IR333C-A

DEVICE NUMBER : ECN : DIR-033-007 REV : 1.2 PAGE : 1/8 5mm Infrared LED MODEL NO :
Features :
High radiant intensity
Peak wavelength p=940nm
View angle 20
High reliability
2.54mm Lead spacing IR333C-A
Description :
Infrared Emitting Diode (IR333C-A) is a high intensity diode, molded in a water clear plastic package. The device is spectrally matched with phototransistor, photodiode and infrared receiver module.
Applications :
Free air transmission system
Optoelectronic switch
Floppy disk drive
Infrared applied system
Smoke detector CHIP PART NO. IR MATERIAL GaAlAs LENS COLOR Water clear DEVICE NUMBER : ECN : DIR-033-007 REV : 1.2 PAGE : 2/8 5mm Infrared LED MODEL NO : IR333C-A
Package Dimensions :
Notes : 1.All dimensions are in millimeter. 2.Protruded resin under flange 1.5 mm Max. 3.Lead spacing is measured where the lead emerge from the package. 4.Lens color
Water clear. 5.Above specification may be changed without notice. We will reserve authority on material change for above specification. 6.These specification sheets include materials protected under copyright of corporation . Please don’t reproduce or cause anyone to reproduce them without consent. 7.When using this product , please observe the absolute maximum ratings and the instructions for use outlined in these specification sheets. We assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. DEVICE NUMBER : ECN : DIR-033-007 REV : 1.2 PAGE : 3/8 5mm Infrared LED MODEL NO : IR333C-A  Absolute Maximum Ratings at TA = 25 Parameter Symbol Rating Continuous Forward Current Peak Forward Current Pulse width=100s, Duty cycle=1 Reverse Voltage Operating Temperature Storage Temperature Soldering Temperature Power Dissipation at(or below) 25Free Air Temperature IF IFP VR Topr Tstg Tsol Pd 50 1.0 5 -40 ~ +85 -40 ~ +85 260 100 Unit mA A V     Notice 4mm from mold body less than 5 seconds  Electronic Optical Characteristics : Parameter Symbol Min. Typ. Max. 7.8 ---------------------------20 85 750 940 45 1.2 1.4 2.6 ---20 ---------------1.5 1.85 4.0 10 ---- Unit Condition IF=20mA IF=100mA,tp=100s, tP/T=0.01 IF=1A,tp=100s, tP/T=0.01 IF=20mA IF=20mA IF=20mA IF=100mA,tp=100s, tP/T=0.01 IF=1A,tp=100s, tP/T=0.01 VR=5V IF=20mA Radiant Intensity Peak Wavelength Spectral Bandwidth Forward Voltage Reverse Current View Angle Ee P  mW/sr nm nm VF IR 2 1/2 V A deg DEVICE NUMBER : ECN : DIR-033-007 REV : 1.2 PAGE : 4/8 5mm Infrared LED MODEL NO : IR333C-A
Typical Electrical/Optical/Characteristics Curves
 
 
 


   DEVICE NUMBER : ECN : DIR-033-007 REV : 1.2 PAGE : 5/8 5mm Infrared LED MODEL NO : IR333C-A
Typical Electrical/Optical/Characteristics Curves




 


 
 
  
 




   


  

 DEVICE NUMBER : ECN : DIR-033-007 REV : 1.2 PAGE : 6/8 5mm Infrared LED MODEL NO : IR333C-A  Reliability Test Item And Condition The reliability of products shall be satisfied with items listed below. Confidence level:90% LTPD:10% NO. Item Test Conditions Test Sample Failure Ac/Re Hours/ Size Judgement Cycles Criteria 1 Solder Heat TEMP : 260 ± 5  5 secs 22 pcs IR 2  0.8 VF 1.2 0/1 H : +85 30 mins 2 Temperature Cycle 5 mins L : -55 H : +100 50 cycles 22 pcs 0/1 30 mins 5 mins 3 Thermal Shock 10 secs L : -10 5 mins 50 cycles 22 pcs U :Upper specification limit L :Lower specification limit 0/1 4 5 6 7 High Temperature TEMP. : +100 Storage Low Temperature TEMP. : -55 Storage DC Operating Life IF=20mA High Temperature / 85 / 85% R.H. High Humidity 1000 hrs 1000 hrs 1000 hrs 1000 hrs 22 pcs 22 pcs 22 pcs 22 pcs 0/1 0/1 0/1 0/1 DEVICE NUMBER : ECN : DIR-033-007 REV : PAGE : 1.2 7/8 5mm Infrared LED MODEL NO : IR333C-A
Test Method For Power : Condition :

 Test Item :    
   Unit : mW/sr
To Distinguish Intensity: Condition:IF=20mA Bin Number Min Max M 7.80 12.50 N 11.00 17.60 P 15.00 24.00 Q 21.00 34.00 DEVICE NUMBER : ECN : DIR-033-007 REV : 1.2 PAGE : 8/8 5mm Infrared LED MODEL NO : IR333C-A
Packing Specifications