ODP-43-PE-1250-SCX-R

FSAN High Power Diplexer PRELIMINARY ODP-43-PE Features • Low cost 1490 DFB TX, 1310 nm RX design • High Isolation • 0 to 70˚C operation • TX data rates up to 1250 Mbps • Multiple Burst Receive TIA versions available • Compliant to ITU-T G.983.3 FSAN @ 155 and 622 Mbps Absolute Maximum Ratings Parameter Operating Temperature(case) Storage Temperature Min 0 -40 Typical Max 70 85 Units ºC ºC Module Requirements Parameter 1490 TX to 1310 RX crosstalk Back Reflection @ 1310 nm Back Reflection @ 1490 nm Min Typical -60 -20 -6 Max -47 -20 -6 Units dB dB dB Transmitter Requirements Parameter Wavelength Spectral Width (-20 dB) Side Mode Supression ratio 1/2 Ppeak set point @ 25ºC (FSAN) 1/2 Ppeak over temp and EOL (FSAN) Bias Current Bias Current@EOL Modulation Current PD Monitor Current Forward Voltage Rise/Fall Time a PD Dark Current PD Capacitance a 10% Symbol λ ∆λ SMSR Pset Pave Ibias Ibias,EOL Imod IPD,mon Vf tr/tf IPD, dark CPD Min 1480 30 -0.5 6 10 50 - Typical 1490 1.5 1.2 10 Max 1500 1 4 70 100 80 1000 1.8 0.5 1 15 Units nm nm dB dBm dBm mA mA mA µA Volts ns µA pF to 90% FSAN High Power Diplexer PRELIMINARY ODP-43-PE Digital Receiver Characteristics (155 Mbps) Parameter Detection Wavelength Gain differential Supply Voltage Supply Current (Vcc= 5V)a Supply Current (Vcc= 3.3V)a High Frequency -3 dB pointb Single-ended output voltage(p-p)c Single-ended output resistanced Symbol λ G Vcc Icc Icc f-3dB(h) Vo(se)(p-p) Ro(se) Min 1260 20 3 20 20 100 40 36 Typical 5.0 38 35 130 110 44 Max 1360 5.5 60 50 200 57 Units nm mV/µW V mA mA MHz mV Ohm a) AC Coupled; RL= 50 Ohm b) AC coupled; measured differentially; Ci =0.7 pF; RL =50 Ohm; Tj= 100ºC c) AC coupled; RL = 50 Ohm; input current =100 µA(p-p) d) DC tested Digital Receiver Characteristics (622 Mbps) Parameter Detection Wavelength Gain differential Supply Voltage Supply Current (Vcc= 5V)a Supply Current (Vcc= 3.3V)a High Frequency -3 dB point (Vcc= 5V)b High Frequency -3 dB point (Vcc= 3.3V)b Single -ended output voltage(p-p)c Single-ended output resistanced a) AC coupled; RL =50 Ohm b) Ci= 0.7 pF c) AC coupled; RL = 50 Ohm; input current =100 µA(p-p) d) DC tested Symbol λ G Vcc Icc Icc f-3dB(h) f-3dB(h) Vo(se)(p-p) Ro(se) Min 1260 10 3 23 20 450 440 75 40 Typical 5.0 28 28 580 520 200 50 Max 1360 5.5 45 42 750 600 330 62 Units nm mV/µW V mA mA MHz MHz mV Ohm FSAN High Power Diplexer PRELIMINARY ODP-43-PE Mechanical Drawing Receiver Block Diagram Vcc 10 µF + 1nH 0.01 µF 1 4 C C 2 OUT - OUT + At 155 Mbps, C= 0.1µF At 622 Mbps, C= 0.1 µF At 1250 Mbps, C= 0.022 µF 3 Luminent Optical block Customer Interface FSAN High Power Diplexer PRELIMINARY ODP-43-PE Ordering Information Available Options: ODP-43-PE--155x-C ODP-43-PE--622x-C ODP-43-PE--1250x-C Part numbering Definition: ODP - 43 - Half Peak Output Power -- Digital TIA - Connector Type - Temperature Range - Customer Specific • (Separator) • Blank = No TIA 155 622 1250 xxxB (B=Burst) • SCX LCX FCX STX X = A (angled) X = U (ultra) • Blank = Industrial C = Commercial (0 to 70ºC) R = Reduced Industrial (-20 to 85ºC) • Labelling, Serial Number, TIA, or shipping instructions etc. • PX PAA = -13 to -16dBm PA = -9 to -13 dBm PB = -6 to -9 dBm PC = -3 to -6 dBm PD = -1 to -3 dBm PE = -1 to +1 dBm PF = +1 and up Warnings Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Legal Notice IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at Luminent’s sole and absolute discretion. Luminent warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and Luminent expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. Luminent assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and Luminent makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. Luminent customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify Luminent for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that Luminent is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact Luminent to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © Luminent, Inc. 2002 All rights reserved Rev 1 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 • LUMINENT.COM LUMNDS222-090803