FAD1531220

Dupline® Field- and Installationbus Receiver with Analog Current Output Types FAD 1530, FAD 1531, FAD 1532 • Receivers with current signal output • Current output signals: FAD 1530: 1 x 0 to 1 mA FAD 1531: 1 x 0 to 20 mA FAD 1532: 1 x 4 to 20 mA • 8-bit (8 channels) resolution • For binary transmitted analogue signals • Galvanically separated output • D-housing • Plug-in type module • AC power supply Product Description Dupline analog receivers with standard current output signals (0 to 1 mA, 0 to 20 mA, 4 to 20 mA). Convert binary codes into analog current signals. Ordering Key Type: Dupline Output signal Supply FAD 1530 024 Type Selection Supply 24 VAC 120 VAC 220 VAC Code module Ordering no. 0 to 1 mA FAD 1530 024 FAD 1530 120 FAD 1530 220 FMK A to FMK P Ordering no. 0 to 20 mA FAD 1531 024 FAD 1531 120 FAD 1531 220 FMK A to FMK P Ordering no. 4 to 20 mA FAD 1532 024 FAD 1532 120 FAD 1532 220 FMK A to FMK P Output Specifications FAD 1530 ... Output Signal range Isolated in groups of Output load resistance Resolution Settling time Short-circuit protection Short-circuit current Open loop voltage Inaccuracy Cable length Dielectric voltage Output - Dupline 1 current output 0 to 1 mA 1x1 ≤ 10 kΩ 8 bits (3.92 µA/LSB) ≤ 1 pulse train + 10 ms Yes 1 mA Approx. 15 V ≤ 1% of full scale ≤3m ≥ 200 VAC (rms) FAD 1531 ... 1 current output 0 to 20 mA 1x1 ≤ 350 Ω 8 bits (78.43 µA/LSB) ≤ 1 pulse train + 10 ms Yes 20 mA Approx. 15 V ≤ 1% of full scale ≤3m ≥ 200 VAC (rms) FAD 1532 ... 1 current output 4 to 20 mA 1x1 ≤ 350 Ω 8 bits (62.75 µA/LSB) ≤ 1 pulse train + 10 ms Yes 20 mA Approx. 15 V ≤ 1% of full scale ≤3m ≥ 200 VAC (rms) Specifications are subject to change without notice (01.09.99) 1 FAD 1530, FAD 1531, FAD 1532 Supply Specifications Power supply Rated operational voltage through pins A1 & A2 220 120 024 Frequency Voltage interruption Rated operational power Rated impulse 220 withstand voltage 120 024 Dielectric voltage Supply - Dupline Supply - Output Overvoltage cat. III (IEC 60664) 230 VAC +6%, -15% (IEC 60038) 120 VAC ± 10% (IEC 60038) 24 VAC ± 10% 45 to 65 Hz ≤ 40 ms Typ. 2.5 VA 4 kV 2.5 kV 800 V ≥ 2 kVAC (rms) ≥ 2 kVAC (rms) General Specifications Output OFF delay upon loss of Dupline carrier Power ON delay Environment Degree of protection Pollution degree Operating temperature Storage temperature Humidity (non-condensing) Mechanical resistance Shock Vibration Dimensions Material (see "Technical Information") Weight Approvals Undefined Undefined, ≤ 1 s IP 20 3 (IEC 60664) -20° to +50°C (-4° to +122°F) -50° to +85°C (-58° to +185°F) 20 to 80% 15 G (11 ms) 2 G (6 to 55 Hz) D-housing 200 g CSA, UL Mode of Operation Receiver with current signal output. The binary status of an entire channel group (8 bit) is converted to a current signal. The binary status of the selected group may be generated by Dupline transmitters with analog inputs (current, voltage, temperature etc.) or by PC’s. The least significant bit (influencing the output current by 0.392% of full scale) is the highest channel of the selected group (C8 if FMK C is plugged in). The most significant bit (influencing the output current by 49.8% of full scale) is the lowest channel of the selected group (C1 in the above example). Note: Analog receivers must not be used in systems where channel generators with 2 or 3 sequences are installed. Operation Diagram Output signal MSB = Most Significant Bit LSB = Least Significant Bit Channel status Wiring Diagram Accessories Socket◊ Socket cover Hold down spring◊ Front mounting bezel DIN-rail for D 411 D 411 BB 5 HF FRS 2 FMD 411 For further information refer to "Accessories". Load S: signal wire. Power Supply 2 Specifications are subject to change without notice (01.09.99)