OM1812NTM

OM1805STM OM1812STM OM1815STM OM1805NTM OM1812NTM OM1815NTM ISOLATED HERMETIC TO-257AA FIXED VOLTAGE REGULATORS APPROVED TO DESC DRAWINGS Three Terminal, Fixed Voltage, 1.5 Amp Precision Positive Regulators In Hermetic JEDEC TO-257AA Package FEATURES • • • • • • • Isolated Hermetic Package, JEDEC TO-257AA Outline Output Voltages: 5V, 12V, 15V Output Voltages Set Internally to ±1% Built-In Thermal Overload Protection Short Circuit Current Limiting Product Is Also Available In Non-Isolated Package Similar To Industry Standards 7805, 7812, 7815 DESCRIPTION These three terminal positive regulators are supplied in a hermetically sealed metal package whose outline is similar to the industry standard TO-220 plastic package. All protective features are designed into the circuit, including thermal shutdown, current limiting and safe-area control. With heat sinking, they can deliver over 1.5 amps of output current. These units feature internally trimmed output voltages ±1% of nominal voltage. These units are ideally suited for Military applications where a hermetically sealed package is required. PART NUMBER DESIGNATOR Standard Military Drawing Number Omnirel Part Number 5962-8778201 UX OM1805STM 5962-8778201 TX OM1805NTM 5962-8777601 UX OM1812STM 5962-8777601 TX OM1812NTM 5962-8855301 UX OM1815STM 5962-8855301 TX OM1815NTM “U” = Isolated “T” = Non-Isolated 3.3 4 11 R2 Supersedes 1 07 R1 3.3 - 57 OM1805STM/NTM - OM1815STM/NTM ABSOLUTE MAXIMUM RATINGS @ 25°C Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +35 V Operating Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to + 150°C Storage Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to + 150°C Typical Power/Thermal Charateristics: Rated Power @ 25° C TC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15W TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3W Thermal Resistance qJC Case U. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2°C/W qJC Case T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5°C/W qJA Case T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42°C/W a ELECTRICAL CHARACTERISTICS 5 Volt Parameter Output Voltage Symbol VOUT VIN = 10V, Io = 500mA, -55°C TA 125°C (unless otherwise specified) Min. 4.92 Max. 5.08 5.15 Unit V V Test Conditions TA = 25°C VIN = 7.5V to 20V IO = 5mA to 1.0 A, P < 15W Line Regulation (Note 1) (Note 4) VIN = 8.0V to 12V VRLINE VIN = 7.5V to 20V 5 mV mV mV mV mV mV mV mV mA mA mA • 4.85 • • 12 4 10 12 Load Regulation (Note 1) VRLOAD IO = 5mA to 1.5 Amp IO = 5mA to 1.0 Amp IO = 250mA to 750 mA • • 25 6 15 6 Standby Current Drain ISCD DISCD (Line) DISCD (Load) VDO IO (pk) IDS DVIN DVOUT NO DVOUT Dt TA = 25°C, DVOUT = 100mV, IO = 1.0A TA = 25°C VIN = 35V 1.5 IO = 5mA to 1000mA VIN = 7.5V to 20V Standby Current Drain Change With Line Standby Current Drain Change With Load Dropout Voltage Peak Output Current Short Circuit Current (Note 2) • • • 6.5 0.8 0.5 mA 2.5 3.3 1.2 V A A A dB dB • f =120 Hz, DVIN = 10V (Note 3) TA = 25°C, f =10 Hz to 100KHz TA = 25°C, t = 1000 hrs. 68 2.8 3.3 Ripple Rejection • 60 40 Output Noise Voltage (Note 3) Long Term Stability (Note 3) µV/V RMS 75 mV Notes: 1. Load and Line Regulation are specified at a constant junction temperature. Pulse testing with low duty cycle is used. Changes in output voltage due to heating effects must be taken into account separately. 2. Short Circuit protection is only assured up to VIN = 35V. 3. If not tested, shall be guaranteed to the specified limits. The • denotes the specifications which apply over the full operating temperature range. 4. Minimum load current for full line regulation = 5.0 mA. 3.3 - 58 OM1805STM/NTM - OM1815STM/NTM ELECTRICAL CHARACTERISTICS 12 Volt Parameter Output Voltage Symbol VOUT VIN = 19V, Io = 500mA, -55°C TA 125°C (unless otherwise specified) Min. 11.88 Max. 12.12 12.36 Unit V V Test Conditions TA = 25°C VIN = 14.5V to 27V IO = 5mA to 1.0 A, P < 15W Line Regulation (Note 1) (Note 4) VIN = 16V to 22V VRLINE VIN = 14.5V to 27V 18 mV mV mV mV mV mV mV mV mA mA mA • 11.64 • • 50 9 30 32 Load Regulation (Note 1) VRLOAD IO = 5mA to 1.5 Amp IO = 5mA to 1.0 Amp IO = 250mA to 750 mA • • 60 20 40 6.0 Standby Current Drain ISCD DISCD (Line) DISCD (Load) VDO IO (pk) IDS DVIN DVOUT NO DVOUT Dt DVOUT = 100mV, IO = 1.0A TA = 25°C VIN = 35V IO = 5mA to 1000mA VIN = 15V to 30V Standby Current Drain Change With Line Standby Current Drain Change With Load Dropout Voltage Peak Output Current Short Circuit Current (Note 2) Ripple Rejection • • • • 1.5 6.5 0.8 0.5 mA 2.5 3.3 1.2 V A A A dB dB • f =120 Hz, DVIN = 10V (Note 3) TA = 25°C, f =10 Hz to 100KHz TA = 25°C, t = 1000 hrs. 61 2.8 • 54 40 Output Noise Voltage (Note 3) Long Term Stability (Note 3) µV/V RMS 120 mV Notes: 1. Load and Line Regulation are specified at a constant junction temperature. Pulse testing with low duty cycle is used. Changes in output voltage due to heating effects must be taken into account separately. 2. Short Circuit protection is only assured up to VIN = 35V. 3. If not tested, shall be guaranteed to the specified limits. 4. Minimum load current for full line regulation = 5.0 mA. The • denotes the specifications which apply over the full operating temperature range. 4. Minimum load current for full line regulation = 5.0 mA. MECHANICAL OUTLINE .420 .410 .200 .190 .045 .035 .665 .645 .537 .527 .430 .410 .038 MAX. CONNECTION DIAGRAM 3.3 4 .150 .140 .750 .500 .005 Case T 1 Input 2 Ground 3 Output 4 Ground 1 2 3 Case U 1 Input 2 Ground 3 Output 4 No Connection .035 .025 .100 TYP. .120 TYP. 3.3 - 59 OM1805STM/NTM - OM1815STM/NTM ELECTRICAL CHARACTERISTICS 15 Volt Parameter Output Voltage Symbol VOUT VIN = 23V, Io = 500mA, -55°C TA 125°C (unless otherwise specified) Min. 14.8 Max. 15.2 15.4 Unit V V Test Conditions TA = 25°C VIN = 18.5V to 30V IO = 5mA to 1.0 A, P < 15W • 14.6 Line Regulation (Note 1) (Note 4) VRLINE VIN = 17.5V to 30V 20 mV mV mV mV mV mV mV mV mA mA mA • VIN = 20V to 26V 50 15 • Load Regulation (Note 1) VRLOAD IO = 5mA to 1.5 Amp IO = 5mA to 1.0 Amp IO = 250mA to 750 mA 25 35 • • 75 21 45 6.0 Standby Current Drain ISCD DISCD (Line) DISCD (Load) VDO IO (pk) IDS DVIN DVOUT NO DVOUT Dt TA = 25°C, DVOUT = 100mV, IO = 1.0A TA = 25°C VIN = 35V 1.5 IO = 5mA to 1000mA VIN = 18.5V to 30V Standby Current Drain Change With Line Standby Current Drain Change With Load Dropout Voltage Peak Output Current Short Circuit Current (Note 2) Ripple Rejection • • • 6.5 0.8 0.5 mA 2.5 3.3 1.2 V A A A dB dB • f =120 Hz, DVIN = 10V (Note 3) TA = 25°C, f =10 Hz to 100KHz TA = 25°C, t = 1000 hrs. 54 2.8 • 52 40 Output Noise Voltage (Note 3) Long Term Stability (Note 3) µV/V RMS 150 mV Notes: 1. Load and Line Regulation are specified at a constant junction temperature. Pulse testing with low duty cycle is used. Changes in output voltage due to heating effects must be taken into account separately. 2. Short Circuit protection is only assured up to VIN = 35V. 3. If not tested, shall be guaranteed to the specified limits. The • denotes the specifications which apply over the full operating temperature range. 4. Minimum load current for full line regulation = 5.0 mA. TYPICAL PERFORMANCE CHARACTERISTICS 3.3 3.5 3 PEAK OUTPUT 2.5 DROPOUT VOLTAGE 100 RIPPLE REJECTION Tj = -55°C 2 Output Current (A) 2.5 1.5 2 Tj = 25°C IOUT = 500mA Ripple Rejection (dB) IOUT = 1A 80 VOUT = 5V 60 1.5 1 Tj = 150°C 1 IOUT = 0A 40 VIN - V = 8VDC +3.5Vrms IOUT = 1A Tj = 25°C 0.5 DVOUT = 100MV 0.5 0 0 20 DVOUT = 100mV 5 10 15 20 25 30 35 0 -75 -50 -25 0 25 50 75 100 125 150 0 10 100 1k 10k 100k Input To Output Differential (V) Junction Temperature (°C) Frequency (Hz) 205 Crawford Street, Leominster, MA 01453 USA (508) 534-5776 FAX (508) 537-4246