NSVS806

NSVS806 Dec-01 JRC SAW FILTER NSVS806 Application 426.42MHz Remote Unlocking Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig.1. Table 1. Electrical Specifications Item Spec. Typical Input and Output Impedance 50Ω Nominal Center Frequency (f0) 426.42MHz Insertion Loss 425.92~426.92MHz 3.0dB max. 1.9dB Response Variation 425.92~426.92MHz 1.5dB max. 0.6dB Input and Output VSWR 425.92~426.92MHz 2.5 max. 1.8 Out of Band Rejection 405.02MHz 45dB min. 50dB (Relative to Through Level) 447.82MHz 45dB min. 50dB (Operating Temperature Range: -20~+70ºC) Maximum Rating: (Table 2) Table 2. Maximum Ratings Item Maximum Input Power Maximum DC Voltage Operating Temperature Range Storage Temperature Rating +20dBm 7.5V -20~+70ºC -30~+80ºC Mechanical Specifications: (Fig.2) Package is designed as small as 3.5x3.5x1.0[mm3] for SMD (Surface Mount Device) type. Notice: This part is electrostatic discharge sensitive and may be damaged by improper handling. Communications Equipment Division Communications Equipment Marketing Department 17-22 Akasaka 2-chome minato-ku, Tokyo. 107-0052 Japan Tel. +81 3-3584-8811 Fax. +81 3-3584-8876 http://www.jrc.co.jp/product/comm/deveice/saw/saw_top.html (Japanese) http://www.jrc.co.jp/product/comm/device/saw/saw_top_e.html (English) NSVS806 Dec-01 IN 50Ω 1 8 7 OUT 50Ω 2 SAW 6 3 4 5 (a) (1) Fig.1 Measuring circuit 3.5±0.2 (b) 3 .5 ±0 .2 J18 GN (3) (0.95) (2) 4 (0.8) [5x] (0 .6 ) 5 (0.6) [8 x ] 3 Marking (1) Manufacture’s Mark (2) Lot Number (a) Year (b) Month *Oct.--- X Nov.--- Y Dec.--- Z (3) Part number Mark Pin no. 1 2 3 4 5 6 7 8 Connection GND IN/OUT GND GND GND OUT/IN GND GND 1 .0 ±0 .2 (2 .54) (1 .2 7 ) 2 6 (1.0) [2 x ] 1 8 7 Fig.2 Package dimensions (in mm) 4.3 0.6 1.2 [6x] 4.3 1.27 1.27 Via -Hole(Φ 0.3) Fig.3 Desirable land area (in mm) 0.6 [6x] NSVS806 Dec-01 Notice 1. Use this component within operating temperature range. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -20ºC or more than +70ºC, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. 2. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350ºC max., the time of soldering: 10 seconds max., the power of soldering iron: 30W max.. 3. Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. 4. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. 5. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned. 6. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. And do not transport this component with bare hand. 7. As it might be a cause of degradation or destruction to apply D.C. voltage between each terminal, apply D.C. voltage 7.5V max. in actual circuit. Note 1. This specification specifies the quality of this component as a single unit. Make sure that this component is evaluated and confirmed against this specification when it is mounted to your products. 426.42MHz Remote Unlocking FREQUENCY CHARACTERISTICS S21 0 1 2 Insertion Loss[dB] 3 4 5 6 7 8 9 10 Center 426.42 Frequency [MHz] S11 S22 0 10 20 30 40 50 60 70 80 90 100 Span 10 , 100 S11 11 10 9 8 7 6 5 4 3 2 1 Center 426 0 10 20 Insertion Loss [dB] 30 40 50 60 70 80 90 100 0 1500 Frequency [MHz] S22 11 10 9 8 7 6 5 4 3 2 1 Center 426 Span 25 [MHz] VSWR Span 25 [MHz] VSWR 3000