC This is association name.( http://www.pcscworkgroup.com/) GSM ..Globe System for Mobile Communication Page 16 of 17 AU9510F USB Smart Card Reader Controller V2.00 Official Release-Public 【MEMO】 About Alcor Micro, Corp Alcor Micro, Corp. designs, develops and markets highly integrated and advanced peripheral semiconductor, and software driver solutions for the personal computer and consumer electronics markets worldwide. We specialize in USB solutions and focus on emerging technology such as USB and IEEE 1394. The company offers a range of semiconductors including controllers for USB hub, integrated keyboard/USB hub and USB Flash memory card reader…etc. Alcor Micro, Corp. is based in Taipei, Taiwan, with sales offices in Taipei, Japan, Korea and California. Alcor Micro is distinguished by its ability to provide innovative solutions for spec-driven products. Innovations like single chip solutions for traditional multiple chip products and on-board voltage regulators enable the company to provide cost-efficiency solutions for the computer peripheral device OEM customers worldwide. Page 17 of 17 AU9510F USB Smart Card Reader Controller V2.00 Official Release-Public